Page 1
Installation and Maintenance Instructions Screw Vacuum Pumps COBRA BC 0200 F Busch Manufacturing Korea, Ltd. 189-51, Soicheon-ro, Majang-myun Icheon-si, Gyunggi-do, 467-813 Republic of Korea 0870767417/ / Original instructions / Subject to change without notice 190605...
Cooling water connection ....12 Congratulations on your purchase of the Busch vacuum pump. With Nitrogen connection ..... 12 watchful observation of the field’s requirements, innovation and steady...
If the The COBRA BC 0200 F vacuum pumps are COBRA NW screw vacuum pump has sucked in liquid, a short drying time is necessary at the end pumps with cooling water and nitrogen circuits.
If you have any doubts, A heating jacket attached to the exhaust heats the exhaust up to the li- contact your Busch representative. mit of 130°C in order to eliminate any condensate. Safety information...
Type 4 l If ok, check the wiring system from the terminal box motor to the KDP1 contactor. If ok, call the BUSCH Semicon service team in Equipment is energized. Energized circuits are exposed and inadvertent charge of the maintenance of the pumps.
POW ER Breaker Information over the lubricants Emergency Busch YLC 250 B n°.-art. 0831 131 400 (0.5l of Busch YLC 250 B) Klixon stop Quantity: BC 0200 F : 0,12 l Replacement: After 16'000 h (see Maintenance chapter, page 15)
l Switch off the customer’s power supply WARNING l Switch off the water and nitrogen quick connections (inlet first, then outlet) Any disassembly of the vacuum pump should only be carried out by l Put the label or warning board “Maintenance processing” on or staff trained for this purpose.
Lock Out/ Tag Out procedure This handbook is contained in the delivery package. l Stop the pump with the remote control (press on STOP button Storage during 10s) l Press on emergency stop button Temporary storage l Switch off the main breaker l Make sure that the intake and exhaust flanges are closed (put on l Switch off the customer’s power supply the protective caps included in the delivery package of the vacuum...
NOTE: The levelling of the pump is facilitated by the adjustment stroke Installation and start-up (~15 mm) of the four machine foots. l Make sure that the four rollers do not touch the ground Necessary installation instructions NOTE: In order to ensure the fixation of the pump to the ground, it is possible to use again the four yellow brackets that were removed at CAUTION the reception of the machine.
(this is the responsibility of the manufacturer of the Motor of screw pump COBRA BC 0200 F is connected at factory. system into which the vacuum pump is integrated according to the Declaration of Conformity)
Oil filling CAUTION The COBRA BC 0200 F vacuum pumps are always delivered without oil (see the chapter “Oil types” for information on the recommended The transformer voltage (in the electrical box) must be in accor- oils). dance with the supply voltage of the machine.
Recommendations on operation Application CAUTION The COBRA BC 0200 F vacuum pumps are always delivered without WARNING oil and without cooling water. The vacuum pump is designed for use under the conditions speci- Operation without oil will result in damage to the vacuum pump! fied here.
Maintenance CAUTION If there is a risk of frost, all the cooling water must be drained out DANGER of the vacuum pump if the pump is shut down for a longer period of time! In case the vacuum pump has conveyed gases that have been contaminated with foreign materials that are dangerous to health, Drain the cooling water –...
Drain the oil (see “Draining the oil”) l Fill in oil up to the middle of the oil sight glass l A main inspection of the vacuum pump (Busch) l Make sure that the oil level lies between the MIN and MAX...
Make sure that the drain plug has been fitted properly and that they do not leak If dark oil similar to the example shown is observed, you have to contact the Busch Customer Service without delay. CAUTION Oil change Only fill in oil through the oil filler opening.
Oil type/ quantity Oil type l Make sure that the oil type corresponds to specification: Busch YLC 250 B, Art. No. 0831 131 400 (0,5 l @ 1 kg) – WARNING The use of chemically contaminated or polluted oil can lead to hazardous pump conditions which could cause personal injury.
Technical data Technical data BC 0200 F Nominal suction capacity Ultimate pressure hPa(mbar)/ mTorr 0,01/ 7,5 Nominal motor rating Power consumption at ultimate pressure Nominal motor speed 4570 Noise level (EN ISO 2151) dB(A) <60 Ambient temperature °C (°F) 10 - 40 (32 - 104) Maximal counter pressure Discharge Cooling water requirement...
EU-Declaration of Conformity This Declaration of Conformity and the CE-mark affixed to the nameplate are valid for the machine within the Busch scope of delivery. This declara- tion of Conformity is issued under the sole responsibility of the manufacturer. When this machine is integrated into a superordinate machinery the manufacturer of the superordinate machinery (this can be the operating company, too) must conduct the conformity assessment process for the superordinate machine or plant, issue the Declaration of Conformity for it and affix the CE-mark.
Page 24
Busch – All over the World in Industry www.buschvacuum.com Finland Malaysia Spain Argentina Busch Malaysia Sdn Bhd. Busch Vakuumteknik Oy Busch Argentina S.R.L. Busch Ibérica S.A. 4&6, Jalan Taboh 33/22, Seksyen 33 Sinikellontie 4 Santo Domingo 3076 Pol. Ind. Coll de la Manya...