Advertisement
3/8" O.D. UNPLATED COP-
1/4" O.D. TUBE
PER TUBE CONNECT
WATER INLET
COLD WATER SUPPLY
TO COOLER
NOTE: WATER FLOW
DIRECTION
Figure 11 – Water Supply Connections
PARTS LIST
ITEM NO.
PART NO.
1
1
56073C
2
2
28708C
3
3
28473C
4
4
45767C
5
5
28343C
6
6
45781C
7
7
98871C
8
8
98530C
9
9
56163C
10
10
0000000930
11
11
45768C
12
12
56092C
13
13
1000001994
14
14
55996C
15
15
1000002062
16
16
27026C
17
17
111008343890
18
18
70432C
19
19
38417001
20
20
75560C
21
21
75632C
22
22
1000001772
23
23
111577343890
24
24
28395C
25
25
1000002162
26
26
99003C
BOTTLE FILLER REPLACEMENT
PART KITS
ITEM NO.
PART NO.
27
98543C
28
98544C
29
98545C
30
98546C
31
98549C
Note: Screw the locknut hand tight to seal
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 • www.elkay.com
0000001030 (Rev. K - 03/19)
ERPBD28WSC
BUILDING WATER
INLET
SERVICE STOP
(NOT FURNISHED)
DESCRIPTION
Kit - Bubbler Assy
Basin - Swirlflow
Lower Shell
Fountain Body
Cover Plate
Sleeve
Kit - Swirlflo Pushbutton/Spring
Kit - Regulator/Spring/Nut
Gasket - Drain
Kit - Drain/Tailpipe
Drain - Plug 1-1/2"
Poly Tubing (Cut To Length)
Kit - 70682C 1/4 Tee (3 Pack)
Strainer (Provided with Chiller)
Kit - Tee 1/4 x 1/4 x 3/8 (3 Pack)
Lower Panel
Screw - #10-24 x .62 HHSM
Screw - #8-32 x .38 THSM
Screw - #8-18 x .37 HHSM
Screw - 5/16-18 x 1.00 HHMS
Setscrew - #10-32 x .38
Kit - 70817C Elbow 1/4x1/4 (3 Pack
Nut - Serrated Hex 5/16-18
Bracket - Support
Kit - 70683C 1/4 Union (3 Pack)
Reset Switch Assy
DESCRIPTION
Kit - Electrical Package
Kit - EE Sensor
Kit - Solenoid Valve Replacement
Kit - Aerator Replacement
Kit - Hardware & Waterway Parts
Figure 12
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640
LRPBD2_8WSC
Installation Package
The components for installation are packed in
three separate boxes, regardless of the type
of unit being installed. The boxes contain the
following:
Box No. 1: Wall Frame(s)
Box No. 2: Remote Chiller, ECH8
Box No. 3: Fountain(s), Arm(s) and Panels
Additional materials, as noted in the Parts List,
are also shipped in these boxes.
TROUBLESHOOTING & MAINTENANCE
Orifice Assembly: Mineral deposits on orifice can
Stream Regulator: If orifice is clean, regulate
flow as in Step 14 of the installation instructions. If
replacement is necessary, see parts list for correct
regulator part number.
Actuation of Quick Connect Water Fittings: Cooler
is provided with lead-free connectors which utilize an
o-ring water seal. To remove tubing from the fitting,
relieve water pressure, push in on the gray collar while
pulling on the tubing. (See Fig. 13) To insert tubing,
push tube straight into fitting until it reaches a positive
stop (approximately 3/4").
OPERATION OF QUICK CONNECT FITTINGS
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE TO ATTACH
A
A
Figure 13 – Quick Connect Fittings
Page 8
cause water flow to spurt or not
regulate. Mineral deposits may
be removed from the orifice by
poking with a small round file
not over 1/8" diameter, or using
a small diameter wire
.
DO NOT
file or cut orifice
material
TUBE IS SECURED
TUBE IS SECURED
PUSH IN COLLET
PUSH IN COLLET
IN POSITION
IN POSITION
TO RELEASE TUBE
TO RELEASE TUBE
B
B
C
C
PUSHING TUBE IN BEFORE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
PULLING IT OUT HELPS TO
RELEASE TUBE
RELEASE TUBE
Advertisement
