Related Manuals for Renesas DA9318
Summary of Contents for Renesas DA9318
-
Page 1: Abstract
User Manual DA9318 Direct Charging Reference Board UM-PM-022 Abstract This document describes the hardware and software used to evaluate the DA9318 direct charging reference board. -
Page 2: Table Of Contents
Power Monitor ........................8 Direct Charging ........................8 Over-Voltage Protection ......................8 Direct Charging Sequence ....................9 DA9318 Direct Charging Reference Board Hardware .............. 10 Default Link Positions and Connector Definitions ............... 11 USB Interface ........................14 5.2.1 USB Power and GUI Reset ................. 14 Power Supplies ........................ -
Page 3: Terms And Definitions
UM-PM-022 DA9318 Direct Charging Reference Board Terms and Definitions Ground Graphical User Interface Integrated Circuit JTAG Joint Test Action Group Light Emitting Diode Level Shifter On-The-Go Personal Computer Power Delivery Reverse Current Protection SAM3U USB I C Interface Serial CLock... -
Page 4: Introduction
DA9318 to be controlled via the USB port of a PC. The mini USB connection is visible on the left side of the board. When the cable is connected to the USB port of the PC the green LED (D3) is on. - Page 5 UM-PM-022 DA9318 Direct Charging Reference Board Figure 2: DA9318 Direct Charging Reference Board (329-03-D) User Manual Revision 3.2 16-Feb-2022 5 of 39 CFR0012 © 2022 Renesas Electronics...
-
Page 6: Functional Description
UM-PM-022 DA9318 Direct Charging Reference Board Functional Description During direct charging the main charger of the battery operated device is bypassed and the Dialog TA is directly connected to the battery. The difference between normal charging and direct charging is illustrated in... - Page 7 UM-PM-022 DA9318 Direct Charging Reference Board The charging statuses are communicated via LEDs. The main charger can be enabled with the nCE signal driven from the microcontroller. During direct charging the main charger is disabled. User Manual Revision 3.2 16-Feb-2022...
-
Page 8: Power Monitor
IN2OUT_MAX When the above conditions are satisfied the DA9318 can be enabled by writing CP_EN to allow for direct charging. The TA voltage is set accordingly to allow the pre-defined charge current into the battery. -
Page 9: Direct Charging Sequence
A sequence diagram for direct charging is depicted in Figure NOTE The DA9318 direct charging reference board communication to the TA is achieved using USB PD communication protocol. The sequence diagram in Figure 4 is provided for information only. Please contact support@diasemi.com... -
Page 10: Da9318 Direct Charging Reference Board Hardware
UM-PM-022 DA9318 Direct Charging Reference Board DA9318 Direct Charging Reference Board Hardware The DA9318 direct charging reference board functionality can be broken down into sections, see Figure ● ™ USB Type-C cable input, OVP switch, input connector. ● Main charger / ADCs. -
Page 11: Default Link Positions And Connector Definitions
IN sense point GND sense point SMA connector for measuring C1N (labeled as C1M) SMA connector for measuring OUT OUT connector 1-2, 3-4, 5-6 IN connector shunt to IN of DA9318 (Close) SYS sense point GND sense point OUT connector User Manual Revision 3.2... - Page 12 Important: This erases the USB IC firmware. DO NOT SHORT Load transient connector SYS connector 1-2 (Close) SCL from SAM3U connected to DA9318 3-4 (Close) SDA from SAM3U connected to DA9318 5-6 (Close) SCL from SAM3U connected to USB PD IC...
- Page 13 UM-PM-022 DA9318 Direct Charging Reference Board Reference Designator Position Function 1-2 (Close) Both sides of level shifter set to VDD_IO Level shift from AVDD to VDD_IO 1-2 (Close) nFAULT pulled up to rail selected by J56 nFAULT pulled to ground...
-
Page 14: Usb Interface
Power Supplies The DA9318 direct charging board is powered up when a power source is connected to IN (J12). IN operating voltage range is +5.5 V to +10.5 V. ● The VDD_IO voltage is generated by an on-board regulator (VR1) supplied from the +5 V USB. -
Page 15: Da9318 Direct Charging Reference Board Software
Perform raw write and read operations to all control registers on Dialog and non-Dialog ICs. ● Monitor the charging status. ● Plot the DA9318 efficiency over time with saving and zoom feature. ● Plot the main charger efficiency over time with saving and zoom feature. ●... -
Page 16: Gui Installation Step By Step Guide
UM-PM-022 DA9318 Direct Charging Reference Board 6.1.1 GUI Installation Step By Step Guide Figure 8: GUI Setup License Agreement 1. Select I accept the agreement then click Next. User Manual Revision 3.2 16-Feb-2022 16 of 39 CFR0012 © 2022 Renesas Electronics... - Page 17 UM-PM-022 DA9318 Direct Charging Reference Board Figure 9: GUI Setup Destination Location 2. Click Next. Figure 10: GUI Setup Start Menu Location User Manual Revision 3.2 16-Feb-2022 17 of 39 CFR0012 © 2022 Renesas Electronics...
- Page 18 UM-PM-022 DA9318 Direct Charging Reference Board 3. Click Next. Figure 11: GUI Setup Additional Tasks 4. Select the Create a desktop shortcut check box (if required) and click Next. User Manual Revision 3.2 16-Feb-2022 18 of 39 CFR0012 © 2022 Renesas Electronics...
- Page 19 UM-PM-022 DA9318 Direct Charging Reference Board Figure 12: GUI Setup Start Installation 5. Click Install. Figure 13: GUI Setup Finish and Launch User Manual Revision 3.2 16-Feb-2022 19 of 39 CFR0012 © 2022 Renesas Electronics...
-
Page 20: Initial Usb Connection
1. Control Panel → Devices and Printers (double-click device with yellow exclamation sign). 2. Update Driver. 3. Browse my computer for driver software. 4. Select the Driver folder location: C:\Dialog Semiconductor\Power Management\DA9318 Reference GUI\Driver. 5. If Windows warns about the driver, select Install anyway. -
Page 21: Gui Software
DA9318 Direct Charging Reference Board GUI Software Run the DA9318 Reference Board GUI software by clicking the shortcut on the appropriate item in the Start menu (All Programs → Dialog Semiconductor → Power Management → DA9318 Reference GUI). The screen shown in Figure 14 is displayed. -
Page 22: Control Widgets
● Direct Charging: This indicator will light green when the direct charger (DA9318) is enabled. ● DONE: This indicator will light green when charge cycle is complete. -
Page 23: Charge Status Indicators
UM-PM-022 DA9318 Direct Charging Reference Board 7.2.3 Charge Status Indicators The GUI indicates the following charge statuses (assuming that the TA and the battery are both connected). “State = SUSPENDED” means that the Polling is off. Figure 18: State = SUSPENDED “State = IDLE_CHARGE”... - Page 24 UM-PM-022 DA9318 Direct Charging Reference Board State = AUTO_CHARGE and Auto State = MAIN_CHARGING means that the Polling is on; the Auto Charge is set, the Main Charger is on and the Direct Charger is off. The Status Indicators window displays the following charge status: Pre-Charge, Constant-Current, Constant-Voltage, Direct Charging and DONE.
-
Page 25: Raw I/O
UM-PM-022 DA9318 Direct Charging Reference Board 7.2.4 Raw I/O The Raw I/O control sends the entered device address, register address and data on the I communications interface. If the information sent is not valid then the I C message will return NACK an error message will be displayed in the Status window. -
Page 26: Settings
UM-PM-022 DA9318 Direct Charging Reference Board Figure 27: I2C Bus Scan 7.2.7 Settings In the Options menu, click on Settings, the Settings window is displayed. The Auto Charging parameters can be configured in the Settings window. Figure 28: Settings – Auto Charging User Manual Revision 3.2... -
Page 27: Quick Start Guide
UM-PM-022 DA9318 Direct Charging Reference Board Quick Start Guide 7.3.1 Manual Charge Operation The recommended steps to manually operate the DA9318 direct charging reference board are shown below. Main Charger BATT VBUS Travel Overvoltage CC1/CC2 Adaptor (TA) Protection IC DA9318... -
Page 28: Operational Steps
3. Click the Main Charger button. The Constant-Current status indicator flags green, signaling that the main charger is enabled. 4. Enable the Direct Charger switch (the Main Charger button auto disables). Direct charging is enabled via DA9318 and the Constant- Current and Direct Charging status indicators flag green. NOTE The direct charger current can then be increased up to 6 A by first increasing the TA CC Setting to no more than 3 A;... - Page 29 Indeed, when the watchdog timer has expired, the device returns to default mode and all registers are reset to default values. When highlighted, clicking on the Clear Events switch clears all DA9318 events. When no events are flagged the switch indicates No Events.
-
Page 30: Automatic Charge Operation
Pre-charge Direct charging Constant current Constant voltage Figure 31: Overview of the Entire Charging Cycle The recommended steps to initiate an automatic charge cycle using the DA9318 direct charging reference board are shown below. User Manual Revision 3.2 16-Feb-2022 30 of 39 CFR0012 ©... -
Page 31: Customer Configuration
UM-PM-022 DA9318 Direct Charging Reference Board 7.3.2.1 Customer Configuration In the Options menu, click on Settings, the Settings window is displayed. 1. Select the VBat Main to Direct Charger handover thresholds (volts) voltage. This is the battery voltage threshold to automatically enable the direct charger. The default value is 3.3 V. -
Page 32: Operational Steps
The charge cycle (i.e. plotting the battery voltage and charge current) is shown by the Profile Plot of the Real-time Charging Performance Graphs. The main charger and DA9318 efficiency is shown by the Efficiency Plot; whereas the DA9318 die temperature is shown by the Temperature Plot. -
Page 33: Charge Cycles Examples
Once the handover battery voltage threshold is reached to enter direct charging; the main charger is disabled and the DA9318 is enabled with a target battery charge current of 5.5 A. Upon assertion of the E_VBAT_WARN event, the TA current is reduced allowing for a smaller charge current;... - Page 34 When the charge current reaches a handover charge current threshold (arbitrarily set to 0.9 A) the DA9318 is switched off and the main charger is enabled and finishes off the charge cycle. The main charger continues its fast charge and voltage regulation phase until the termination current is reach where the main charger will get disabled.
- Page 35 UM-PM-022 DA9318 Direct Charging Reference Board Example #2: 3.7 V 3600 mAH/13.86 Wh Mobile Phone Battery Figure 37 shows the automatic charge cycle of a 3.7 V 3600 mAH/13.86 Wh mobile phone battery. Figure 37: Automatic Charge Cycle – Profile Plot – 3600 mAh Battery The test conditions are shown here below: •...
- Page 36 UM-PM-022 DA9318 Direct Charging Reference Board Figure 38: Automatic Charge Cycle – Efficiency Plot – 3600 mAh Battery Figure 39: Automatic Charge Cycle – Temperature Plot – 3600 mAh Battery User Manual Revision 3.2 16-Feb-2022 36 of 39 CFR0012 © 2022 Renesas Electronics...
-
Page 37: Revision History
UM-PM-022 DA9318 Direct Charging Reference Board Revision History Revision Date Description 01-Mar-2017 Initial version. 19-Jul-2017 USP PD implemented. New 329-03-C board and GUI. 28-Nov-2017 Added automatic charge cycle section. Main charger changed to Halo Micro’s HL7018. Board revision changed 23-Jul-2018 to 329-03-D. - Page 38 UM-PM-022 DA9318 Direct Charging Reference Board Status Definitions Status Definition DRAFT The content of this document is under review and subject to formal approval, which may result in modifications or additions. APPROVED The content of this document has been approved for publication.
- Page 39 Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing.
- Page 40 Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products.