Table of Contents
Advertisement
Quick Links
Installation and
Maintenance Instructions
Screw Vacuum Pumps
COBRA BC 0100 F
Version with Variable Frequency Drive
Busch Manufacturing Korea, Ltd.
189-51, Soicheon-ro, Majang-myun
Icheon-si, Gyunggi-do, 467-813
Republic of Korea
0870751579 /
190321 / Original instructions / Subject to change without notice
Advertisement
Table of Contents
Related Manuals for BUSCH COBRA BC 0100 F
Summary of Contents for BUSCH COBRA BC 0100 F
- Page 1 Installation and Maintenance Instructions Screw Vacuum Pumps COBRA BC 0100 F Version with Variable Frequency Drive Busch Manufacturing Korea, Ltd. 189-51, Soicheon-ro, Majang-myun Icheon-si, Gyunggi-do, 467-813 Republic of Korea 0870751579 / 190321 / Original instructions / Subject to change without notice...
-
Page 2: Table Of Contents
Discharge connection ..... 10 Congratulations on your purchase of the Busch vacuum pump. With Cooling water connection ....11 watchful observation of the field’s requirements, innovation and steady... -
Page 3: Bc 0100 F Pump Description
BC 0100 F pump description Inlet connection OUT Discharge connection Electrical connection PRV Nitrogen regulating valve CWC Cooling water connections Nitrogen connections CAO Extracting ventilator Eye bolts PLC box Emergency stop button (EMO) OSG Oil sight glass ODP Oil drain plug CPC PLC connection On/ off switch/ main circuit DGR1 DGR2... -
Page 4: Product Description
Operating principle national safety regulations and that all applicable safety measures The COBRA BC 0100 F vacuum pumps are COBRA NW screw vacuum are followed. pumps with cooling water and nitrogen circuits. -
Page 5: Oil Circuit
If you have any doubts, For a correct purge execution, the shut-off valve at the inlet flange contact your Busch representative. must be closed. The purge cycle lasts about 30 min. Safety information (Programmable time in the basic parameters). -
Page 6: Noise Emission
Type 4 l If ok, check the wiring system from the terminal box motor to the KDP1 contactor. If ok, call the BUSCH Semicon service team in Equipment is energized. Energized circuits are exposed and inadvertent charge of the maintenance of the pumps. -
Page 7: Safety Interlock Description
Emergency stop Information over the lubricants Busch YLC 250 B n°.-art. 0831 131 400 (0.5l of Busch YLC 250 B ) Quantity: BC 0100 F : 0,12 l Replacement: After 16'000 h (see Maintenance chapter, page 14) Position of the pump gravity center... -
Page 8: Appliance After Warehousing
l Switch off the water and nitrogen quick connections (inlet first, then outlet) WARNING l Put the label or warning board “Maintenance processing” on or Any disassembly of the vacuum pump should only be carried out by next to the pump staff trained for this purpose. -
Page 9: Transport
Removal of the pump Transport Before starting a vacuum pump that has been stored outside the The COBRA BC vacuum pumps are tested and checked in our factory building for a while, the vacuum pump must be moved to a room with before careful packing. -
Page 10: Installation Site And Installation
NOTE: In order to ensure the fixation of the pump to the ground, it is vacuum pump. If you have any doubts, contact your Busch possible to use again the four yellow brackets that were removed at representative. -
Page 11: Cooling Water Connection
Make sure that the drive of the vacuum pump is not disturbed by Motor of screw pump COBRA BC 0100 F is connected at factory. any electric or electromagnetic interferences. If you have any... -
Page 12: Equipment Connections (With Options)
NOTE: It is easier to switch on the vacuum pump with cold oil when the intake line is not closed or when the intake flange is not covered by The information concerning the use of the Busch PLC and the Busch a rubber plate. -
Page 13: Checking The Direct Cooling
Measure the working current of the motor and save it as reference CAUTION value for all future maintenance and repair work The COBRA BC 0100 F vacuum pumps are always delivered without Recommendations on operation oil and without cooling water. -
Page 14: Switching The Vacuum Pump On/Off
Inspect the vacuum pump for oil leaks - if there are leaks, repair If this form has not been filled in completely and signed, the the vacuum pump (Busch) vacuum pump may not be dismantled. Maintenance... -
Page 15: Monthly
Make sure that the vacuum pump has been switched off and that l Drain the oil (see “Draining the oil”) it cannot be switched on again accidentally l A main inspection of the vacuum pump (Busch) l Unscrew the oil fill plug (OFP) Lock Out/ Tag Out procedure... -
Page 16: Oil Change
Oil change CAUTION DANGER Only fill in oil through the oil filler opening. l Unscrew the oil fill plug (OFP) If the vacuum pump has pumped gases that were contaminated with foreign bodies that are hazardous to health, the oil is also l Fill in oil up to the middle of the oil sight glass contaminated with these foreign bodies. -
Page 17: Overhaul
Before work begins, the operator of the vacuum pump must fill in a Busch service will only accept vacuum pumps that come with a form or a “Declaration of Decontamination” that provides completely filled in and legally binding signed form. -
Page 18: Oil Type/ Quantity
Oil type/ quantity Oil type l Make sure that the oil type corresponds to specification: Busch YLC 250 B, Art. No. 0831 131 400 (0,5 l @ 1 kg) – WARNING The use of chemically contaminated or polluted oil can lead to hazardous pump conditions which could cause personal injury. -
Page 19: Technical Data
Technical data Technical data BC 0100 F Nominal suction capacity /h (cfm) 100 (59) Ultimate pressure hPa(mbar)/ mTorr 0,01/ 7,5 Nominal motor rating Power consumption at ultimate pressure Nominal motor speed 3000 Noise level (EN ISO 2151) dB(A) <58 Ambient temperature °C (°F) 0-40 (32-104) Maximal counter pressure... -
Page 21: Eu Declaration Of Conformity
EU-Declaration of Conformity This Declaration of Conformity and the CE-mark affixed to the nameplate are valid for the machine within the Busch scope of delivery. This declaration of Conformity is issued under the sole responsibility of the manufacturer. When this machine is integrated into a superordinate machinery the manufacturer of the superordinate machinery (this can be the operating company, too) must conduct the conformity assessment process for the superordinate machine or plant, issue the Declaration of Conformity for it and affix the CE-mark. - Page 22 Note...
- Page 23 Note...
- Page 24 Busch – All over the World in Industry www.buschvacuum.com Finland Malaysia Spain Argentina Busch Malaysia Sdn Bhd. Busch Vakuumteknik Oy Busch Argentina S.R.L. Busch Ibérica S.A. 4&6, Jalan Taboh 33/22, Seksyen 33 Sinikellontie 4 Santo Domingo 3076 Pol. Ind. Coll de la Manya...