Page 1
SGP-500 Fully Pneumatic Piston Filling Machine SGP Series Operation Manual (Please read it carefully before using the machine!) ATTENTION: Machine must be completely torn down, cleaned, sanitized, and lubricated with H3 food grade lubricant prior to use. A recommended lubricant has been provided.
Instruction of Fully Pneumatic Filling Machine of SGP Series Table of Contents Chapter 1 Overview ..................3 1-1 Overview ....................3 1-2 Features ....................3 1-3 Parameters ................... 3 1-4 Working Principle ................. 3 1-5 Working Process .................. 4 1-6 Available Range ................... 4 1-7 Introduction to Parts and Specifications ..........
Its reasonable layout enables you to easily disassemble, safely operate, and easily clean the filler. Due to a total lack of electrical compenents, this filler can be used safely in a wide array of hazardous or moist environments. 1-3 Parameters Item SGP-500 Available range Cream/Paste/Liquid Cream 50-500ml Filling range...
Instruction of Fully Pneumatic Filling Machine of SGP Series 1-5 Working Process Open the inlet valve, adjust the working air pressure and select the working status (automatic or semiautomatic). During the operation, the rotary cylinder linkage is turned (opens a path towards the front while sealing towards the top), the fill head cylinder moves upwards to open the discharge valve, the piston cylinder actuates to move the piston forward, which dispenses material for filling ( the speed can be adjusted by the “Behind”...
Instruction of Fully Pneumatic Filling Machine of SGP Series 1-7 Introduction to Parts and Specifications Hopper Main air cylinder Adjustable lock handle/sensor Protective covering Crossmember Foot pedal Air regulator Air gauge 10. Behind valve 11. Front valve 12. In-line air filter 13.
Instruction of Fully Pneumatic Filling Machine of SGP Series Chapter 2 Operation Instruction 2-1 Preparation Precautions The inlet air pressure should be 0.5-0.8Mpa and the working air pressure should be 0.4-0.5 Mpa. Keep all appendages clear of moving parts during operation. Filling amount troubleshooting Adjust the filling amount as follows: Put materials to be filled into the container.
Instruction of Fully Pneumatic Filling Machine of SGP Series 2-2 Operation Method Connect the air source and slide the air inlet collar towards the machine. Check whether the air pressure meter is in the specified range (roughly reading in the “12-3 o’clock” range). If not, draw the air pressure knob outwards to unlock, rotate the pressure regulator knob until the pressure is in the specified range (0.4- 0.5Mpa) and push the knob back in to lock.
Instruction of Fully Pneumatic Filling Machine of SGP Series 2-3 Fault Analysis and Troubleshooting Symptom Analysis Troubleshooting Check whether the air pressure collar is open Open it Check whether source open Open it (compressor) Check whether the value on air pressure meter is Adjust it to 0.4-0.5MPa in the correct range Check whether there is leakage on any air fittings or...
Instruction of Fully Pneumatic Filling Machine of SGP Series 2-4 Safety Instruction You can use soap and warm water to clean the machine. Fill hopper with cleaning agent and water; cycle until discharge is clear of any product; fill hopper with clean water and cycle until water is clear Never use sharp tools on any parts surface when cleaning the internal parts and install the parts when they are dry.
Instruction of Fully Pneumatic Filling Machine of SGP Series Chapter 3 Rotary Breakdown Assembly 3-1 Machine Specification – O-ring List Machine comes standard with buna o-rings Piston: 5x35 Rotary: 3.5x38 Fill Head: (Several Pieces) Nozzle: 3x25 Plunger: 3x18 Shaft: 3x5.5 Upper, Outer: 3x25 Upper, Inner: 2.5x13 Rotary to chamber gasket: 2 inch TC (tri-clamp)
Need help?
Do you have a question about the SGP-500 and is the answer not in the manual?
Questions and answers