Related Manuals for Directed Directechs DB3+
Summary of Contents for Directed Directechs DB3+
- Page 1 933.FORD4 DS3+ / DS4+ v3.25.198.12 2014 Ford Focus THFON1-DS4+,DS3+-ONLY Compatible (Sold Separately)
-
Page 2: Table Of Contents
Contents Introduction Vehicle function compatibilities Pre-installation and application warnings Installation Wiring diagram with T-Harness (THFON1) Wiring diagram Locating components in the vehicle Vehicle connections Module programming 2 Keys required! 1 Key required! Module programming for convenience only (skip transponder) Pairing remotes Connecting the module 8556T Temperature Sensor 8504D Combo Sensor... -
Page 3: Introduction
To configure via DirectLink mobile app (Android/iOS): 1. Follow and complete the wiring diagram(s) related to your installation through the app. 2. When installation is complete, select Configure DS4/DS4+. 3. Follow the on-screen instructions. 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights... -
Page 4: Vehicle Function Compatibilities
Brake Status (foot brake) 3x LOCK START (Start control using OEM Remote) Door Locks Status 3x LOCK STOP (Stop control using OEM Remote) E-Brake Status Accessory Activation Ignition Status Ignition Activation 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights... -
Page 5: Pre-Installation And Application Warnings
[1] Hood pin: The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin or if not supported in data. [2] Siren: The siren is only required when enabling the security features during module flashing. 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights... -
Page 6: Wiring Diagram With T-Harness (Thfon1)
(+) Parking Light (right): (-) Trunk Release: Brown/Yellow, pin 26 Brown, pin 49 (-) Lock/Unlock: Slide to open Brown, pin 11 Legend: Mandatory Connections Security Only Remote Start Only Remote Start + Security 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights... -
Page 7: Wiring Diagram
HS CAN Low 2: C2280G (BCM) Violet/Orange, pin 40 (passenger side, behind glove box) (green 2-pin connector) HS CAN High 2: Junction Connector Gray/Orange, pin 41 (white 20-pin conn. near BCM) 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights... -
Page 8: Locating Components In The Vehicle
When flashing your module for Remote Start & Security, you must Security Only manually assign the designated output to Anti Grind (AG) Starter Kill. Remote Start Only (Applicable to CORE 194+.) Remote Start + Security 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights... -
Page 9: Vehicle Connections
(+) Door Input No Connection H2/14 Brown (+) Brake Input No Connection H2/15 White/Blue (-) Activation Input No Connection H2/16 Red/Blue (-) No Connection No Connection H2/17 Black/White (-) E-Brake Input No Connection 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights... - Page 10 No Connection H4/6 Green Starter Disable (key side) No Connection H4/7 Violet (+) Starter Output No Connection H4/8 Orange (+) Accessory Output No Connection H4/9 Red/White (+) 12 Volt Input No Connection 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights...
- Page 11 H6/4 (+) 12 Volt Temperature sensor harness, 2-pin black connector (H7) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection H7/1 Black Temperature Sensor H7/2 Black Temperature Sensor 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights...
-
Page 12: Module Programming
When using Data Tach, it is recommended to follow the Tach Learning procedure; however, when using a Hardwired Tach, the procedure is mandatory. For more information, refer to the Tach Learning procedure section. You have successfully completed the module programming sequence. 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights... -
Page 13: Key Required
When using Data Tach, it is recommended to follow the Tach Learning procedure; however, when using a Hardwired Tach, the procedure is mandatory. For more information, refer to the Tach Learning procedure section. You have successfully completed the module programming sequence. 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights... -
Page 14: Module Programming For Convenience Only (Skip Transponder)
Your aftermarket remote may differ from the model shown in the illustrations. You have successfully completed the module programming sequence. 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights... -
Page 15: Pairing Remotes
When used in conjunction with Directed SmartStart ® To enable D2D communication between the DS3+/DS4+ and the Directed SmartStart one of the following actions must be performed ® before providing power to the Directed SmartStart unit: ®... -
Page 16: When Used In Conjunction With Smartstart
DO NOT connect the Directed SmartStart 2-pin power harness when using the DS3+/DS4+. Power and ground will be provided by the ® D2D connector on the module. Refer to the Directed SmartStart documentation for further details. ® D2D port configuration Caution! Do not connect the Control Center (antenna) or any digital sensors (8504D) to the white D2D1 port. -
Page 17: Manual Transmission
Manual Transmission IMPORTANT! Directed does not approve nor support installations of manual transmission and remote starts on any electronic vehicles (EV), OEM Remote Start Activation firmware, vehicles with convertibles and/or removable tops, including but not limited to Jeep Wrangler, Honda S2000, Mazda Miata, and other such vehicles. -
Page 18: Led Diagnostics And Troubleshooting
The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to “Installation MUX not detected. (wiring diagrams & vehicle wiring reference charts)” to check the connections. Flashes red x 7 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights... - Page 19 The smart key was not detected, which prevents the system from shutting down the vehicle. Flashes red x 3 Speed was detected. The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights...
-
Page 20: Soft Reset
DS3+: Release the programming button. The LED turns solid red. & Solid Release DS4+: Release the programming button. The LED turns ON blue for 1 second then solid red. & & Solid Solid x1 Sec Release 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights... -
Page 21: Tach Learning Procedure (Not Needed With Virtual Tach)
Therefore, there is no Over-Rev protection. If the vehicle attempts to remote start, but is unsuccessful, the remote start will keep the ignition on for the entire runtime period. 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights... -
Page 22: Limited Lifetime Consumer Warranty
This Warranty gives you specific legal rights and you may also have other rights which vary from state to state. VOXX DEI LLC, 2351 J. Lawson Blvd., Orlando, Florida 32824 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights... -
Page 23: Quick Reference Guide
Press & hold for 1 second to remote start. * Press & hold for 5 seconds to activate the trunk release (optional). * Icon and remote appearance may differ depending on the model purchased. 933.FORD4 3.25.198.12 2014 Ford Focus ©2023 Directed. All rights... - Page 24 SmartSchedule, vehicle status, roadside assistance, parked car finder and more. The application enables a “Cloud-Connected Car” like never before, providing 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.