1. Manuals
  2. Brands
  3. Texi Manuals
  4. Sewing Machine
  5. Tronic 5
  6. Operation manual

Texi Tronic 5 Operation Manual

High speed direct drive automatic lockstitch machine with built-in energy saving motor
Hide thumbs
Table of Contents

Advertisement

Quick Links

Operation manual
for high speed direct drive automatic lockstitch
machine
with built-in energy saving motor
Tronic 5

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Tronic 5 and is the answer not in the manual?

Questions and answers

Rikke Skøt Jøker
January 24, 2025

Hej jeg har en Texi Tronic 5 hvilken olie skal der på kan ikke finde det i brugsanvisning

0
1 comments:
Mr. Anderson
February 10, 2025

High-speed machine oil should be used for the Texi Tronic 5.

This answer is automatically generated

0

Subscribe to Our Youtube Channel

Related Manuals for Texi Tronic 5

Summary of Contents for Texi Tronic 5

  • Page 1 Operation manual for high speed direct drive automatic lockstitch machine with built-in energy saving motor Tronic 5...

  • Page 3: Table Of Contents

    TEXI Tronic 5 operation manual Contents Safety precautions User’s manual for the automatic lockstitch machine 1. Before starting work 2. Installation 3. Lubrication 4. Correct oil dosage to the hook 5. Fastening the needle 6. Insertion of bobbin into bobbin case 7.

  • Page 4: Before Starting Work

    TEXI Tronic 5 operation manual IMPORTANT! This instruction manual contains important guidelines regarding correct, safe and economical method of use of the machine. Following recommendations contained in this manual will decrease work down-time, increase machine reliability and durability, and will make work safer.
  • Page 5 TEXI Tronic 5 operation manual USER’S MANUAL The lockstitch machine TEXI, Tronic 5, is a high speed sewing machine, designed for sewing woven or knitted mate- rials or other textiles. Attention! The machine is not to be used for other materials than those for which it has been designed.

  • Page 6: Installation

    TEXI Tronic 5 operation manual 2. Installation Installation of the oil reservoir: The oil reservoir should rest upon four corners of the cut-out in the machine table-top (Fig. 1). - Fasten the two-armed washer [1] on side A of the oil reservoir [3], in the direction of the operator, Fig. 2.) - Fasten the two washers [2] on side B of the oil reservoir [3], (from the side of the hinges), then fasten the oil res- ervoir [3] (Fig.

  • Page 7: Correct Oil Dosage To The Hook

    TEXI Tronic 5 operation manual 4. Correct oil dosage to the hook 1. Before starting regulation: 1) First, for testing, the new machine should operate for about 3 minutes without material. 2) Checking oil using the paper oil level indicator should be carried out during the machine’s operation.

  • Page 8: Fastening The Needle

    TEXI Tronic 5 operation manual 5. Fastening the needle Before fastening the needle, turn power off. 1. Select needle size and tip appropriate to the stitch and material type. 2. Turn the pulley until the needle bar is found in its highest point.

  • Page 9: Winding The Bobbin

    TEXI Tronic 5 operation manual 8. Winding the bobbin Set the bobbin on to the bobbin winder and wind the thread onto the bobbin as shown on the figure . 9. Stitch length regulation 1. Turn the stitch length regulation dial [1] in the di- rection of the arrow and set the desired value at indicator A on the machine arm.

  • Page 10: Replacing Counter Knife And Moving Knife

    TEXI Tronic 5 operation manual 11. Replacing counter knife and moving knife Counter knife dismantling: 1) Turn machine off. 2) Release screw [1] and pin [2]. 3) Release screw [3] and counter knife [4] (fig. 16). If the counter knife does not cut thread, it should be replaced.

  • Page 11: Thread Cutting Regulation

    TEXI Tronic 5 operation manual 12. Thread cutting regulation Thread cutter cam position regulation. Turn the machine’s pulley. The needle bar will rise to 5 mm from the lower dead point, and the thread cutting cam will be pressed in and will push the roller ball, causing contact with the groove of the thread cutting cam [1].

  • Page 12: Lifting Presser Foot By Means Of The Knee Lifter

    TEXI Tronic 5 operation manual 13. Lifting presser foot by means of the knee lifter 1. The standard presser foot lifting height, when it is raised by the knee lifter, is equal to 10 mm. 2. This height can be increased to 13 mm by means of the knee lifter regulation screw [1].

  • Page 13: Thread Tensioner

    TEXI Tronic 5 operation manual 15. Thread tensioner 1. Thread cutting tensioner regulation: 1) After turning tensioner knob [1] to the right (direction A) the thread remaining in the needle after cutting will be shorter. 2) After turning the knob to the left (direction B), length will increase.

  • Page 14: Foot Pressure Regulation

    TEXI Tronic 5 operation manual 18. Foot pressure regulation 1. Loosen nut [2]. After turning the pressure regulator to the right (direction A) pressure will increase. After turning the regulator to the left (direction B) pres- sure will decrease. 2. After setting the pressure, tighten nut [2].

  • Page 15: Feed Dog Height Regulation

    TEXI Tronic 5 operation manual 21. Feed dog height regulation 1. The feed dog factory setting enables its sliding out over the surface of the needle plate at a height of 0.75 to 0.85 mm (1.15 to 1.25 mm for heavy materi- als).

  • Page 16: Setting Thread Guide

    TEXI Tronic 5 operation manual 24. Setting thread guide 1. During sewing of thick materials, the thread guide [1] should be shifted to the left (direction A) in order to increase the length of thread pulled by the thread take-up.

  • Page 17: Changing Pedal Pressing Force

    TEXI Tronic 5 operation manual 26. Changing pedal pressing force 1. Setting pressure necessary for pressing the front part of the pedal: 1) The pressure can be changed by setting the position of the pressure regulation spring [1]. 2) Pressure is decreased when the spring is at- tached on the left side.

  • Page 18: Automatic Reverse Feed Stitching Mechanism

    TEXI Tronic 5 operation manual 28. Automatic reverse feed stitching mechanism 1. Using the mechanism: 1) After pressing switch [1] the machine immediately goes into reverse feed stitching mode. 2) The machine sews in the reverse direction as long as the switch is activated.
  • Page 19 TEXI Tronic 5 operation manual Ask your supplier about:...
  • Page 20 TEXI Tronic 5 operation manual CE DECLARATION OF CONFORMITY Distributor: Strima Sp. z o.o. Swadzim, st. Poznańska 54 62-080 Tarnowo Podgórne, Polska We declare, that the following product: Automatic lockstitch machine model Tronic 5 (ZJ9703AR-D4J/01) which this declaration relates, complies with the following directives:...
  • Page 24 Dealer:...

Table of Contents