Advertisement

Quick Links

NCTE-Readout Unit Manual

NCTE-Readout Unit
Manual
Thank you for choosing our product!
This manual supports you in the correct handling as well as the careful use of the described services.
The informa�on contained in this manual has been compiled with the greatest possible care by our
specialists, but excludes legal obliga�ons in the sense of commercial law. Informa�on on specific properties
or suitability for par�cular applica�ons cannot be derived. Unauthorised modifica�ons by the user also mean
possible damage to the device, for which NCTE cannot be held liable. NCTE reserves the right to make changes
to the product without prior no�ce.
Read these instruc�ons carefully and follow their instruc�ons.
Pay par�cular a�ention to danger signs and hazard warnings:
ATTENTION!
Non-observance may cause damage to hardware and software or impair the func�on.
NCTE-Readout Unit
Manual
- All data without guarantee subject to technical changes -
T E S T E N G I N E E R I N G L T D
V22-01
Page1 of 21

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NCTE and is the answer not in the manual?

Questions and answers

Summary of Contents for Hydrotechnik NCTE

  • Page 1: Ncte-Readout Unit Manual

    Unauthorised modifica�ons by the user also mean possible damage to the device, for which NCTE cannot be held liable. NCTE reserves the right to make changes to the product without prior no�ce.
  • Page 2: Table Of Contents

    NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D Table of Contents NCTE-Readout Unit Manual ..........................1 1. Safety instruc�ons and assembly recommendations ..................3 1.1. Safety instructions ..........................3 1.2.
  • Page 3: Safety Instruc�Ons And Assembly Recommendations

    NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D 1. Safety instruc�ons and assembly recommenda�ons 1.1. Safety instructions ● Please read the instructions carefully before first use. ●...
  • Page 4: General

    2.2. Properties ● Power supply 15 ... 30 VDC ● compa�ble to all NCTE torque sensors with analog signal, 0 ... 10V - input ● counter input for incremental protractors or signal types UP-DOWN/STEP DIRECTION ● Recording possibility of min./max. measured values ●...
  • Page 5: Overview / Descrip�On - Front Side Of The Device

    NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D 2.3. Overview / descrip�on – front side of the device Func�on Description LEFT/ESC Pushbuttons for menu control to confirm or undo selected se�ngs.
  • Page 6: Supply Voltage

    NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D 2.4.1. Supply voltage The readout unit is to be operated with constant voltage of 15...30 VDC. ATTENTION! Reversing the polarity or exceeding the maximum specified voltage will damage the readout unit.
  • Page 7: In1/In2 Digital Inputs

    NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D 2.4.4. IN1/IN2 digital inputs The readout unit is equipped with two external inputs, which can be used to acquire or stop measurements depending on the opera�ng status.
  • Page 8: Display / Lcd Display

    NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D 3. Display / LCD display In the main menu of the readout unit, various information on different se�ngs is displayed. Switching between the modes is done with the keys .
  • Page 9: Menu

    NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D 4. Menu To enter the menu, press the key. To select the individual menus, press the key, to select further...
  • Page 10 NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D Source Torque input / angle measurement input / 0-10 V input Limit value range /ON -9999.999…+9999.999 Limit value range /OFF -9999.999…+9999.999...
  • Page 11: Se�Ngs - Counter Input

    NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D 4.1. Se�ngs – Counter input Se�ngs of parameters for counter input (A and B signals). Counter reset Reset�ng the acquired coun�ng pulses of the input counter...
  • Page 12: Se�Ng - 0

    NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D 4.2. Se�ng - 0…10 V voltage input Se�ngs of the parameters for the voltage input. Input set�ng Removal of the voltage input (offset) Func�on end...
  • Page 13: Se�Ngs - Pk Outputs / Relay Outputs

    NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D 4.4. Se�ngs – PK outputs / relay outputs Enables on/off switching of PK1/PK2 relays. PK1/PK2 relays can be switched on and off after exceeding values and in case of overload by fixed values, which can be torque sensors, angle measurements and input voltage.
  • Page 14: Measurement Data Acquisi�On

    NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D 4.5. Measurement data acquisition Enables se�ngs on the readout unit for recorded measurement data and the recorded minimum/maximum values.
  • Page 15 NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D Acquisi�on time (times for measurement data) Se�ng of the acquisi�on time with which the data are recorded as well as the current maximum value of the torque input.
  • Page 16: General Se�Ngs

    NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D Regardless of the selected acquisi�on mode, values of 3 measurement inputs (input torque, input angle and input voltage value) are always recorded.
  • Page 17 NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D Display se�ng Basic se�ngs after switching on the device Func�on end Possibility to select se�ngs Change confirmation and menu end Password se�ng...
  • Page 18: Memory Card

    NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D 4.7. Memory card Memory card information Informa�on about memory size in MB (megabyte) and available memory capacity Return to menu...
  • Page 19: Memory Card

    NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D 5. Memory card The readout unit can record acquired measurement data on a memory card located on the back of the device.
  • Page 20: Pc Program

    NCTE-Readout Unit Manual T E S T E N G I N E E R I N G L T D 7. PC Program The readout unit can cooperate with the PC program, which allows se�ngs at PC level. Furthermore, the program allows to collect measurement data in real time and save them as a file (*.csv →...
  • Page 21: Safety And Opera�Ng Instruc�Ons

    Do not use products such as water or oil to clean the unit. - All data without guarantee subject to technical changes - Hydrotechnik UK Test Engineering Ltd, 1 Central Park, Lenton Lane, Nottingham, NG7 2NR, UK +44 (0)115 9003 550 sales@hydrotechnik.co.uk...

Table of Contents