Error Messages - Kenwood TS-890S Instruction Manual

Error Messages

The following error messages are displayed when an abnormality is detected on this transceiver. Follow the steps described for each
error message to resolve the problem.
ID
Configurations for the Local Clock have not been completed.
(ERR: 0012)
0012
Associated functions cannot be used until the timer configurations
have been completed.
Connection to an NTP server has failed. (ERR: 0015)
0015 Ensure that the NTP server address and the network have been
correctly configured.
001B A file is invalid. (ERR: 001B)
An error occurred while a file was being read from a USB flash
001C
drive. (ERR: 001C)
A USB flash drive cannot be detected. (ERR: 002F)
Failure to detect the USB flash drive may be caused by the
following.
• The USB flash drive is not correctly connected to a USB
002F
connector.
• The USB flash drive is not in the specified format. The USB
flash drive must be formatted in the "USB/File Management"
screen.
An error occurred while a file is being written to an internal memory
0030
area or a USB flash drive. (ERR: 0030)
003B Failure in Deleting of a File. (ERR: 003B)
Safe Removal of USB Flash Drive was failed. (ERR: 003C)
The data file may not be stored onto the USB flash drive.
003C
Turn OFF the DC power supply, and then disconnect the USB
flash drive.
A failure in detecting the firmware file will terminate the firmware
updating process. (ERR: 003E)
The termination of the firmware update may be caused by the
following:
• The firmware file is not stored in the specified folder.
• The USB flash drive is not in the specified format.
003E
• The USB flash drive must be formatted in the "USB/File
Management" screen.
• The newer version firmware has already been applied to the
transceiver.
• The firmware file is not legitimate.
Restart the transceiver and then execute the firmware update
again from the beginning.
The selected file cannot be read by this transceiver with the earlier
version firmware installed. (ERR: 003F)
003F
Update the transceiver firmware using the latest version of the
firmware.
A failure in updating the firmware terminates the firmware updating
0040 process. (ERR: 0040)
Refer to "Troubleshooting" in the instruction manual.
The storage location cannot be changed while an audio recording.
0046
(ERR: 0046)
The storage location cannot be changed while a CW QSO log
0047
recording. (ERR: 0047)
The storage location cannot be changed while a RTTY QSO log
0048
recording. (ERR: 0048)
Message
TROUBLESHOOTING 18
Description/Corrective Action
Appears when attempting to launch the program timer while a local clock
is not configured. Configure the local clock in Clock menus [00] to [03].
Appears when date/time data cannot be successfully acquired from the
NTP server.
Follow the instructions in the error message.
Appears when a file error is detected while reading a file that contains
the RX equalizer, TX equalizer and settings data.
Appears when a file error is detected while reading a file stored in the
USB flash drive that contains the RX equalizer, TX equalizer and settings
data.
Appears when some unknown problem has occurred on the USB flash
drive.
Follow the instructions in the error message.
Appears when the file name is duplicated or an unexpected error has
occurred. Follow the instructions in the error message.
Appears when the deletion of file failed. Make sure the USB flash drive
is not write-protected.
Appears when some problem has occurred while unmounting the USB
flash drive.
Follow the instructions in the error message.
Appears when some unknown problem has occurred while reading the
firmware file.
Follow the instructions in the error message.
Appears when attempting to read a settings file written by a transceiver
installed with a new firmware using a transceiver with an old firmware.
Follow the instructions in the error message.
Appears when some unknown problem has occurred while rewriting the
firmware file.
Appears when attempting to change the destination for saving the file
while manual recording is in progress.
Appears when attempting to change the destination for saving the file
while CW communication log recording is in progress.
Appears when attempting to change the destination for saving the file
while RTTY communication log recording is in progress.
18-9