Table of Contents
Advertisement
1. Leave the milk container (E) in the machine (you do not
need to empty it);
2. Place a cup or other recipient under the frothed milk spout;
3. Turn the froth adjustment dial (E1) to "CLEAN" (fig. 19).
"CLEANING UNDERWAY" "RECIPIENT UNDER SPOUT" ap-
pears on the display together with a bar which gradually
fills as cleaning progresses (fig. 20). Steam mixed with hot
water comes out of the frothed milk spout. Cleaning stops
automatically;
4. Turn the dial back to one of the froth selections;
5. Remove the milk container and always clean the hot water
connection nozzle (A8) with a sponge (fig. 21).
Please note!
•
To prepare a number of cappuccinos and milk based cof-
fees, clean the milk container after you have prepared
the last beverage only. To proceed with making the next
beverages, when the CLEAN message is displayed, press
.
•
If you do not clean the milk container, the
pears on the display to remind you that it needs cleaning.
•
The milk container can be kept in the refrigerator.
•
In some cases, to clean you must wait for the appliance to
heat up.
10.
DELIVERING HOT WATER
1. Make sure the hot water spout (D6) is attached correctly to
the hot water connection nozzle(A8);
2. Place a container under the spout (as close as possible to
avoid splashes);
3. Press "HOT WATER"; The corresponding image appears on
the display, together with a progress bar which fills gradu-
ally as preparation proceeds;
4. The machine delivers hot water, then delivery stops auto-
matically. To interrupt hot water delivery manually, press
.
Please note!
•
If "Energy Saving" mode is active, you may have to wait a few
seconds before the hot water is delivered.
•
Preparation of hot water can be customised (see section
"11. Customising the beverages").
11.
CUSTOMISING THE BEVERAGES
The aroma (when required) and quantity of the beverages can
be customised.
1. Press
(C2);
2. To access the customising screen, choose the beverage you
want to customise. The corresponding accessories must be
inserted;
3. (Coffee beverages only) Select the required aroma by
pressing "-" or "+" and press
4. Preparation begins and the appliance displays the quantity
customising screen in the form of a vertical bar. The star
alongside the bar represents the current quantity;
5. When the amount reaches the minimum quantity you can
set,
6. Press
is reached;
7. Press
The appliance confirms if the values have been saved or not (de-
pending on the previous selection). Press
The appliance goes back to the homepage.
Please note!
•
Cappuccinos and milk-based coffees: the coffee aroma
is saved first, followed by the quantity of first milk, then
coffee;
•
Hot water: the appliance delivers hot water. Press
symbol ap-
•
You can also customise the beverages by connecting with
the DeLonghi Coffee Link App.
•
Press
not be saved.
Beverage quantity table
Beverage
ESPRESSO
LONG
COFFEE
DOPPIO+
HOT WATER
12.
12.1 Cleaning the machine
The following parts of the machine must be cleaned regularly:
•
the appliance's internal circuit;
•
coffee grounds container (A11);
•
drip tray (A15), condensate tray (A10), drip tray grille (A14)
and tray full indicator (A13);
•
water tank (A17);
•
coffee spouts (A9);
•
pre-ground coffee funnel (A4);
•
infuser (A20), accessible after opening the infuser door
(A19);
•
milk container (E);
13
is displayed;
when the required quantity in the cup
to save (or
to save the required quantity.
to exit programming. The values will
Standard
quantity
40 ml
160 ml
180 ml
120 ml
250 ml
CLEANING
;
to cancel).
.
Programmable
quantity
20-180 ml
115-250 ml
100-240 ml
80-180 ml
20-420 ml
Advertisement
Table of Contents
Troubleshooting
