User Manual DA14AVDDECTDEVKT Quick Start Guide UM-D-005 Abstract This guide helps users evaluate Dialog Semiconductor's DA14AVDDECTDEVKT. It also shows how to set up the boards using different stacks, that is, Audio Data (AD) stacks or Voice Data (VD) stack.
Working with Smartbeat™ AVD Studio to Program Voice Conferencing System ....17 Revision History ..........................21 Figures Figure 1: DA14AVDDECTDEVKT HW Overview .................. 5 Figure 2: Segger J-Link Lite and 20-to-10 Pin Adapter with Cable ............6 Figure 3: Board Power On ........................7 Figure 4: Jumper settings for Li-Ion batteries ..................
UM-D-005 DA14AVDDECTDEVKT Quick Start Guide Terms and Definitions Audio Voice Data Cordless Voice Module Wireless Audio Module Fixed Part Portable Part Push to Talk Tour Guide Public Address Device Under Test Human Interface Device COLA Co-Located Application HostApp Hosted Application...
DA14AVDDECTDEVKT Quick Start Guide Introduction Dialog's DA14AVDDECTDEVKT is a development kit for the DA14AVDDECT module. This module is a member of the wireless module family, operating on the interference free DECT frequency band (1.9 GHz) and it can be used in hosted or embedded Audio, Voice, and Data (AVD) applications.
UM-D-005 DA14AVDDECTDEVKT Quick Start Guide Figure 2: Segger J-Link Lite and 20-to-10 Pin Adapter with Cable Table 1: Contents of the DA14AVDDECTDEVKT Box DA14AVDDECTDEVKT Included in the Box 2 × Carrier Boards 3 × MiniUSB Cable ARM debugger (Segger J-Link LITE) with ARM JTAG-20-10 1 ×...
UM-D-005 DA14AVDDECTDEVKT Quick Start Guide Figure 3: Board Power On 3.3.2 Power via Battery 3.3.2.1 Power from Li-Ion Battery The carrier boards can also be powered from Li-Ion battery pack. The board has two 3-pin connectors for Li-Ion batteries (marked blue in Figure 4).
UM-D-005 DA14AVDDECTDEVKT Quick Start Guide 3.3.2.2 Powering from NiMH Battery The carrier boards can also be powered via NiMH battery pack. The board has one standard pin header (J204) marked blue in Figure 5. Pay attention to jumper setting on J203, J201, and J4...
UM-D-005 DA14AVDDECTDEVKT Quick Start Guide Out of the box Use The carrier boards are programmed and paired so they can be used directly out of the box. The Audio Data Stack and Tour Guide application are already installed. This section uses the Tour Guide application to explain how to set up the boards.
UM-D-005 DA14AVDDECTDEVKT Quick Start Guide 2. Once the DECT link is established between FP and PP, the green LED (D16) turns OFF on both boards and the red LED (D17 in Figure 7 Figure 8) remains ON. Figure 7: Tour Guide FP in Connected Mode...
UM-D-005 DA14AVDDECTDEVKT Quick Start Guide 3. When the Tour Guide FP and PP are connected, FP will automatically start broadcasting audio. 4. Headsets can be connected via a 3.5 mm audio jack (marked red in Figure 9) to the FP carrier board and to the PP carrier board, where the user can listen to broadcasted audio.
UM-D-005 DA14AVDDECTDEVKT Quick Start Guide Embedded Use This section explains how users can reprogram the AVD module to a Public Address (PA) system or a voice conferencing system using the Smartbeat AVD Studio. To see how to install the Smartbeat AVD studio, refer to the Smartbeat AVD Studio User Manual ([1]).
UM-D-005 DA14AVDDECTDEVKT Quick Start Guide Figure 12: Create a New Project in Smartbeat AVD Studio to Program Audio Data Stack 3. Select the "WAM PA Fp" template type for Public Address FP configuration and choose a name for the project (Figure 13).
UM-D-005 DA14AVDDECTDEVKT Quick Start Guide Make sure that the Build folder has all .bat files 4. The project structure should look like Figure 14. (bc, be, and bp). Figure 14: Project Structure (Audio Data Stack) 5. Build the project by clicking on "Build All"...
UM-D-005 DA14AVDDECTDEVKT Quick Start Guide 7. Now download Stack and COLA application to the target DUT (Figure 17). Figure 17: Download Stack/Cola Application 8. If you are using the carrier boards outside of EU region, change the DECT region accordingly by...
UM-D-005 DA14AVDDECTDEVKT Quick Start Guide Figure 21: Public Address FP in Registration Mode 14. Press MUTE button during power-up to initiate the registration mode on PP. Wait until red LED (D17) starts blinking (1 sec on/1 sec off) and Green LED (D16) is constantly on. See...
UM-D-005 DA14AVDDECTDEVKT Quick Start Guide 16. In the Public Address system PP sends audio to FP. Audio connections can be done in a way similar to step in section 4.2. 17. Please refer to Audio Stack Public Address Example Application ([3]) for more details.
UM-D-005 DA14AVDDECTDEVKT Quick Start Guide Figure 24: New Project Setup (Voice Conferencing stack) 25. Make sure that the Build folder has all .bat files 5. The project structure should look like Figure (bc, be, and bp). Figure 25: Project Structure (Voice Data Stack) 6.
UM-D-005 DA14AVDDECTDEVKT Quick Start Guide Figure 26: Build Project Options (See Toolbar) 7. Click on "DUT Connection Manager" and click on "SWD" to connect to J-Link Lite debugger (Figure 27). Figure 27: DUT Connection Manager View (for SWD) 8. Now download Stack and COLA application to the target DUT (Figure 28).
UM-D-005 DA14AVDDECTDEVKT Quick Start Guide 11. Now enable the Cola (marked blue in Figure 31) and then Reset the board (marked red in Figure 31). Figure 31: Enable Cola and Reset (See Toolbar) 12. To create a new project for the PP carrier board, follow the same procedure but change the template type to "CVM STD Pp"...
Page 22
UM-D-005 DA14AVDDECTDEVKT Quick Start Guide Status Definitions Status Definition The content of this document is under review and subject to formal approval, which may result in modifications or DRAFT additions. APPROVED The content of this document has been approved for publication.