Table of Contents
Advertisement
EN 26
5.
EJ3.0U PA
5.5
Error Codes
5.5.1
Introduction
The error code buffer contains all detected errors since the last
time the buffer was erased. The buffer is written from left to
right, new errors are logged at the left side, and all other errors
shift one position to the right.
When an error has occurred, the error is added to the list of
errors, provided the list is not full or the error is a protection
error.
When an error occurs and the error buffer is full, then the new
error is not added, and the error buffer stays intact (history is
maintained), except when the error is a protection error.
To prevent that an occasional error stays in the list forever, the
error is removed from the list after 50+ operation hours.
When multiple errors occur (errors occurred within a short time
span), there is a high probability that there is some relation
between them.
Basically there are three kinds of errors:
•
Errors detected by the Stand-by Processor. These
errors will always lead to protection and an automatic start
of the blinking LED for the concerned error (see paragraph
"The Blinking LED Procedure"). In these cases SDM can
be used to start up (see chapter "Stepwise Start-up").
•
Errors detected by VIPER that lead to protection. In this
case the TV will go to protection and the front LED will blink
at 3 Hz. Further diagnosis via service modes is not possible
here (see also paragraph "Error Codes" -> "Error Buffer" -
> "Extra Info").
•
Errors detected by VIPER that do not lead to
protection. In this case the error can be read out via
ComPair, via the blinking LED method, or in case you have
picture, via SAM.
Table 5-3 Error code overview
Error Description
2
1
I
C1
2
2
I
C2
2
3
I
C3
2
4
I
C4
5
VIPER does not boot (hardware failure)
6
5V supply
8
1.2V DC/DC
11
3.3V DC/DC
12
12V supply
14
Supply Class D amplifiers
18
MPIF1 ref freq
21
HDMI Mux switch
25
Supply fault
32
MPIF1
34
Tuner1
37
Channel decoder
43
Hi Rate Front End
45
Columbus 1
46
Pacific 3
53
VIPER does not boot (software failure)
Service Modes, Error Codes, and Fault Finding
Error/Prot
Detected by
Device
P
VIPER
n.a.
P
VIPER
n.a.
P
Stby µP
n.a.
E
VIPER
n.a.
P
Stby µP
n.a.
P
Stby µP
n.a.
P
Stby µP
n.a.
P
Stby µP
n.a.
P
Stby µP
n.a.
P
Stby µP
E
VIPER
PNX3000
E
AD8190ACPZ
P
Stby µP
E
VIPER
PNX3000
E
VIPER
Tuner type
E
VIPER
NXT2004
E
VIPER
TDA9975
E
VIPER
PNX2015 or 2018
E
VIPER
T6TF4HFG
P
Stby µP
PNX8550
5.5.2
How to Read the Error Buffer
Use one of the following methods:
•
On screen via the SAM (only if you have a picture). E.g.:
–
00 00 00 00 00: No errors detected
–
06 00 00 00 00: Error code 6 is the last and only
detected error
–
09 06 00 00 00: Error code 6 was first detected and
error code 9 is the last detected error
•
Via the blinking LED procedure (when you have no
picture). See next paragraph.
•
Via ComPair.
5.5.3
How to Clear the Error Buffer
Use one of the following methods:
•
By activation of the "RESET ERROR BUFFER" command
in the SAM menu.
•
With a normal RC, key in sequence "MUTE" followed by
"062599" and "OK".
•
If the content of the error buffer has not changed for 50+
hours, it resets automatically.
5.5.4
Error Buffer
In case of non-intermittent faults, clear the error buffer before
you begin the repair (before clearing the buffer, write down the
content, as this history can give you significant information).
This to ensure that old error codes are no longer present.
If possible, check the entire contents of the error buffer. In
some situations, an error code is only the result of another error
code and not the actual cause (e.g., a fault in the protection
detection circuitry can also lead to a protection).
There are several mechanisms of error detection:
•
Via error bits in the status registers of ICs.
•
Via polling on I/O pins going to the stand-by processor.
•
Via sensing of analogue values on the stand-by processor.
•
Via a "not acknowledge" of an I
Take notice that some errors need more than 90 seconds
before they start blinking. So in case of problems wait 2
minutes from start-up onwards, and then check if the front LED
is blinking.
Defective module
2
I
C1_blocked
2
I
C2_blocked
2
I
C3_blocked
2
I
C4_blocked
IF I/O
Analog Front End 1
Tuner 1
HDMI
Comb filter
2
C communication
Result
Protection + 3 Hz blinking
Protection + 3 Hz blinking
Protection + 3 Hz blinking
Protection + 3 Hz blinking
Protection + Error blinking
Protection + Error blinking
Protection + Error blinking
Protection + Error blinking
Protection + Error blinking
Protection + Error blinking
Error logged
Protection + Error blinking
Error logged
Error logged
Error logged
Error logged
Error logged
Standby
Protection (after 3 minutes) + Error blinking
Advertisement
Table of Contents
