Making Cappuccinos And Milk-Based Coffees; Filling And Attaching The Milk Container; Adjusting The Amount Of Froth; Making Cappuccinos And Milk-Based Coffees Automatically - DeLonghi ECAM37X.85 Manual

Please note:
• : press to interrupt preparation completely
and go back to the homepage.
SAFETY WARNING:
After making the pot of coffee, leave the ap-
pliance to cool for 5 minutes before making
another beverage. Risk of overheating!
9. MAKING CAPPUCCINOS AND MILK-
BASED COFFEES
Please note!
To avoid milk with poor froth or large bubbles, always clean the
milk container lid (E2) and hot water connection nozzle (A8)
as described in sections "9.4 Cleaning the milk container after
use", "12.10 Cleaning the milk container" and "12.11 Cleaning
the hot water nozzle".

9.1 Filling and attaching the milk container

1. Remove the lid (E2) (fig. 14);
2. Fill the milk container (E3) with a sufficient quantity of milk,
not exceeding the MAX level marked on the container (fig.
15). Each mark on the side of the container corresponds to
about 100 ml of milk;
Please note!
• For a denser more even froth, you must use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
• If "Energy Saving" mode is enabled, you may have to wait a
few seconds before the beverage is delivered.
3. Make sure the milk intake tube (E4) is correctly inserted in
the bottom of the milk container lid (fig. 16);
4. Place the lid back on the milk container;
5. Remove the hot water spout (D6);
6. Attach the milk container (E) to the connection nozzle (A8)
and push as far as it will go (fig. 17). The machine emits a
beep (if the beep function is enabled);
7. Place a sufficiently large cup under the coffee spouts (A9)
and the frothed milk spout (E5). Adjust the length of the
milk spout. To move it nearer the cup, simply pull it down-
wards (fig. 18).
8. Follow the instructions below for each function.

9.2 Adjusting the amount of froth

Turn the froth adjustment dial (E1) to adjust the amount of froth
on the milk delivered while making cappuccinos and milk-based
coffees.
Dial Description
position
NO FROTH
MIN. FROTH
MAX. FROTH

9.3 Making cappuccinos and milk-based coffees

automatically
1. Fill the milk container (E) and attach it as described above.
2. Select the required beverage:
• CAPPUCCINO
• LATTE MACCHIATO
• HOT MILK
• CAPPUCCINO+
• CAPPUCCINO MIX
• CAFFELATTE
• FLAT WHITE
• ESPRESSO MACCHIATO
3. A message on the display instructs you to turn the froth
adjustment dial (E1) according to the froth required by the
original recipe. Turn the dial on the milk container lid.
4. After a few seconds, preparation begins automatically and
an image of the selected beverage appears on the display,
together with a progress bar which gradually fills as prepa-
ration progresses.
Once the coffee has been made, the appliance is ready to make
the next beverage.
Please note: general indications when preparing all milk-
based beverages
• : press to interrupt preparation completely
and go back to the homepage.
• : press to interrupt milk or coffee delivery and
move on to the next delivery (if applicable) to complete the
beverage.
• Preparation of each coffee can be customised (see section
"11. Customising the beverages").
• Do not leave the milk container out of the refrigerator for
long periods. The warmer the milk (5°C is ideal), the poorer
the quality of froth produced.
9.4

Cleaning the milk container after use

Each time you use a milk function, "TURN MILK FROTH ADJUST-
MENT DIAL" "TO CLEAN POSITION" appears on the display and
the milk frother lid must be cleaned:
12
Recommended for...
HOT MILK (not frothed) /
CAFFELATTE
latte macchiato/
FLAT WHITE
CAPPUCCINO / CAPPUCCI-
NO+ / CAPPUCCINO MIX
/ ESPRESSO MACCHIATO /
HOT MILK (frothed)