Related Manuals for Hans Grohe Ecostat 1001 SL 13241 1 Series
Summary of Contents for Hans Grohe Ecostat 1001 SL 13241 1 Series
- Page 1 Installation Instructions / Warranty Ecostat 1001 SL 13241XX1 Ecostat 1001 SL 13261XX1...
-
Page 2: Technical Data
13241XX1 13261XX1 Technical Data Operating pressure: max. 145 psi Recommended operating pressure: 14.5 - 72 psi Hot water temperature: 120° F - 140° F* Rate of flow at 45 psi 5.3 gpm Protection against back siphonage provided by check valves in the hot and cold inlets and on the handshower outlet. -
Page 3: Installation
Rough in Install ½" NPT female fittings, recessed ³⁄₁₆" behind the surface of the finished wall, for the hot and cold water supplies. The fittings should be 5⅞" apart on center. For proper operation of the thermostatic mixer, the hot supply must be on the left and the cold supply must be on the right. - Page 4 They should extend 1⅜" outside the surface of the finished wall. 1⅜" Seal the wall around the offset adapters with waterproof sealant. Failure to seal the wall can lead to water damage. Position the valve over the offset adapters (1). Secure the valve to the adapters by rotating the nuts clockwise (2).
- Page 5 Justify the Thermostatic Mixer Handle Turn the water on. Turn the thermostatic mixer handle until the output water is 100°F. Turn the water off. Remove the screw cover. Remove the handle and safety set.
- Page 6 Reinstall the safety set so that it is oriented as shown in the diagram. Reinstall the handle with the override button at the 12:00 position. Reset the High Temperature Limit Stop The high temperature limit stop may be reset to comply with local plumbing codes.
- Page 7 Turn the water on. Turn the thermostatic mixer stem until the output water is the desired high temperature (usually 110°F). Turn the water off. Replace the high temperature limit stop ring so that the tooth is against the stop. Replace the clip. Justify and install the handle.
- Page 8 Set the EcoStop (model 13261XX1 only) Remove the screw cover. Remove the volume control / diverter handle and the flow control stop. Turn the volume control stem until the flow rate is approxi- mately 2.6 gpm.
- Page 9 Install the ecostop ring so that it is oriented as shown in the diagram. Reinstall the handle and screw cover.
- Page 10 User Instructions Using the thermostatic mixer: Turn the handle to change the temperature of the water, clock- wise to make the water cooler, counter-clockwise to make the water warmer. While making the water warmer, the handle will stop when the output water is 100°F.
-
Page 11: Troubleshooting
Troubleshooting Problem Possible Cause Solution Insufficient water - Supply pressure inadequate - Check water pressure - Filters are dirty - Clean filters in front of the mixer and on the thermostat cartridge - Screen washer dirty - Clean screen washer between shower and hose Crossflow, hot water is forced into - Check valves dirty or worn... -
Page 12: Replacement Parts
Replacement Parts... - Page 13 thermoelement 4282000 shut off and diverter unit 650000 thermostatic handle 6618XX0 handle 661XX1 aerator cpl. 13485000 check valve 6737000 noise reduction 642000 offset adapters 4140001 escutcheon 6467XX1 safety set 5041000 shut off unit 414000 ecostop ring 5042000 filter packing 622000 check valve 4074000 XX = Colors...
- Page 14 Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning. Cleaning Materials for Faucets and Showers Acids are a necessary ingredient of cleaning materials for removing lime, however please pay attention to the following points when cleaning faucets and showers:...
-
Page 15: Limited Lifetime Consumer Warranty
Limited Lifetime Consumer Warranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 16, and installed in either the United States or Canada. - Page 16 Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from State to State. You may be required by law to give us a reasonable opportunity to correct or cure any failure to comply before you can bring any action in court against us under the Magnuson-Moss Warranty Act.