Page 1
Technical Support and E-Warranty Certificate www.vevor.com/support DIAMOND CORE DRILL USER MANUAL We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and doses not necessarily mean to cover all categories of tools offered by us.
Page 3
CustomerService@vevor.com This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if...
Page 4
The symbols used in this manual are intended to alert you of the possible risks. Please fully read the safety signs and instructions below. The warning themselves do not prevent the risks and can not be a substitute for proper methods of avoiding accidents. This symbol, placed before a safety comment, indicates a kind of precaution, waning, or danger.
This product is subject to the provision of European Directive 2012/19/EC. The symbol showing a crossed-out wheeled bin indicates that the product requires separate refuse collection in the European Union. This symbol applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to a collection point for recycling electrical and electronic devices.
Page 6
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Page 7
tool. Carrying power tools with your finger on the switch or energizing power tools with the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
Page 8
considering the working conditions and the work to be performed. Using the power tool for operations different from those intended could result in a hazardous situation. 5) Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts.
avoid the drill core injuring the persons downstairs or damaging the property downstairs. Connecting the soft pipe with the inner diameterΦ16mm to the adaptor of the valve. 10. Please ensure that there is no water leak so that it will not dampen the motor when you use the liquid and the attachments.
Page 10
minutes for the bit to cool and then restart the switch to continue drilling. If the clutch continues to slip, please stop drilling and re-tighten the clutch. 5. Remove drill core: When the drill bit almost drills through the floorboard or wall etc materials, be careful in reducing its drill speed to avoid drilling forcibly.
Widely used in construction, pipeline installation, road, bridge and engineering quality control, sampling and other fields. 5. MAIN TECHNICAL PARAMETER Model Z1Z-9260 Rated voltage 220-230V~ For EU and AUS 120V~ For US Rated frequency...
Page 12
on the rotor spindle. The brand of special lubricating oil is 110# industrial gear oil. It is not allowed to use common engine oil. 5) Keep the drill clean and dry. If not in use, please clean the drill and keep it in a dry and clean place.
Page 13
8. MAIN PART LIST AND THE BREAKDOWN DRAWING THE PARTS LIST OF Z1Z-9260 ENGINEERING DRILL...
Page 15
Z1Z-CF-9260 Explosion view part list Part Name Part Name Output shaft #5 gear shaft Flat key A8×18 Flat key C5×25 Retaining ring for hole #2 Gear φ55 Oil seal ring φ42×55×8 Flat key A5×12 Faucet G1/4 #3 gear shaft Water seal cover Sealing gasket Adjusting washer Middle cover...
Page 16
Brush holder fixing Switch DZ47S IPD 32A gasket Large flat head screw Cross pan head screw M4×8 M4×14 Spring washer φ4 Pressing plate Cross tapping screw Switch box ST4.2×13 Carbon Brush 8×18×22 Cable sheath Carbon brush cover Cable 3×1.5×2.3m Cross tapping screw Cross pan head screw ST3.5×13 M4×16...
Page 17
Hexagon socket head Hexagon bolt M12×68 cap screw M5×16 Lifting unit handle Flat gasket φ12 Hexagon socket head Bakelite handle sleeve cap screw M8×35 Hexagon socket head Sleeve clip parts cap screw M8×20 Spring washer φ8 Lever sleeve Hexagon bolt M10×110 Handle lever Flat gasket φ10 Bearing 6003...
Page 20
Technical Support and E-Warranty Certificate www.vevor.com/support...
Need help?
Do you have a question about the Z1Z-9260 and is the answer not in the manual?
Questions and answers