Subscribe to Our Youtube Channel
Related Manuals for Regency City Series San Francisco Bay 40
Summary of Contents for Regency City Series San Francisco Bay 40
- Page 1 MUST READ BEFORE FRAMING IMPORTANT INFORMATION Regency City Series San Francisco Bay 40 CB40E-NG11 / CB40E-LP11 FRAMING DIMENSIONS SPECIFICATIONS HEAT RELEASE REQUIREMENTS QR LINK FOR PDF DIGITAL COPY OF SPECIFICATIONS:...
- Page 2 Gas Line Entry throughout this manual. The inches are rounded to the City Series CB40E-11...
-
Page 3: Ventilation Openings
Ventilation Openings Release warmth into the room discreetly Ventilation Opening Locations The following are examples of how the ventilation openings may be placed ventilation opening. The ventilation opening(s) must be a minimum 120 Top Exit Front Exit The ventilation opening may be short of the ceiling as shown below. The ventilation opening may be placed in front ensuring it meets the 120 enclosure to the ceiling and must be in open in front and both sides to The ventilation opening may be fully open at the top of the enclosure. -
Page 4: Chase Enclosure
Chase Enclosure top of the chase enclosure for all installations. examples shown in this manual. Internal chase: enclosure causing the enclosure to overheat. It is vital that all the hot air from within the enclosure exits through the ventilation openings only. Top of chase enclosure Top of chase enclosure Top of chase... -
Page 5: Locating Your Gas Fireplace
Locating Your Gas Fireplace ensure that the clearances are met. WARNING! application. The appliance must be installed on a metal or wood panel extending the full width and depth of the appliance. screw. Bend into the correct shape (see above). the unit and attach the other end with one screw. - Page 6 Clearances Horizontal - Top Horizontal - Side Horizontal - Bottom B: Sidewall (on one side) Passing through wall/ floor/ceiling - when Side wall to side wall (min.) G: To Enclosure Ceiling (min/max) From top of enclosure * Top/front or side of enclosure To Top of Ceiling L: Chase Enclosure (min.) Perpendicular from chase grill...
- Page 7 Clearances Floor to ceiling with top opening Low framing with vents in front/2 sides or top Full framing with low vents in front or 2 sides Full framing with vents in front or 2 sides Note: The ventilation opening City Series CB40E-11...
- Page 8 City Series CB40E-11...
- Page 9 City Series CB40E-11...
- Page 10 City Series CB40E-11...
- Page 11 on the wall. DIMENSIONS sure. City Series CB40E-11...
- Page 12 on the wall. Repeat steps to install the second grill to the other side of the chase. DIMENSIONS sure. may not be but the drawing dipicts the process. Secure with screws through louvers to the sides. City Series CB40E-11...
-
Page 13: Mantel Leg Clearances
Mantel Clearances Combustible mantel clearances from top of front facing are shown in the diagram on the right. Mantel Leg Clearances Combustible mantel leg clearances as per diagram: City Series CB40E-11... - Page 14 NOTE: for the product to facilitate ease of installation. See instructions in this manual for details. Description Framing Height Note: Note: Note: studs in front and both header on edge sides. Studs behind can be Note: This appliance must be in- stalled on a solid surface such as a width and depth of the appliance.
- Page 15 Part A Install Screw Locations City Series CB40E-11...
- Page 16 Secure Framing to Wall Studs with wood screws Part B1 to A - screws go in from front Install Pre Assembled Sidewall Part J install to Part B1 + B2 Install Pre Assembled Sidewall (opposite) Part J screw locations City Series CB40E-11...
- Page 17 Part O Part Q Part O Part B3 Attach Part O (x2) and Q (x2) to Part B2 LEFT Part B3 RIGHT Attach Part O (x2) to Part B3 Telescope LEFT + RIGHT sidewalls to desired height Attach Part S and Part H to Front of LEFT + RIGHT sides Set predetermined height when using wood panel kit City Series CB40E-11...
- Page 18 Part M Part Q Part L Attach Part M (x2) to Part L Part M Attach Part L (x2) to LEFT and RIGHT sides Screw holes in Part I Part S located on the side Part I screw holes located on the side Part I Part H Attach Part I (x2) to Part S &...
- Page 19 Attach Part P (Right) to the RIGHT SIDE + H1 Swing Parts O out and attach Attach Part P (Left) to the LEFT SIDE + H1 City Series CB40E-11...
- Page 20 Front view Part ID - extended shown Back view Part ID - extended shown City Series CB40E-11...
- Page 21 Finishing Instructions WARNING! DO NOT components. Note: It is acceptable to use a high temperature silicone sealant to adhere drywall to lower access cover panel. WARNING! PAINTING SCREWS ONLY IN SHADED AREA City Series CB40E-11...
- Page 22 1. Frame in the enclosure for the unit with framing material. local hardware store to cover cut/exposed edges of the combustible facing Note: the bottom front lip. Two (2) secure the bottom side lips and 2 secure each receptacle provided with the appliance. The wiring harness will be located on side if deciding to remove these.
-
Page 23: Tv Flush With Hearth
TV Flush with Hearth City Series CB40E-11... - Page 24 here. Remove side outer safety glass and side glass panel (if installed) CB40E shown Tabs shown for illustration purposes - tabs are on the inside of the panel 2 screws Glass Panel install video: http://bit.ly/2uqfndj Completed glass trim City Series CB40E-11...
- Page 25 here. º City Series CB40E-11...
- Page 26 City Series CB40E-11...
- Page 27 here. Edge cover Install glass hearth top (3 pieces) City Series CB40E-11...
Need help?
Do you have a question about the City Series San Francisco Bay 40 and is the answer not in the manual?
Questions and answers