Installation prerequisites..... 10 Congratulations on your purchase of the Busch vacuum pump. With Local installation ..... . . 10 watchful observation of the field’s requirements, innovation and steady...
COMBI of the procedure. The COBRA BC 1000 F pumps are a combination of a screw vacuum The allowed maximum inlet gas temperature depends on the inlet pump NW 0100 A (DP) and a Roots vacuum pump WY 0701 B (MB) pressure and the type of gas: the lower the inlet pressure (Pa), the higher the drawn gas temperature (TGas) can be.
0.2 bar), the purge cycle starts. – inverters Oil circuit See "Installation and Maintenance Instructions, Busch PLC and Busch Since the complete operating principle works without contact, no oil LCD (No. 0870758077)". circuit is needed in the work area.
It is vital that these installation and maintenance instructions are read and understood before the vacuum pump is used. If you have any doubts, please contact your local Busch representative. Safety information The vacuum pump has been designed and manufactured in accordance BC 1000, 2000 F with the latest technical and safety standards.
CAUTION Only authorized personnel may carry out any dismantling on the vacuum pump. Before work begins, the operator of the vacuum pump must fill in a form or a “Declaration Regarding Contamination of Vacuum Equipment and Components” that provides information on possible dangers and appropriate measures.
NOTE: VCI is the abbreviation for “volatile corrosion inhibitor”. The NOTE: 1° (german degree = 1° dGH) = 1,78° (french degree) = 1,25 e VCI molecule is an organic corrosion inhibitor in the vapour phase. (english degree) = 17,9 mg/kg CaCO3 (american hardness) Integrated in various carriers such as film, cardboard, paper, foam, Minimum flow rate: 3 - 4 l/ min for the standard version –...
In the case of long discharge lines the line cross-section should be Discharge connection larger than the discharge flange to prevent a drop in the performance of the vacuum pump. If you have any doubts, contact your Busch representative. CAUTION Cooling water connection Do not put hands into the outlet aperture.
PID Interface (9 poles) (option) Ground Power connector on vacuum pump front side The information concerning the use of the Busch PLC and the Busch LCD can be found in the Operation and Maintenance manual (Art.No. 0870758077). Connection of the lines/ pipes...
0,12 markings on the oil sight glasses If the oil level is below the MIN marking: Busch VF 250, Art. No. 0831 000 054 (0,5 l Oil type @ 1 kg) (Busch YLC 250 B) u Fill in more oil...
Caution, the operating cycle of 150 (hPa) mbar must not exceed more Drain the cooling water – than 5 min. For other applications, contact your Busch representative. - Maximum inlet pressure: 1 bar (abs). u Pull off the connections for the inlet and outlet of the cooling...
Before maintenance work is started, a safety area of at least 610 [mm] around the machine must be set up. l Inspect the vacuum pump for leaks of cooling water - if there are leaks, repair the vacuum pump (Busch) Monthly: CAUTION In the case of operation in a dusty environment: The surface temperature of the vacuum pump can exceed 50°C...
There is a health hazard when changing contaminated oil. recommended oil change intervals. A drop in the oil level indicates a fault (see "Alarms and warnings" -> Busch PLC and Busch LCD). There is also a danger to the environment.
Draining used oil Checking the cooling water NOTE: After switching off the vacuum pump at normal operating Checking the cooling water flow temperature wait no more than 20 minutes before the oil is drained. l Check the cooling water flow regularly l Make sure that the vacuum pump is switched off and cannot accidentally be switched on again If the flow drops, check for leaks...
CAUTION can be downloaded from www.buschvacuum.com. During dismantling of the vacuum pump protective equipment and Busch service will only accept vacuum pumps that come with a clothing must be worn completely filled in and legally binding signed form. u dispose of the vacuum pump as scrap metal...
Oil type/ quantity Oil type l Make sure that the oil type corresponds to specification: Busch YLC 250 B, Art. No. 0831 131 400 (0,5 l @ 1 kg) – WARNING The use of chemically contaminated or polluted oil can lead to hazardous pump conditions which could cause personal injury.
Technical data Technical data BC 1000 F Effective suction capacity /h (cfm) 930 (547) Ultimate pressure Torr 2.25 x 10 mbar 3 x 10 Nominal motor rating (50 Hz) (90 Hz) Nominal motor rating Electric power capacity at ultimate pressure kW idle mode Nominal motor speed 3000...
EU-Declaration of Conformity This Declaration of Conformity and the CE-mark affixed to the nameplate are valid for the machine within the Busch scope of delivery. This declaration of Conformity is issued under the sole responsibility of the manufacturer. When this machine is integrated into a superordinate machinery the manufacturer of the superordinate machinery (this can be the operating company, too) must conduct the conformity assessment process for the superordinate machine or plant, issue the Declaration of Conformity for it and affix the CE-mark.