Saving A Screen Shot; Configuring Output To An External Meter; Configuring The Output Signal Format Of The External Meter; Configuring The External Meter Output Level - Kenwood TS-890S Instruction Manual

16 OTHER FUNCTIONS

Saving a Screen Shot

This transceiver comes with a screen capture function to capture
an image of the screen display and save the image data in the PNG
format (.png) to the built-in memory or a USB flash drive.
1 Assign "Capture" to a PF key.
• To save the image data to a USB flash drive, insert a USB
flash drive into
2 Press PF [Capture].
• The memory icon being selected as the storage destination
blinks. A shot of the screen is captured at the same time
when the key is pressed, and the captured data is saved to
a USB flash drive. The directory of the storage destination
is "KENWOOD\TS-890\CAPTURE".
• When removing the USB flash drive, make sure to execute
"Safely Removing the USB Flash
The saved file is named as follows.
●
yyyymmdd_hhmmss.png
(Example)
20180215_102030.png
(When the screen shot is saved on February 15, 2018,
10:20:30 a.m.)
• When saving the screen capture to a USB flash drive,
check the following in advance.
The USB flash drive is formatted by this transceiver.
The USB flash drive is correctly inserted into this
transceiver.
There is sufficient free space on the USB flash drive.
The USB flash drive is not write-protected or the file
system is not corrupted.
A screen shot can also be captured and saved by
●
pressing [Print Screen] on the USB keyboard.
A screen shot cannot be captured when the screen saver
●
is active.
When screen capture fails, an error tone is output.
●
It might take some time before the captured image is
●
written to a USB flash drive. If there is an attempt to safely
remove the USB flash drive, a message will be displayed
asking the user to wait until the captured image file is
saved to the USB flash drive before attempting to remove
it.
16-6
(USB-A).
Drive" (11-6).

Configuring Output to an External Meter

The TX or RX signal level can be displayed by connecting an
analog meter to the METER terminal on the rear panel of this
transceiver. A different output signal format can be configured for
each of External Meter 1 and External Meter 2.
The signal to be output to the external meter during transmission
can be configured as follows. During reception, the signal strength
will be output as signals to the external meter.
Output rating of METER terminal:
Voltage: 0 to 5 V (no load)
Impedance: 4.7 kΩ
Configuring the Output Signal Format of the External
Meter
Configure the signal that is output from the METER terminal to the
external meter.
Configure in Advanced Menu [0] "Indication Signal
Type (External Meter 1)" (External Meter 1) or
Advanced Menu [1] "Indication Signal Type
(External Meter 2)" (External Meter 2)
Automatic (default: External Meter 2)/ TX Power
(default: External Meter 1)/ ALC/ Drain Voltage
Setting Value
(Vd)/ Compression Level (COMP)/ Current (Id)/
SWR
Automatic: Outputs the S meter level during reception, and the
signal level or meter value displayed on F [METER] during
transmission.
TX Power: Outputs the TX output power value.
ALC: Outputs the ALC level.
Drain Voltage (Vd): Outputs the drain voltage of the final FET.
Compression Level (COMP): Outputs the degree of audio
signal enhancement by the speech processor.
Current (Id): Outputs the drain current of the final FET.
SWR: Outputs the standing wave ratio (SWR).

Configuring the External Meter Output Level

External Meter 1 and External Meter 2 can be configured to
different signal levels that are output from this transceiver
according to the rating of the external meter that is connected to
the METER terminal.
Configure in Advanced Menu [2] "Output Level
(External Meter 1)" (level of external meter output
1) or Advanced Menu [3] "Output Level (External
Meter 2)" (level of external meter output 2)
Setting Value 0% to 50% (default) to 100% (1 step)
• At "100%", the voltage is 5 V.