Subscribe to Our Youtube Channel
Related Manuals for DUSK Windsor
Summary of Contents for DUSK Windsor
-
Page 2: Assembly Tip
Important Assembly Tip Before you begin, it's best to identify all of the parts and fittings to build your ottoman bed frame. We advise laying these out on the floor to check you have everything, and to familiarise yourself with all of the parts and fittings before building. Top Tip We recommend that you build your new ottoman bed frame in the room you'd like it to be located. - Page 5 Parts Check List Box No No. Parts List Parts List Box No Headboard Box 1 Plastic Corner Bracket 4pcs Box 1 Box 1 Angle Corner Bracket 4pcs Box 1 Footboard Side Rail with Lift Mechanism - LH Box 2 Holding Block Box 1 1pcs Side Rail with Lift Mechanism - RH...
- Page 7 Step 2: Attaching the Bolts to the Headboard & Footboard Before tightening the bolts, please ensure the bed frame is square...
- Page 8 Step 3: WRONG CORRECT Attaching the Left & Right Side Rails to the Headboard & Footboard Page 7 ： Before tighteing the bolts, please ensure the bed frame is square...
- Page 9 6WHS4: $WWDFKLQJWKH6LGH5DLOVWRWKH+HDGERDUG )RRWERDUGXVLQJ the Angle Corner Brackets 2 pcs 8 pcs...
- Page 10 6WHS5:6HFXULQJWKHOHIW 5LJKW6LGH5DLOVWRWKH/LIWLQJ0HFKDQLVP 2 pcs Leave the ottoman bed frame in an elevated position. Page 8 Step 6: Attaching the Fabric Base & Legs...
- Page 11 Fit the fabric base along the velcro on the base of bed frame. Make sure the side of the fabric base with holes is attached to the footboard and attach the legs through the 2 holes to the footboard.
- Page 12 Step 7: Attaching the Rear Ottoman Metal Frame to the Side Rails Page 9...
- Page 15 Step 11: Attaching the Slats & Strap to the Ottoman Metal Frame Side Slat Caps Double/King 26/30 pcs Double/King 13/15 Centre Slat Caps Push down firmly on the Slat Caps into the pre-drilled holes on the Ottoman Metal Frame. It is recommended to push the Centre Slat Caps into position before pushing down on the Side Slat Caps.
-
Page 16: Care And Maintenance
Care and Maintenance Here are some good tips to keep your new ottoman bed frame in tip-top condition. Cleaning To clean your new ottoman bed frame, we advise using a damp cloth if the fabric is dusty or a low suction vacuum. - Page 18 Gas strut/piston best use: · Use caution when operating - always use two hands. · Only attempt to close the ottoman frame, once the mattress has been placed on the frame. · The thicker side of the cylinder should be above the thinner side - this will increase longevity ofthe part. ·...
- Page 20 efore you begin, it's best to identify all of the parts and fittings to build your ottoman bed frame. We advise laying these out on the floor to check you have everything, and to familiarise yourself with all of the parts and fittings before building. We recommend that you build your new ottoman bed frame in the room you'd like it to be located.
- Page 23 Parts Check List Parts List Box No No. Parts List Box No Headboard Box 1 Plastic Corner Bracket 4pcs Box 1 Footboard Box 1 Angle Corner Bracket 4pcs Box 1 Side Rail with Lift Mechanism - LH Box 2 Holding Block 3pcs Box 1 Box 2...
- Page 26 Attaching the Bolts to the Headboard & Footboard NB: Before tightening the bolts, please ensure the bed frame is square...
- Page 27 Attaching the Left & Right Side Rails to the Headboard & Footboard WRONG CORRECT ： Before tighteing the bolts, please ensure the bed frame is square...
- Page 28 6WHS4: $WWDFKLQJWKH6LGH5DLOVWRWKH+HDGERDUG )RRWERDUGXVLQJ the Angle Corner Brackets 6 pcs 8 pcs...
- Page 29 6WHS5:6HFXULQJWKHOHIW 5LJKW6LGH5DLOVWRWKH/LIWLQJ0HFKDQLVP 2 pcs Leave the ottoman bed frame in an elevated position. Page 8...
- Page 30 Step 6: $WWDFKLQJWKH)DEULF%DVH /HJV Fit the fabric base along the velcro on the base of bed frame. Make sure the side of the fabric base with 2 holes is attached to the footboard and attach the legs through the 2 holes to the footboard.
- Page 31 Step 7: $WWDFKLQJWKH5HDU2WWRPDQ0HWDO)UDPHWRWKH6LGH5DLOV 3DJH9...
- Page 32 Step 8: ttaching the Horizontal Support Rails to the Left & Right Side Rails 6pcs...
- Page 33 Step 9: Attaching the Centre Support Rail to the Rear Ottoman Metal Frame Page 10...
- Page 35 Step 11: S ts & Strap Ottoman Metal F 30pcs Side Slat Caps Super King Centre Slat Caps Super King 30pcs Push down firmly on the Slat Caps into the pre-drilled holes on the Ottoman Metal Frame. It is recommended to push the Centre Slat Caps into position before pushing down on the Side Slat Caps Attach the Strap (12) to the Center Ottoman Metal...
- Page 36 good ottoman frame ottoman frame the or abrasive frame, fabric will ap differently fabric ay also exposure.
- Page 38 Gas strut/piston best use: · Use caution when operating - always use two hands. · Only attempt to close the ottoman frame, once the mattress has been placed on the frame. · The thicker side of the cylinder should be above the thinner side - this will increase longevity ofthe part. ·...
Need help?
Do you have a question about the Windsor and is the answer not in the manual?
Questions and answers
Once the metal frame is installed, how do you push down the frame to close
To close the metal frame of the DUSK Windsor, get assistance from a second person. Both individuals should apply equal pressure from each side of the footboard until the frame closes. This may require more force than expected. Stop applying pressure if the metal frame begins to warp and contact customer service if this occurs.
This answer is automatically generated