Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BUSCH COBRA BC 0601 G
Summary of Contents for BUSCH COBRA BC 0601 G
- Page 1 Instruction Manual COBRA Screw Vacuum Pumps BC 0601 G Busch Manufacturing Korea, Ltd. 189-51, Soicheon-ro, Majang-myun Icheon-si, Gyunggi-do, 467-813 Republic of Korea 0870235875/-_en / Original instructions / Modifications reserved 08/12/2020...
- Page 2 Preface 0601G NW 0090 A, PUMA WY 0700 D, COBRA BC 0601 G Preface worldwide. 0601 G – – safety, – transport, – storage, – Power connector on vacuum pump rear side – maintenance, – – troubleshooting NW 0090 A...
- Page 3 COBRA BC 0601 G IN Inlet connection OUT Discharge connection EC Electrical connections PRV Nitrogen pressure reducer CWC Cooling water connections NC Nitrogen connection CAO Extracting ventilator EB Eye bolts RC LCD PLC PLC box ESS Emergency stop switch (EMO)
- Page 4 MOT2 COBRA BC 0601 G OSG1 Oil sight glass OSG2 Oil sight glass VFD Variable frequency device MOT1 Motor MOT1 DGR 2 MOT2 Motor TS Sensor PT100 PS Inlet pressure switch PSA Pressure sensor OSG 2 DGR 1 Regulating valve, dilution gas...
-
Page 5: Product Description
COMBI of the procedure. The COBRA BC 0601 G pumps are a combination of a screw vacuum The allowed maximum inlet gas temperature depends on the inlet pump NW 0090 A (DP) and a Roots vacuum pump WY 0700 D (MB) pressure and the type of gas: the lower the inlet pressure (Pa), the higher the drawn gas temperature (TGas) can be. -
Page 6: Nitrogen System
The COBRA BC 0601 G vacuum pumps are COBRA NW screw of these lubricants, please carry out the filling (please refer to the vacuum pumps with cooling water and nitrogen circuits. various chapters of filling). Do not forget to connect the cooling water supply before the first startup. -
Page 7: Safety Stickers
It is vital that these installation and maintenance instructions are read and understood before the vacuum pump is used. If you have any doubts, please contact your local Busch representative. Safety Information The vacuum pump has been designed and manufactured in accordance BC 0601 G with the latest technical and safety standards. -
Page 8: Decommissioning Procedure
Table A5-1 of Appendix 5 (SEMI S2 guideline). Lock Out/ Tag Out procedure (Type 1 of Busch YLC 250 B, Art. No. 0831 131 400 (0,5 l ≅ 1 kg) electrical work) -
Page 9: Temporary Storage
CAUTION Only authorized personnel may carry out any dismantling on the vacuum pump. Before work begins, the operator of the vacuum pump must fill in a form or a “Declaration Regarding Contamination of Vacuum Equipment and Components” that provides information on possible dangers and appropriate measures. -
Page 10: Installation And Commissioning
NOTE: VCI is the abbreviation for “volatile corrosion inhibitor”. The NOTE: 1° (german degree = 1° dGH) = 1,78° (french degree) = 1,25 e VCI molecule is an organic corrosion inhibitor in the vapour phase. (english degree) = 17,9 mg/kg CaCO3 (american hardness) Integrated in various carriers such as film, cardboard, paper, foam, –... -
Page 11: Discharge Connection
Discharge connection In the case of long discharge lines the line cross-section should be larg er than the discharge flange to prevent a drop in the performance of the vacuum pump. If you have any doubts, contact your Busch representative. CAUTION Cooling water connection Do not put hands into the outlet aperture. -
Page 12: Installation Mounting
Oil filling The COBRA BC 0601 G vacuum pumps are generally dispatched with oil Connect the main cable on the socket, according to the following ... -
Page 13: Checking The Direct Cooling
Oil quantity [Liter] 0,12 Stop the vacuum pump and wait a few minutes Busch VF 250, Art. No. 0831 131 400 (0,5l Oil type Make sure that the oil level still lies between the MIN and MAX ≅ 1 kg) (Busch YLC 250 B) -
Page 14: Switching The Vacuum Pump On/ Off
CAUTION Make sure that the system does not leak The COBRA BC 0601 G vacuum pumps could be delivered If the system is equipped with a solenoid gate valve at the intake: without oil, without cooling water. Operation without oil will result in damage to the vacuum pump! -
Page 15: Maintenance Program
(Busch) Inspect the vacuum pump for leaks of cooling water - if there are leaks, repair the vacuum pump (Busch) CAUTION Monthly: Before maintenance work is started, a safety area of at least In the case of operation in a dusty environment: 610 [mm] around the machine must be set up. -
Page 16: Checking The Oil
A drop in the oil level indicates a There is a health hazard when changing contaminated oil. fault (see "Alarms and warnings" -> Busch PLC and Busch LCD). There is also a danger to the environment. - Page 17 Draining used oil Checking the cooling water NOTE: After switching off the vacuum pump at normal operating Checking the cooling water flow temperature wait no more than 20 minutes before the oil is drained. Check the cooling water flow regularly Make sure that the vacuum pump is switched off and cannot ...
-
Page 18: Temporary Removal From Service
During dismantling of the vacuum pump protective equipment and Busch service will only accept vacuum pumps that come with a clothing must be worn completely filled in and legally binding signed form. dispose of the vacuum pump as scrap metal Removal from service –... -
Page 19: Oil Type/ Quantity
Make sure that the oil type corresponds to specification: – Busch YLC 250 B, Art. No. 0831 131 400 (0,5 l ≅ 1 kg) WARNING The use of chemically contaminated or polluted oil can lead to hazardous pump conditions which could cause personal injury. -
Page 20: Technical Data
Technical data Technical data BC 0601 G Effective suction capacity /h (cfm) 640 (376) Ultimate pressure Torr 2 x 10 mbar 3 x 10 Nominal motor rating (50 Hz) Nominal motor rating (50 / 60 Hz) 1,8 / 2,2 Electric power capacity at ultimate 1.25 pressure Nominal motor speed... -
Page 21: Eu Declaration Of Conformity
EU-Declaration of Conformity This Declaration of Conformity and the CE-mark affixed to the nameplate are valid for the machine within the Busch scope of delivery. This declara- t ion of Conformity is issued under the sole responsibility of the manufacturer. When this machine is integrated into a superordinate machinery the m anufacturer of the superordinate machinery (this can be the operating company, too) must conduct the conformity assessment process for the supe rordinate machine or plant, issue the Declaration of Conformity for it and affix the CE-mark. - Page 22 Note...
- Page 23 Note...
- Page 24 Portugal United Arab Emirates info@busch.cl service_sales@busch.co.il busch@busch.pt sales@busch.ae China Italy Romania United Kingdom info@busch-china.com info@busch.it office@buschromania.ro sales@busch.co.uk Colombia Japan Russia info@buschvacuum.co info@busch.co.jp info@busch.ru info@buschusa.com Czech Republic Korea Singapore info@buschvacuum.cz busch@busch.co.kr sales@busch.com.sg www.buschvacuum.com 0870235875/-_en / © Busch Manufacturing Korea, Ltd .