Subscribe to Our Youtube Channel
Related Manuals for Classic Exhibits gravitee GK-1018
Summary of Contents for Classic Exhibits gravitee GK-1018
- Page 1 © 2023 Order #XXXXX GK-1018 - 10’ x 10’ Display 10’ Plan View 10’ SETUP INSTRUCTIONS If you would like to tell us about your experience with your setup instructions please email us at info@classicexhibits.com...
-
Page 2: Plan View
© 2023 Order #XXXXX Plan View = 1 sq foot... -
Page 3: General Setup Instructions
© 2023 Order #XXXXX General Information General Setup Instructions - Read entire setup instruction manual prior to WARNING unpacking parts and pieces. - The setup instructions are created specifically for this configuration. - Setup instructions are laid out sequentially in steps, including exploded views with detailed explanation for assembly. -
Page 4: Side-By-Side
© 2023 Order #XXXXX Gravitee Assembly Assembly Assembly Cont’d Push pin lock into hole of connecting frame. Note: Block of pin lock will secure in groove. Side-by-Side Assembly Corner Connector 1) Frames: Place frames side-by-side with one higher than the other, then slide panel down to lock panels securely together. - Page 5 © 2023 Order #XXXXX CEI110 Frame Assembly Disassembly Slide both connectors across seam of extrusions. Tighten all knobs. Straight Connection 1) Loosen all knobs. Straight Connector When assembling frame, first attach all straight 2) Slide connectors off of one extrusion. connectors, then attach corner connectors.
- Page 6 © 2023 Order #XXXXX SEG Installation Graphic Removal Corner A Corner B Corner D Corner C Step 1 Step 2 Step 3 It is important to first insert To remove the graphic from Insert corner A. Turn edge of Repeat Step 1 for opposite Once all corners are inserted, graphic into each alternate the frame, locate the fabric...
- Page 7 © 2023 Order #XXXXX Crate Packing CRATE PACKING Crate 1 of 1...
- Page 8 © 2023 Order #XXXXX Lightbox Assembly Item Qty. Description Steps: 95”h CEI110 Vertical Extrusion Refer to the CEI110 Frame Assembly general information page. 95”h CEI110 Vertical Extrusion 68”w CEI110 Horizontal Extrusion 1) Assemble verticals [1,2] between horizontals [3,4] using corner connectors. 68”w CEI110 Horizontal Extrusion 2) Attach Base Plate [5] to lower corner of assembled frame.
- Page 9 © 2023 Order #XXXXX Backwall Assembly Item Qty. Description Steps: 11.5”w x 95”h Gravitee Panel Refer to the Gravitee Assembly general information page. 95”h Gravitee Corner Post 38”w x 95”h Gravitee Panel w/ S44 1) Assemble Gravitee panels & posts [1] through [6] 95”h Gravitee Corner Post in numerical order as shown.
- Page 10 © 2023 Order #XXXXX SEG Graphics Steps: V4 Connector 1) Attach Lightbox vertical [1] to Gravitee post [6] using bolts & V4 connectors. See V4 Connector detail. S lide V4 connector into groove of closet 2) Apply SEG graphics & blocker to backwall as shown. extrusion;...
- Page 11 © 2023 Order #XXXXX Backwall Attachments Item Qty. Description Steps: 38”w x 11”d Shelf w/ Z41 extrusions 1) Attach Shelves to vertical extrusions in Gravitee panel [3]. Shelf Attachment detail. Note: Shelves attach through SEG graphic. Shelf Attachment Insert locks into groove of vertical extrusion &...
- Page 12 © 2023 Order #XXXXX MOD-1700C Counter Assembly Item Qty. Description Steps: 1) Assemble CEI110 extrusions [1,1A,2,2A], inserting 1,1A 46.25” CEI110 Horizontal Extrusion 2,2A 37.5” CEI110 Vertical Extrusion 2-piece Sintra light blocker. See CEI110 Frame Assembly sheet for instruction. 3,3A 37.5” S44 Vertical Extrusion 2) Connect lights and transformer.
- Page 13 © 2023 Order #XXXXX MOD-1700C Counter Assembly (cont’d) Frame Attachment Steps: 1) Attach assembled frame to verticals [3] and [3A]. Attach frame to Frame Attachment detail. connector on 2) Install SEG graphic to front of assembled frame. vertical extrusion, SEG Graphic Installation detail.
Need help?
Do you have a question about the gravitee GK-1018 and is the answer not in the manual?
Questions and answers