Table of Contents
Advertisement
Quick Links
INSTALLATION and OPERATION MANUAL
Solids Handling Submersible Pump
#5 Frame
This product may be covered by one or more of the following patents and other patent(s) pending: US Patent 8,128,360
IMPORTANT!
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
change product without prior written notification.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
Series: 7365N
4M
Monovane Pumps
75HP, 1750RPM
4D
Dual Vane Pumps
75 - 100HP, 1750RPM
6V
Vortex Pumps
75 - 100HP, 1750RPM
50 - 75HP, 1150RPM
40HP, 870RPM
83 West Drive, Bramton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
6M
Monovane Pumps
75 - 100HP, 1750RPM
6D
Dual Vane Pumps
75 - 100HP, 1750RPM
8V
Vortex Pumps
50 - 100HP, 1150RPM
40 - 50HP, 870RPM
8D
Dual Vane Pumps
75HP, 1750RPM
8T
Tri Vane Pumps
75 - 150HP, 1750RPM
50 - 100HP, 1150RPM
40 - 50HP, 870RPM
10D
Dual Vane Pumps
50 - 100HP, 1150RPM
40 - 50HP, 870RPM
Form No. 142699-Rev. G
Advertisement
Table of Contents
Related Manuals for Crane DEMING 7365N Series
Summary of Contents for Crane DEMING 7365N Series
- Page 1 Read all instructions in this manual before operating pump. As a result of Crane Pumps & Systems, Inc., constant product improvement program, product changes may occur. As such Crane Pumps & Systems reserves the right to change product without prior written notification. A Crane Co. Company...
-
Page 2: Table Of Contents
WARRANTY REGISTRATION ......................24 START-UP REPORT ........................ 25 - 26 Other brand and product names are trademarks or registered trademarks of their respective holders. ® Deming is a registered trademark of Crane Pumps & Systems, Inc 2018 Alteration Rights Reserved... -
Page 3: Safety First
IMPORTANT! - Crane Pumps & Systems, Inc. is not responsible for losses, injury, or death resulting from a WARNING! - DO NOT pump hazardous materials failure to observe these safety precautions, misuse or (flammable, caustic, etc.) unless the pump is specifically... -
Page 4: General Information
Crane Pumps & Systems, Inc., Service Department fitting discharge system designed to allow the submersible in Piqua, Ohio, telephone (937) 778-8947 or Crane Pumps wastewater pump to be installed or removed without & Systems Canada, in Brampton, Ontario, (905) 457-6223. - Page 5 B-3) Liquid Level Controls: B-4.1) Electrical Connections: It is recommended to use a liquid level control system When the electrical connections are made, the lead wires that allows the on and off point to be separated by at least from the power cable should be stripped so that the ground twelve inches.
- Page 10 8 AWG, 6 AWG, 2 AWG 0 AWG / 18/5 - Dual Cord THREE PHASE 460-575 VOLT AC THREE PHASE 460-575 VOLT AC Power Cable Motor Lead ID Power Cable Motor Lead ID Green (Ground) Green Green (Ground) Green Black Black White White...
- Page 11 WIRING DIAGRAM FIGURE 4 B-4.3) Overload Protection: Current sensing overloads must be provided in the pump A manual momentary start switch is required to prevent control panel and should be properly sized for the full load the automatic restarting of the motor when the thermostat current of the pump.
-
Page 12: Start-Up Operation
Return a f. A motor starter and overload system. copy to Crane Pumps & Systems and store the second in the control panel or with the pump manual. It is important... -
Page 13: Preventative Maintenance
As the motor and seal chamber are oil-filled, no lubrication or and create a hazard. Overfilling oil voids other maintenance is required, and generally Crane Pumps & warranty. Systems will give very reliable service and can be expected E-1.3) Pressure Test:... - Page 14 E-2.2) Reassembly: Stationary Member To install impeller (6), apply a thin film of oil to motor shaft Polished Face Out and slide impeller straight onto shaft, keeping keyways lined up. Drive key (7) into keyway. Thread cap screw (8) and washer (8A) into shaft and torque to 45 ft. lbs. Rotate impeller to check for binding.
-
Page 15: Replacement Parts
SECTION: F REPLACEMENT PARTS F-1 ORDERING REPLACEMENT PARTS: When ordering replacement parts, ALWAYS furnish the following information: 1. Pump serial number and date code. (Paragraph F-4) 2. Pump model number. (Paragraph F-3) 3. Pump part number. (Paragraph F-2) 4. Part description. 5. -
Page 16: Trouble Shooting
TROUBLE SHOOTING CAUTION ! Always disconnect the pump from the electrical power source before handling. If the system fails to operate properly, carefully read instructions and perform maintenance recommendations. If operating problems persist, the following chart may be of assistance in identifying and correcting them: MATCH “CAUSE”... -
Page 17: Recommended Minimum Suction Clearance (Fig. 9)
DIM. ‘A’ MODEL INCHES NUMBER (MM) ACCESS COVER (SUPPLIED BY OTHERS) 3.00 (76.2) GUIDE RAIL CAP SUPPLIED 3VRA WITH BAF MODELS 3.50 (88.9) INTERMEDIATE SUPPORT ASSY 3.75 (OPTIONAL) REFER (95.3) TO SECTION C-3 2" PIPE GUIDE RAILS (SUPPLIED BY OTHERS) 4.00 (101.6) 4VHA... -
Page 18: Cross Sections (Fig. 8 & 9)
CROSS SECTIONS Vortex FIGURE 10 Enclosed FIGURE 9... -
Page 19: Exploded View (Fig. 10)
EXPLODED VIEWS FIGURE 11... -
Page 20: Parts List
PARTS LIST ITEM PART NO. DESCRIPTION MATERIAL 136284 Screw, SHCS, M12 x 1.75 x 25 300 SS 138312 Pin, Spring, .13 x .20 300 SS 138315 Seal, Mech, 2.88” C/CE/B 138315SD Seal, Mech, 2.88” SC/SC/B See Table Impeller Ductile Iron Q21-20-J8 Key, .25 x .25 x 1.50”... - Page 21 SH Pump ‘Plug and Play’ Removeable Cord Assemblies Length Part No. Cord Size Max Amps Cord O.D. (feet) 138317XF 8/4 - 18/4 59.0 1.12in ± .02in (28.4mm ± .5mm) 138317XJ 8/4 - 18/4 59.0 1.12in ± .02in (28.4mm ± .5mm) 138317XL 8/4 - 18/4 59.0...
- Page 22 Notes...
-
Page 23: Warranty
Crane Pumps & Systems, Inc. Distributor. RETURNED GOODS RETURN OF MERCHANDISE REQUIRES A “RETURNED GOODS AUTHORIZATION”. CONTACT YOUR LOCAL CRANE PUMPS & SYSTEMS, INC. DISTRIBUTOR. Products Returned Must Be Cleaned, Sanitized, Or Decontaminated As Necessary Prior To Shipment, To Insure That Employees Will Not Be Exposed To Health Hazards In Handling Said Material.
Need help?
Do you have a question about the DEMING 7365N Series and is the answer not in the manual?
Questions and answers