1. Manuals
  2. Brands
  3. Supero Manuals
  4. Chassis
  5. SC812 Series
  6. Installation manual

Supero SC812 Series Installation Manual

Supermicro sc812 chassis: install guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
S
®
UPER
The SC812/SC812L Chassis Series
Installation Guide
Rev. 1.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SC812 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Supero SC812 Series

Summary of Contents for Supero SC812 Series

  • Page 1 ® UPER The SC812/SC812L Chassis Series Installation Guide Rev. 1.0...

  • Page 2: Table Of Contents

    Chapter 2: Installation Procedures ... 2-1 Section 1: Installing components into the Chassis ... 2-1 A. Removing the Top Cover from the SC812/SC812L Chassis ... 2-1 B-1. Removing and Installing the Disk Drive ... 2-2 B-2. Removing and Installing the Hard Drive Disks ... 2-3 C-1.

  • Page 3: Chapter I: Introduction

    Chapter 1: Introduction A. Front Panel Connectors Front Panel LED Indicators (See Section B Below.) CD-ROM Floppy HDD Tray HDD Tray HDD Tray RJ45 (COM) Port USB 2.0 Ports (x2) B. Front Panel LED Indicators Power Button Reset Button PWR LED HDD LED 6./7.

  • Page 4: Back Panel Connectors

    All images and layouts shown in this manual were based upon the latest chassis Revision available at the time of publishing of this manual. The chassis you’ve received may or may not look exactly the same as the graphics shown in this manual.

  • Page 5: Chapter 2: Installation Procedures

    2. Slide the top cover out from the chassis as shown below: 1. Press the release but- tons 3. You can now lift the side cover up and off the chassis. Chapter 2: Installation Procedures 2. Slide the top cover out...

  • Page 6: B-1. Removing And Installing The Disk Drive

    Procedures: 1. Press the release tab on the right side of the disk drive to release the disk drive handle. 2. Pull the disk drive handle outwards and remove it from the chassis. 2b. Remove the disk drive. 2a. Pull the handle outwards.

  • Page 7: B-2. Removing And Installing The Hard Drive Disks

    3. Once the HDD drive tray is detached from the chassis, remove the two screws on each side of the drive tray to separate the HDD from the drive tray as shown below.

  • Page 8: C-1. Rail Installation

    1.An inner fixed chassis rail (A) that is attached to the chassis. 2. An outer fixed rack rail (B) which is affixed to the rack. 3. A sliding rail guide (C) that is sandwiched between the chassis rail and the rack rail. The sliding guide should remain attached to the outer fixed rack rail (B).

  • Page 9: C-2. Installing Chassis Rails

    2. Press the locking tab to release the inner rail from its locking position and pull out the inner rail from the rail assembly. (*The inner rails are to be attached to the chassis and the outer rails are to be installed in the rack.) Pull out the Inner...
  • Page 10 SC812/SC812L Chassis User's Guide 3. Locate the five holes on each side of the chassis and locate the five corresponding holes on each of the inner rail. 4. Attach an inner rail to each side of the chassis and secure the inner rail to the chassis by inserting five Type G screws through the holes on the chassis and the inner rail.

  • Page 11: D-1. Rack Installation For The Traditional 1U Design

    Chapter 2: Installation Procedures D-1 Rack Installation for the Traditional 1U Design After you have installed the inner rails on the chassis, you are ready to install the outer rails of rail assemblies to the rack. (* The rails are designed to fit in the racks with the depth of 28" to 33".)
  • Page 12 SC812/SC812L Chassis User's Guide 7. Slide the SC812/SC812L chassis into the rack as shown below: (The SC812/SC812L may not slide into the rack smoothly or easily when installed the first time. However, some adjustment to the slide assemblies might be needed for easy installation.) 8.

  • Page 13: D-2. Rack Installation For The Open-Rack Design

    Chapter 2: Installation Procedures D-2 Rack Installation for the Open-Rack Design After you have installed the inner rails on the chassis, you are ready to install the outer rails of rail assemblies to the rack. (* The rails are designed to fit in the racks with the depth of 28" to 33".)
  • Page 14 SC812/SC812L Chassis User's Guide 3. Attach the front (-short) bracket to the front end of the rack, and secure it to the rack with two Type H screws and Type I washers as shown below. 4. Attach the rear (-long) bracket to the rear end of the rack, and secure it to the rack with two Type H screws and Type I washers as shown below.
  • Page 15 5. Measure the depth of your rack and adjust the length of the rails accord- ingly. Then, secure the rails to the chassis with Type G screws. 6. Slide the inner rails which are attached to the chassis to into the outer rails on the rack.

  • Page 16: Windows Os

    6) Click “Next” 2 times, uncheck both “Floppy disk drives” and “CD-ROM drives”. Then, select the item- “Specify a location,” and choose “Next”. 7) Click on “Browse” and choose D drive or wherever Supermicro Setup CD is in. 8) Choose “Qlogic” folder and click on “Open”.

This manual is also suitable for:

Sc812l seriesSc812l-280uSc812l-420cSc812l-520Sc812l-520cSc812l-520u ... Show all

Table of Contents