Why is my Silvercrest PD-8871 air conditioner not blowing cold air?

If your Silvercrest PD-8871 air conditioner is not cooling sufficiently, consider the following:Doors and windows are not closed properly: Close doors and windows.Heat sources in the room: Remove all heat sources if possible.Hot air outlet hose is not connected or blocked: Connect the hot air outlet hose 13 or clean it.Temperature setting is too high: Adjust the temperature setting.Air inlets are blocked: Clean the air inlets 5, 9. For more information, see page 44 of the manual.

How do I set up the Silvercrest PD-8871 air conditioner for the first time?

To set up your Silvercrest PD-8871 air conditioner for the first time, follow these steps: Check Product and Delivery Contents Be very careful when opening the packaging. Remove the product from its packaging. Check that all delivery contents are complete. If the product or individual parts are visibly damaged, do not use it and contact the manufacturer via the service address. Set up the ProductPlace the product on an easily accessible, level, dry, heat-resistant and stable surface to minimize vibration and noise.The product is fitted with castors 4. Do not roll it over objects and, if necessary, protect fragile floor coverings.Ensure the product is located near a properly installed grounded power socket.Make sure the air inlets 5/9 and air outlets 3/7 are always free of obstructions.Maintain a minimum distance of 30 cm between the product and any obstacles. Attach the Window SealingClean the windows and window frames thoroughly to ensure they are free from dust and grease.Cut the hook and loop fastener 12b to the dimensions of your window and attach it around the entire window frame. Do not attach it to the glass.Secure the window fabric 12a to the hook and loop fastener 12b, starting with the narrow part and working from the middle.Screw the hose connection (window) 14 and the hose connection (air conditioner) 15 to each end of the hot air outlet hose 13 by pulling its ends apart.Push the hose connection (air conditioner) 15 into the rail provided on the back air outlet 7.Open the zip on the window fabric 12a by approximately 50 cm. Insert the hot air outlet hose 13 of the air conditioner unit into the opening, then close the zip to secure the hose. Insert/Replace Batteries in the Remote ControlOpen the battery compartment cover 29 on the back of the remote control 11.Insert 2 AAA (LR03) type batteries 28 into the compartment, ensuring the correct polarity (+ or -).Reattach the battery compartment cover 29. Initial OperationPlug the mains plug 10 into a properly installed grounded power socket. Do not use extension leads or multi-plugs.Point the remote control 11 in the direction of the signal receiver 24 and ensure there are no obstacles.You can adjust the direction of the air flow by moving the lever on the ventilation slots 2.

What do the different error codes on the Silvercrest PD-8871 display mean?

The Silvercrest PD-8871 display shows the following error codes:Error code E0: This indicates that the room temperature sensor is defective. In this case, you should contact customer service.Error code E2: This means the water tank is full. To resolve this, you need to empty the water tank. For more information, see page 44 of the manual.

What is the best way to clean the air filter of the Silvercrest PD-8871?

To clean the air filter of your Silvercrest PD-8871, follow these steps:Clean the air filter 6 every 2 weeks or when it is visibly dirty.Unplug the mains plug 10 before cleaning.Drain the water tank completely.Wipe the product with a slightly damp cloth, then allow all parts to dry completely.Remove the air filter 6 from the housing.Clean the filter with lukewarm water (max. 40 °C) and some neutral detergent.Let the filter air dry completely (without direct sunlight).Put the air filter 6 back in the housing. For more information, see page 45 of the manual.

What is the recommended room size for the Silvercrest PD-8871 air conditioner?

The Silvercrest PD-8871 air conditioner is suitable for rooms with a minimum floor space of 4 m² and a maximum room volume of 60 m³. For more information, see pages 28, 30, 35 and 36 of the manual.

How do I drain the water reservoir of the Silvercrest PD-8871?

The integrated water tank fills when the product cannot evaporate moisture quickly enough (e.g., at low room temperature and high humidity) or when operating in dehumidification mode. When the tank is full, the water tank indicator (W.F) 16 lights up, the error code "E2" 19 is shown, and the product stops operating. To drain the water tank, follow these steps:Switch off the product and remove the mains plug 10 from the socket.Pull the hose connector 15 off the back air outlet 7 and remove the hot air outlet hose 13 from the product.To empty the water tank, use a floor cloth or a flat bowl that can absorb/accommodate 0.5 L of water.Pull the drain plug 8 (as well as the inner plug beneath it) out of the opening and allow the water to drain.Insert both drain plugs 8 back into the opening properly.Once the product has been connected to the power supply and the hot air outlet hose 13 has been reattached, it can resume operation.

How do I use the timer function on the Silvercrest PD-8871?

The Silvercrest PD-8871 has a timer function for both automatic switch-on and automatic switch-off (sleep timer). Automatic Switch-on:When the product is off, push the TIMER button 12.The display 19 will flash, and the timer indicator 18 will light up.Use the TEMP- button 25 or TEMP+ button 26 to set the timer for 1–24 hours. The set time will flash on the display 19.Push the TIMER button 21 again to confirm the set time. If no further entry is made within about 10 seconds, the timer will be cancelled.If necessary, select an operating mode (COOL, DEHUM, or FAN) using the MODE button 23.The timer will begin counting down, and the product will turn on automatically when the set time is reached.To cancel the timer function, press the TIMER button 21 once.Automatic Switch-off (Sleep Timer): When the product is on, push the TIMER button 21. Use the TEMP- button 25 or TEMP+ button 26 to set the timer for 1–24 hours. The set time will flash on the display 19. Push the TIMER button 21 again to confirm the set time. If no further entry is made within about 10 seconds, the timer will be cancelled. The timer will begin counting down, and the product will turn off automatically when the set time is reached. To cancel the timer function, press the TIMER button 21 once.

Does the Silvercrest PD-8871 air conditioner have a fan-only mode?

Yes, the Silvercrest PD-8871 air conditioner has a fan-only mode. The product has 3 operating modes: cooling, dehumidification, and fan mode. To use the fan mode:Press the POWER button 27 to switch on the product.Press the MODE button 23 repeatedly until the mode indicator 20 shows FAN.The product is now in fan mode. The temperature is automatically set to 25 °C and shown on the display 19, but cannot be set manually.Push the SPEED button 22 to adjust the fan speed. The fan speed indicator 17 shows the selected speed (HIGH or LOW).

How do I troubleshoot if the remote control for my Silvercrest PD-8871 isn't working?

If the remote control for your Silvercrest PD-8871 is not working, consider the following troubleshooting steps:Check Batteries: Ensure the 2 AAA (LR03) type batteries 28 are inserted with the correct polarity (+ or -) and are not drained. Only use the specified battery type. Clean the contacts on the battery and in the compartment with a dry, lint-free cloth. Do not mix old and new batteries.Remote Control Alignment: Point the remote control 11 directly towards the signal receiver 24 on the unit, and ensure there are no obstacles between them. For more information, see pages 37, 38, 39 and 40 of the manual.

How can I reduce the noise level of my Silvercrest PD-8871?

To reduce the noise level of your Silvercrest PD-8871, ensure the product is standing on as level and flat a surface as possible. The noise level of the device is 65 dB(A).

What is the power consumption of the Silvercrest PD-8871 air conditioner?

The power consumption of the Silvercrest PD-8871 air conditioner is 785 W. In standby mode, the power consumption is 0.5 W. The nominal power consumption in cooling mode is 0.769 kW.

Silvercrest PD-8871 Operation And Safety Notes

Deutsch

English

Français

Dutch

Polski

Čeština

Slovenčina

Español

Dansk

Italiano

Available languages

Quick Links

Chapters

Frequently Asked Questions (11)

Need help?

Questions and answers

Related Manuals for Silvercrest PD-8871

Summary of Contents for Silvercrest PD-8871