Advertisement
Quick Links
Break Away Fitting for Demersible
IMPORTANT!
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
change product without prior written notification.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
INSTALLATION MANUAL
83 West Drive, Bramton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
Pumps
®
Models: BAF-8
P/N: 082110A
Form No. 133727 Rev. B
Advertisement
Related Manuals for Crane Deming BAF-8
Summary of Contents for Crane Deming BAF-8
- Page 1 Read all instructions in this manual before operating pump. As a result of Crane Pumps & Systems, Inc., constant product improvement program, product changes may occur. As such Crane Pumps & Systems reserves the right to change product without prior written notification. A Crane Co. Company...
-
Page 2: Safety First
Other brand and product names are trademarks or registered trademarks of their respective holders. ® Deming is a registered trademark of Crane Pumps & Systems, Inc. 1998, 2002, 4/06, 9/06 Alteration Rights Reserved... -
Page 3: Section: C Installation
Whenever the guide pipe lengths exceed 13 feet, an Service Department in Piqua, Ohio, telephone optional intermediate guide rail support bracket should (937) 778-8947 or Crane Pumps & Systems Canada Inc., Bramton, Ontario (905) 457-6223. be used (see Figure 5 and 6). The intermediate guide rail support brackets may be supported from the vertical discharge pipe. - Page 4 inches (mm) Figure 1...
-
Page 5: Section E: Replacement Parts
D-2.2) Intermediate Support : These instructions apply to all Deming pumps with a 125 lb. flange horizontal discharge on volute. All parts for To replace Guide Plug(s) on Intermediate support standard and non-sparking BAF’s are the same except for (reference Figure 5), remove cotter pin (3D) and cap screw moveable assembly. - Page 6 Figure 2...
- Page 7 Figure 3...
- Page 8 Figure 4...
- Page 9 Figure 5...
- Page 10 PARTS LIST BAF-8 p/n 082110A ITEM QTY. PART NO. DESCRIPTION 079680A Stationary Elbow Assembly 079326A Slide, Moveable Assembly 079907 Upper Guide Bracket 079909 Plug, 2.88” O.D. x 2.00” Lg Rubber 079910 Threaded Disk, 2.88” x .38” Steel 079911 Hex Hd Screw, 7/16-14 x 3.25” Lg Steel 002917 Cotter Pin, 1.25”...
- Page 11 Figure 6 8” Intermediate Support Bracket p/n 085034G ITEM QTY. PART NO. DESCRIPTION 085134F Intermediate Support Assembly 079906G Guide Rail Bracket Assembly Stainless 079909 Guide Plug, 2.88” O.D. x 2.00” Lg. Rubber 1-169-6 Hex Hd. Screw, .437-14 x 3.25” Lg. 18-8 SS 085136F Bolt, U, ⅝-11, 12.00”...
-
Page 12: Warranty Registration
IMPORTANT! WARRANTY REGISTRATION Your product is covered by a warranty: www.cranepumps.com/downloadables/CATALOGS_OIPMs/Warranty/24MonthWarranty.pdf If you have a claim under the provisions of the warranty, contact your local Crane Pumps & Systems, Inc. Distributor.
Need help?
Do you have a question about the Deming BAF-8 and is the answer not in the manual?
Questions and answers