Advertisement
3/8" O.D. UNPLATED COP-
1/4" O.D. TUBE
PER TUBE CONNECT
WATER INLET
COLD WATER SUPPLY
TO COOLER
NOTE: WATER FLOW
DIRECTION
Figure 10 – Water Supply Connections
PARTS LIST
ITEM NO.
PART NO.
1
56073C
2
28782C
28783C
3
LK464
4
98530C
5
45662C
6
45663C
7
75672C
8
112627543890
9
111008343890
10
56092C
11
1000001994
12
55996C
13
0000000980
14
55000661
15
55000665
16
40045C
17
28823C
18
56280C
19
75560C
20
1000001772
21
111577343890
22
70852C
23
62223C
24
1000002062
25
99003C
26
0000001153
BOTTLE FILLER REPLACEMENT
PART KITS
ITEM NO.
PART NO.
98543C
27
98544C
28
98545C
29
98546C
30
31
98549C
Note: Screw the locknut hand tight to seal
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 • www.elkay.com
0000001028 (Rev. G - 11/18)
EDFP217WS
BUILDING WATER
INLET
SERVICE STOP
(NOT FURNISHED)
DESCRIPTION
Kit - Bubbler Assy
Fountain Arm - Short
Fountain Arm - Long
Drain
Kit - Regulator/Nut/Holder
Push Button
Push Button Sleeve
Screw - Cap #6-32 x 5/16
Screw - #10-24 x .50 PHTC
Screw - #10-24 x .62 HHSM
Poly Tubing 1/4" (Cut To Length)
Kit - Tee 1/4 x 1/4 x 1/4 (3 Pack)
Strainer
Back Panel Assembly
Bottom Cover Plate - Short
Bottom Cover Plate - Long
Hex Nut
Regulator Mounting Bracket
Edge Trim - Chrome
Screw - 5/16-18 x 1.00 HHMS
Kit - Elbow 1/4 x 1/4 (3 Pack)
Nut - Hex 5/16-18
Tee - 3/8 x 3/8 x 3/8
Copper Tube - 3/8" Cut To Length
Kit - Tee 1/4 x 1/4 x 3/8 (3 Pack)
Reset Switch Assy
Reset Switch Bracket
DESCRIPTION
Kit - Electrical Package
Kit - EE Sensor
Kit - Solenoid Valve Replacement
Kit - Aerator Replacement
Kit - Hardware & Waterway Parts
Figure 11
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640
EDFP217WS*F
Installation Package
The components for installation are packed in
two separate boxes, regardless of the type of unit
being installed. The boxes contain the following:
Box No. 1: Wall Frame(s)
Box No. 2: Fountain(s), Arm(s) and Panels
Additional materials, as noted in the Parts List,
are also shipped in these boxes.
TROUBLESHOOTING & MAINTENANCE
Orifice Assembly: Mineral deposits on orifice can
Stream Regulator: If orifice is clean, regulate
flow as in Step 14 of the installation instructions. If
replacement is necessary, see parts list for correct
regulator part number.
Actuation of Quick Connect Water Fittings: Cooler
is provided with lead-free connectors which utilize an
o-ring water seal. To remove tubing from the fitting,
relieve water pressure, push in on the gray collar while
pulling on the tubing. (See Fig. 12) To insert tubing,
push tube straight into fitting until it reaches a positive
stop (approximately 3/4").
OPERATION OF QUICK CONNECT FITTINGS
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE TO ATTACH
A
A
B
B
Figure 12 – Quick Connect Fittings
Page 8
cause water flow to spurt or not
regulate. Mineral deposits may
be removed from the orifice by
poking with a small round file
not over 1/8" diameter, or using
a small diameter wire
.
DO NOT
file or cut orifice
material
TUBE IS SECURED
PUSH IN COLLET
TUBE IS SECURED
PUSH IN COLLET
IN POSITION
IN POSITION
TO RELEASE TUBE
TO RELEASE TUBE
C
C
PUSHING TUBE IN BEFORE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
PULLING IT OUT HELPS TO
RELEASE TUBE
RELEASE TUBE
Advertisement
