General Pipe Cleaners Speedrooter 92 S92-450 Operating Instructions Manual
  1. Manuals
  2. Brands
  3. General Pipe Cleaners Manuals
  4. Pipe cleaners
  5. Speedrooter 92 S92-450
  6. Operating instructions manual

General Pipe Cleaners Speedrooter 92 S92-450 Operating Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Your Speedrooter 92R is designed
to give you years of trouble-free, profita-
ble service.
However, no machine is
better than its operator.
Read, understand and follow all
safety warnings and instructions provid-
ed with the product. Failure to follow the
warnings and instructions may result in
electric shock and/or serious injury.
Save all warnings and instructions for
future reference.
SAVE THESE INSTRUCTIONS!
Speedrooter 92R
Operating Instructions
For 3" through 10"
(75mm—250mm)
®

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Speedrooter 92 S92-450 and is the answer not in the manual?

Questions and answers

Related Manuals for General Pipe Cleaners Speedrooter 92 S92-450

Summary of Contents for General Pipe Cleaners Speedrooter 92 S92-450

  • Page 1 ® Speedrooter 92R Operating Instructions For 3” through 10” (75mm—250mm) Your Speedrooter 92R is designed to give you years of trouble-free, profita- ble service. However, no machine is better than its operator. Read, understand and follow all safety warnings and instructions provid- ed with the product.

  • Page 2: General Safety Rules

    ® Speedrooter 92R GENERAL SAFETY RULES Electric shock resulting death can occur if you plug this machine into an improper- ly wired outlet. If the ground wire is electrified, you can be electrocuted by just touching the machine, even when the power switch is off.

  • Page 3: General Power Tool Safety Warnings

    ® Speedrooter 92R GENERAL POWER TOOL SAFETY WARNINGS* 3. Prevent unintentional starting. Ensure the switch is in the off- position before connecting to power source and/or BATTERY WARNING pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the Read all safety warnings, instructions, illustrations and specifica- switch on invites accidents.

  • Page 4: Specific Safety Information

    ® Speedrooter 92R 8. Only use the drain cleaner for the recommended drain sizes. 9. Keep handles and grasping surfaces dry, clean and free from Using the wrong size drain cleaner can lead to twisting, kinking or oil and grease. Slippery handles and grasping surfaces do not breaking of the cable and may result in personal injury.

  • Page 5: Ground Fault Circuit Interrupter (Gfci)

    ® Speedrooter 92R Ground Fault Circuit Interrupter (GFCI) Cable Application Chart (Table 1) Your machine is equipped with a ground fault circuit interrupter, which protects you against shock if a short circuit should occur. Check that Cable Size Pipe Size Typical Applications receptacle is properly grounded.

  • Page 6: Operation

    ® Speedrooter 92R OPERATION INSTALLING THE GUIDE TUBE HOLDER SET-UP To install the Guide Tube Holder on The Metro, follow the as- sembly shown in the diagram below. Place the Guide Tube Hold- MAKE SURE THE MOTOR SWITCH IS IN er on the mounting knob, then thread it onto the bolt to secure THE ‘OFF’...
  • Page 7 ® Speedrooter 92R OPERATION Hint: It's often helpful to have a small stream of water running in Before stepping on the foot pedal, place the guide tube and cable the line to wash the cuttings away while the machine is in operation into the drain opening.

  • Page 8: Special Operations

    ® Speedrooter 92R HOW TO REMOVE DRUM SPECIAL OPERATIONS DISCONNECT MACHINE FROM POWER SOURCE BEFORE REMOVING DRUM FROM MACHINE! IF CABLE GETS CAUGHT IN LINE The motor can be reversed for a few seconds at a time to free the Remove belt guard by loosening the knob above the motor and cable if it gets caught in line.

  • Page 9: Maintenance

    ® Speedrooter 92R MAINTENANCE Slide the V-Belt (62”) over the drum and hang it from the slip clutch. Push down on the motor enough to slide the V-Belt onto the drum. DISCONNECT MACHINE FROM POWER SOURCE Pull about 12” of cable out beyond the front post. BEFORE PERFORMING MAINTENANCE! Slide the Flexitube, spring end first, onto the cable and into the To keep your machine operating smoothly, it is essential that all bear-...
  • Page 10 ® Speedrooter 92R DAMAGED ROLLER TANGLED CABLE If a cable loops over itself in the drum, it will not feed properly. Re- Excessive use may wear a roller to the point of failure. It is recom- move and reload the cable to restore function. If the cable kinks, it is mended that all three rollers be replaced at the same time (Cat # PO- evidence of abuse and results from the use of too much pressure or 703).
  • Page 11 ® Speedrooter 92R TROUBLE SHOOTING GUIDE (Table 3) Problem Probable Cause Solution Cable kinks or breaks. Operator forcing the cable. Do not force the cable. Let the cutter do the work. Too much slack between machine and Allow no more than two feet between machine and drain. drain.
  • Page 12 ® Speedrooter 92R General Wire Spring Co. 1101 Thompson Avenue McKees Rocks, PA 15136 412-771-6300 www.drainbrain.com © General Wire Spring Co. 2023 C-92ROI-0423...

This manual is also suitable for:

Speedrooter 92rT5219

Table of Contents