Advertisement
Quick Links
SWIRLFLO
EZWS-EDFPBM117K
INSTALLER
NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices
to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which
results in an "electrolysis" effect occurring in the fountain. This may result in water which has a
metallic taste to it or has a noticeable increase in the metallic content of the water.
When inspecting plumbing circuit, remember the line may be grounded some distance from the
installation, and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation.
the fountain from the remainder of the building's plumbing circuits.
EDFPBM117WS
INSTALLATION & USE MANUAL
Fountains with FLEXI-GUARD
®
and ezH2O
Review these instructions before beginning installation. Be sure that installation
conforms to all plumbing, electrical and other applicable codes.
When installation is complete, ensure these instructions are left in the plastic bag
provided inside the installed unit for future reference.
Service to be performed by authorized service personnel only.
EDFPBM117WS-F
Bottle Filler
®
LZWS-EDFPBM117K
plastic which will electronically isolate
Page 1
®
0000001029 (Rev. I - 03/19)
Advertisement
Related Manuals for Elkay EZWS-EDFPBM117K
Summary of Contents for Elkay EZWS-EDFPBM117K
- Page 1 ® ® and ezH2O Bottle Filler ® EZWS-EDFPBM117K LZWS-EDFPBM117K INSTALLER Review these instructions before beginning installation. Be sure that installation conforms to all plumbing, electrical and other applicable codes. When installation is complete, ensure these instructions are left in the plastic bag provided inside the installed unit for future reference.
- Page 2 EDFPBM117WS EDFPBM117WS-F Figure 1 - Rough-in Dimensions 0000001029 (Rev. I - 03/19) Page 2...
-
Page 3: Required Tools And Materials
2. Install mounting frame (instructions supplied with mounting frame. TO BUBBLER TO BUBBLER 3. (For LZWS-EDFPBM117K) I 3a. (For EZWS-EDFPBM117K) Install strainer on the input tube to the chiller (Fig. 2). 4. Install tubing. With the back panel standing close to the frame, connect ller. - Page 4 EDFPBM117WS EDFPBM117WS-F Install fountain to the remaining openings on the tee at the remote 9. Attach waste tubes (1-1/4” O.D.) to 1-1/4” O.D. slip trap. others). 10. Make 11. These products are designed to operate on 20-105 PSI supply line pressure. If inlet pressure is above 105 PSI, a pressure regulator must be installed in the supply line.
- Page 5 EDFPBM117WS EDFPBM117WS-F WATERSENTRY PLUS FILTER PARTS LIST ® (See Fig. 7) ITEM PART DESCRIPTION Water Filter Assy-3000 Gal. 51300C Inlet Fittings 51469C Figure 7 See Fig. 6 See Fig. 6 Figure 8 - Fountain Body Assembly Figure 9 - Push Button Assembly Page 5 0000001029 (Rev.
- Page 6 EDFPBM117WS EDFPBM117WS-F BF11 - BF12 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE Continued from below: 1) To verify the software program of the control board the unit will 3) When display shows “UNIT TYPE” push program button once the need to be shut down and restarted.
- Page 7 EDFPBM117WS EDFPBM117WS-F MAIN PANEL MOUNTING MOUNTING FILTER DRAIN FRAME FRAME (OPTIONAL) LOCATION Figure 10 Electrical Diagram Page 7 0000001029 (Rev. I - 03/19)
-
Page 8: Troubleshooting And Maintenance
RELEASE TUBE RELEASE TUBE Note: Screw the locknut hand tight to seal Figure 11 Figure 12 – Quick Connect Fittings ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 • www.elkay.com 0000001029 (Rev. I - 03/19) - Page 9 Connect white wire to Neutral line. g. Replace Junction Box Cover. h. Connect electrical power to installation location circuit. For Technical Service, please contact us at 1.800.476.4106 Elkay - www.elkay.com 0000000755 (Rev. D - 03/19) Halsey Taylor - www.halseytaylor.com...