Table of Contents
Advertisement
Quick Links
SWIRLFLO
™
EZWS-EDFPBM114K
INSTALLER
NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices
to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which
results in an "electrolysis" effect occurring in the fountain. This may result in water which has a
metallic taste to it or has a noticeable increase in the metallic content of the water.
When inspecting plumbing circuit, remember the line may be grounded some distance from the
installation, and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation.
Any drain fittings provided by the installer should be made of plastic which will electronically isolate
the fountain from the remainder of the building's plumbing circuits.
EDFPBM114WS
INSTALLATION, CARE & USE MANUAL
Refrigerated fountains with FLEXI-GUARD
and EZH
Review these instructions before beginning installation. Be sure that installation
conforms to all plumbing, electrical and other applicable codes.
When installation is complete, ensure these instructions are left in the plastic bag
provided inside the installed unit for future reference.
Service to be performed by authorized service personnel only.
EDFPBM114WS-F
O
Bottle Filler
®
2
LZWS-EDFPBM114K
Page 1
™
1000002503 (Rev.A - 04/15)
Advertisement
Table of Contents
Related Manuals for Elkay SWIRLFLO EZWS-EDFPBM114K
Summary of Contents for Elkay SWIRLFLO EZWS-EDFPBM114K
- Page 1 EDFPBM114WS EDFPBM114WS-F INSTALLATION, CARE & USE MANUAL SWIRLFLO Refrigerated fountains with FLEXI-GUARD ™ ™ and EZH Bottle Filler ® EZWS-EDFPBM114K LZWS-EDFPBM114K INSTALLER Review these instructions before beginning installation. Be sure that installation conforms to all plumbing, electrical and other applicable codes. When installation is complete, ensure these instructions are left in the plastic bag provided inside the installed unit for future reference.
- Page 2 EDFPBM114WS EDFPBM114WS-F Figure 1 1000002503 (Rev. A - 04/15) Page 2...
-
Page 3: Required Tools And Materials
EDFPBM114WS EDFPBM114WS-F TO BUBBLER REQUIRED TOOLS AND MATERIALS These tables show special tools and/or additional materials (not provided) which are necessary to complete installation of these units: Special Tools Description Quantity Item NONE Additional Materials Not Included TO BOTTLE Quantity Item Description FILLER... -
Page 4: Installation
EDFPBM114WS EDFPBM114WS-F 8. Install reset switch for bottle filler (Fig 4A). Connect the switch wire to the extension wire on the back of the bottle filler. Wrap up the excess cord. 28, 29, 30, 31, 32 9. Attach waste tubes (1-1/4” O.D.) to 1-1/4” O.D. slip trap. Trap on the bottle filler side must be 1-1/2”... - Page 5 EDFPBM114WS EDFPBM114WS-F Basin Locknut FLEXI-GUARD BUBBLER DETAIL ® NOTE: When installing replacement bubbler and pedestal (Fig 6), tighten locknut only to hold parts snug in position. Do Not overtighten. Figure 6 - Bubbler Details FILTER PARTS LIST LISTA DE PIEZAS DEL LISTE DES PIÈCES DU (See Fig.
- Page 6 EDFPBM114WS EDFPBM114WS-F See Fig. 6 See Fig. 6 Figure 8 - Fountain Body Assembly Regulator Figure 9 - Push Button Assembly 1000002503 (Rev. A - 04/15) Page 6...
- Page 7 EDFPBM114WS EDFPBM114WS-F BF11 PROGRAM SETTING THE CONTROL BOARD Continued from below: VERIFY CONTROL BOARD SOFTWARE 2) When the display changes to “SETTINGS”, depress the button again. 1) To verify the software program of the control board the unit will The display will change to show need to be shut down and restarted.
-
Page 8: Mounting Frame
EDFPBM114WS EDFPBM114WS-F MAIN PANEL MOUNTING FRAME DRAIN LOCATIONS MOUNTING FRAME Figure 10 3/8” O.D. UNPLATED COP- 1/4” O.D. TUBE BUILDING WATER PER TUBE CONNECT WATER INLET INLET COLD WATER SUPPLY TO COOLER SERVICE STOP NOTE: WATER FLOW (NOT FURNISHED) DIRECTION Note: Screw the locknut hand tight to seal Figure 11 –... -
Page 9: Parts List
Figure 13 – Quick Connect Fittings REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640 FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816 ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 Page 9 1000002503 (Rev.A - 04/15)