Setting A Disc To Protect - Toshiba RDXV60KB Owner's Manual

E3TK6BD_EN.book Page 44 Wednesday, February 17, 2010 10:18 AM
To move a title:
1) Go to the dubbing list, then select a title using
[K L]. Then press [ENTER OK].
2) Select "Move" using [K L], then press
[ENTER OK].
3) Select a desired insert point using [K L], then
press [ENTER OK].
To erase all the titles in the dubbing title list:
1) Select "Delete All" in the dubbing menu using
[K L], then press [ENTER OK].
2) Select "Yes" using [K L], then press
[ENTER OK]. Final confirmation message will
appear.
3) Select "Yes" using [K L], then press
[ENTER OK].
• To go back and forth between dubbing menu and
dubbing list, use [0 1].
7
After adding all the titles you want, select
"Dubbing Start" in the dubbing menu using
[K L], then press [ENTER OK].
8
Select a desired recording mode using [0 1],
then press [ENTER OK].
e.g.) HDD DVD
Please select REC MODE.
High XP SP LP EP
Dubbing Titles
e.g.) HDD VCR
Please select REC MODE.
SP LP
Confirmation message will appear.
• Depending on the dubbing direction, the available
recording mode varies.
• When dubbing from HDD to DVD, you can select "High"
to perform the high speed dubbing (refer to "Recording
Mode for Dubbing" on page 41 for more details).
9
Select "Yes" using [K L], then press
[ENTER OK].
Start Dubbing?
Yes
No
If dubbing continues when timer recording starts, the next
display will appear.
Timer Recording is in standby.
Start Dubbing?
Yes
No
Dubbing will start.
• It may take awhile to prepare for the dubbing.
To stop the dubbing in progress:
Press [STOP C] on the front panel.
Press [STOP C] for 2 seconds on the remote control.
For "HDD to VCR" or "DVD to VCR", press
[STOP EJECT C A] on the front panel.
Note
• Dubbing will be cancelled 2 minutes before starting timer
recording.
44
EN
3
4
5
SLP Auto
500 MB
3000 MB
• Dubbing will start where the tape is stopped.
• After starting dubbing, the picture may be distorted because
• Dubbing will be cancelled 2 minutes before starting timer
• The device mode change is available only between HDD

Setting a Disc to Protect

To prevent accidental over-recording, editing or erasing of
recordings, you can protect them using "Setup" menu.
Insert a recordable disc.
1
2
3
VCR to HDD / DVD
Select "VCR HDD" / "VCR
[K L], then press [ENTER OK].
e.g.) VCR HDD
HDD A DVD
DVD A HDD
HDD A VCR
VCR A HDD
DVD A VCR
VCR A DVD
Select a desired recording mode using [0 1],
then press [ENTER OK].
Please select REC MODE.
XP SP LP EP
Confirmation message will appear.
Select "Yes" using [K L], then press
[ENTER OK].
Start Dubbing?
Yes
No
If dubbing continues when timer recording starts, the next
display will appear.
Timer Recording is in standby.
Start Dubbing?
Yes
No
Dubbing will start.
• It may take awhile to prepare for the dubbing.
To stop the dubbing in progress:
Press [STOP C] on the front panel.
Press [STOP C] for 2 seconds on the remote control.
Note
of the digital tracking function. This is not a malfunction. Be
advised to play back the videotape until the picture is
stabilised, then set the starting point at which you want to
start recording, and start dubbing.
recording.
and DVD during the videotape to the HDD / DVD dubbing.
VR
DVD-RW DVD-RW DVD-RW DVD+RW DVD+RW DVD+RW DVD+R DVD+R DVD+R
In stop mode, press [SETUP].
Select "DVD Menu" using [K L], then press
[ENTER OK].
Select "Disc Protect OFF
then press [ENTER OK].
DVD" using
SLP
3000 MB
ON" using [K L],