Table of Contents
Advertisement
Quick Links
TITAN INDUSTRIES
735 INDUSTRIAL LOOP ROAD
NEW LONDON WI 54961
920-982-6600
800-558-3616 Toll Free
920-982-7750 FAX
E-MAIL: sales@titanconveyors.com
Website: www.titanconveyors.com
MODEL 526
Conveyor
INSTALLATION, MAINTENANCE AND
PARTS MANUAL
For additional copies of this manual,
please visit our website at
www.titanconveyors.com.
Go to Replacement Parts/Accessories
and select Maintenance Manuals. You can then
select the manual for your model conveyor.
SERIAL NO.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Titan 526
Summary of Contents for Titan 526
- Page 1 735 INDUSTRIAL LOOP ROAD NEW LONDON WI 54961 920-982-6600 800-558-3616 Toll Free 920-982-7750 FAX E-MAIL: sales@titanconveyors.com Website: www.titanconveyors.com MODEL 526 Conveyor INSTALLATION, MAINTENANCE AND PARTS MANUAL For additional copies of this manual, please visit our website at www.titanconveyors.com. Go to Replacement Parts/Accessories and select Maintenance Manuals.
- Page 2 (D) No representative of TITAN has been conferred with any authority to waive, alter, vary or add to the terms of warranty state herein, without prior authorization in writing executed by an officer of the company.
-
Page 3: Table Of Contents
This will require you to call a Titan salesperson prior to your sending back the item to get a RGA number and receive instructions on how to return the item. Other information needed at this time would be your original purchase order number, Titan serial number, job number or invoice number. - Page 4 Safety The Safety alert symbol is used with the signal words DANGER, WARNING and CAUTION to alert you to safety messages. They are used in safety decals on the unit and with proper operation and procedures in this manual. They alert you to the existence and relative degree of hazards. Understand the safety message.
-
Page 5: Introduction
Titan at 920-982-6600. I. RECEIVING Upon delivery of your Titan conveyor, check the packing slip or bill of lading accompanying the unit. If any components are missing, contact Titan IMMEDIATELY with a description of the missing components along with the conveyor serial number(s). -
Page 6: Frame Assembly
If the frame placement has not been shown Titan recommends that the drive section be placed approximately in the center of the overall conveyor length. This is especially important for conveyors over 30 foot in length. -
Page 7: Component Checklist
FIGURE 3 WARNING REPLACE CHAIN GUARDS AFTER CHAIN CONNECTION IS COMPLETE. COMPONENT CHECKLIST Prior to start up use the following list to double check the conveyor components MOTOR Have a qualified electrician ensure the motor is wired correctly for your power source. Check that motor is securely fastened to the reducer or motorbase. - Page 8 III. MAINTENANCE MOTORS CLEANING - All motors should be kept free of dirt and grease accumulations. Open motors should be periodically vacuumed to remove dust and dirt from the windings. VENTILATION - For best results motors should be operated in an area where adequate ventilation is available.
- Page 9 2. VENTILATION - During normal operation gear reducers build up heat and pressure that MUST be vented to protect the seals and gears. If not installed at Titan, a brass vent plug contained in a small plastic bag, will be put in a box or larger bag along with fasteners sent loose for use during field installation. Remove the top most drain plug (refer to FIGURE 5 for the position of your reducer) and install the vent plug securely in place.
- Page 10 ONLY compatible polyglycol lubricants should be used. Contact the factory for more information. 5. TEMPERATURE - Most Titan units are supplied with worm gear reducers. These units may run at temperatures between 100 degrees to 200 degrees F. (Higher temperatures are especially common during start up).
- Page 11 SAE 40 120 degrees - 140 degrees F SAE 50 REMEMBER - ALL GUARDS AND BOTTOM PANS, IF PROVIDED, MUST BE REPLACED BEFORE RUNNING CONVEYOR. TITAN INDUSTRIES IS NOT DANGER RESPONSIBLE FOR INJURIES CAUSED BY NOT COMPLYING WITH SAFETY INSTRUCTIONS.
- Page 12 MODEL 526 CHAIN TO CHAIN DRIVEN LIVE ROLLER CONVEYOR OPTIONAL SIDE DRIVE FRAME WELDMENT SOFT START (OPT) H. D. SUPPORT CHAIN GUARD REDUCER SMILE BRACKET ROLLER ASSEMBLY MOTOR BASE KNEE BRACE (OPT) DRIVE GUARD SUPPORT FOOT HEX SHAFT CHAIN LOOP SIDE MT.
- Page 13 MODEL 526 C.D.L.R. POP-UP TRANSFER-SINGLE DIRECTION "T" FRAME SUPPORT ANGLE FRAME WELDMENT-SIDE POP-UP TRANSFER CHAIN FRAME WELDMENT-END POP-UP SPROCKET KEY DRIVE BASE WEAR PAD-BOX FRAME REDUCER POP-UP TAIL SHAFT UP STOP BOLT MOTOR KEY IDLER SPK'T. SHAFT COLLAR POP-UP BOX FRAME...
- Page 14 NEW LONDON WI 54961 920-982-6600 800-558-3616 Toll Free 920-982-7750 FAX E-MAIL: sales@titanconveyors.com Website: www.titanconveyors.com Contact Your Distributor or Titan Directly for Further Information on Other Titan Conveyor Products Slider bed conveyors Floor to Floor belt conveyors parts conveyors ...
Need help?
Do you have a question about the 526 and is the answer not in the manual?
Questions and answers