. GENERAL INFORMATION Bet & Win 250 SERIAL NUMBER Vehicle Identification Serial Number Location of Frame Serial Number Location of Engine Serial Number www.PlanDeGraissage.org...
. GENERAL INFORMATION Bet & Win 250 Cooling Type Water cooling SPECIFICATIONS Name & Model No. SH50CA Motorcycle Name & Type B&W250 Overall length 2000mm Overall width 750mm Air cleaner type & No Paper element, wet Overall height 1140mm Fuel capacity 10.5 liters Wheel base 1435mm...
. GENERAL INFORMATION Bet & Win 250 SERVICE PRECAUTIONS n Apply or add designated greases and lubricants to the specified lubrication points. n Make sure to install new gaskets, O-rings, circlips, cotter pins, etc. when reassembling. n After reassembly, check all parts for proper tightening and operation.
Page 5
. GENERAL INFORMATION Bet & Win 250 n If the fuse is burned out, find the cause and n The connector shall be inserted repair it. Replace it with a new one completely. according to the specified capacity. n If the double connector has a lock, lock it at the correct position.
Page 6
. GENERAL INFORMATION Bet & Win 250 n After clamping, check each wire to make n Route harnesses so they are neither sure it is secure. pulled tight nor have excessive slack. Do not pull too tight n Do not squeeze wires against the weld or its clamp.
Page 7
. GENERAL INFORMATION Bet & Win 250 n After routing, check that the wire harnesses n Symbols: are not twisted or kinked. The following symbols represent the servicing methods and cautions included in this service manual. : Apply engine oil to the specified points.
. GENERAL INFORMATION Bet & Win 250 LUBRICATION POINTS ENGINE Lubrication Points Lubricant Valve guide/valve stem movable part •Genuine KYM CO Engine Oil (SAE15W-40) Camshaft protruding surface •API SE, SF or SG Egnine Oil Valve rocker arm friction surface Camshaft drive chain Cylinder lock bolt and nut Piston surroundings and piston ring grooves Piston pin surroundings...
Page 11
. GENERAL INFORMATION Bet & Win 250 FRAME The following is the lubrication points for the frame. Use general purpose grease for parts not listed. Apply clean engine oil or grease to cables and movable parts not specified. This will avoid abnormal noise and rise the durability of the motorcycle.
. GENERAL INFORMATION Bet & Win 250 CABLE & HARNESS ROUTING Rear Brake Master Cylinder Front Brake Fluid Tube Front Stop Switch Rear Stop Switch Throttle Cable Speedometer Cable Pressure Type Radiator Cap Radiator Air Vent Tube Radiator Horn 1-11 www.PlanDeGraissage.org...
Page 13
. GENERAL INFORMATION Bet & Win 250 Ignition Switch Radiator Air Fuel Tank Vent Tube Breather Tube Fuel Filler Fuel Tank Inlet Tube Water Hose Front Brake Fluid Tube Water Hoses 1-12 www.PlanDeGraissage.org...
Page 14
. GENERAL INFORMATION Bet & Win 250 Reserve Tank Cap Throttle Cable Radiator Air Fuel Filler Vent Tube Rear Brake Fluid Speedometer Cable Tube Fuel Tank Inlet Tube Fuel Tank Breather Tube Water Hose Wire Harness Fuel Tank Throttle Cable 1-13 www.PlanDeGraissage.org...
Page 15
. GENERAL INFORMATION Bet & Win 250 Oil Vapor Fuel Tube Recovery Tube T.P.S Wire Ignition Coil Thermostat Carburetor Starter Motor Starter Relay CDI Unit Regulator/ Rectifier Battery (+) Cable Battery (-) Cable Fuse Box 1-14 www.PlanDeGraissage.org...
Page 16
. GENERAL INFORMATION Bet & Win 250 Throttle Cable Ignition Coil Auto Bystarter Spark Plug Cap Fuel Pump Vacuum Tube Carburetor Oil Vapor Recovery Tube Fuel Tube Thermostat Starter Relay T.P.S Fuel Tube Fuel Pump Vacuum Tube Wire Harness Fuel Pump Ignition Coil Oil Vapor...
. GENERAL INFORMATION Bet & Win 250 TROUBLESHOOTING ENGINE WILL NOT START OR IS HARD TO START Inspection/Adjustment Probable Cause Symptom Check if fuel reaches carburetor by loosening drain screw ÅEmpty fuel tank ÇClogged carburetor fuel inlet tube, vacuum tube or fuel tube ÉClogged auto fuel valve Fuel reaches Fuel does not...
Page 19
. GENERAL INFORMATION Bet & Win 250 ENGINE LACKS POWER Inspection/Adjustment Symptom Probable Cause Start engine and accelerate ÅClogged air cleaner lightly for observation ÇRestricted fuel flow ÉClogged fuel line between fuel tank and carburetor Engine speed Engine speed does ÑClogged exhaust muffler increases not increase...
Page 20
. GENERAL INFORMATION Bet & Win 250 POOR PERFORMANCE (ESPECIALLY AT IDLE AND LOW SPEEDS) Inspection/Adjustment Symptom Probable Cause Check ignition timing ÅFaulty CDI unit Correct timing Incorrect timing ÇFaulty A.C. generator Check carburetor pilot screw adjustment ÅMixture too rich (turn screw Incorrectly adjusted Correctly adjusted out)
Page 21
. GENERAL INFORMATION Bet & Win 250 POOR PERFORMANCE (AT HIGH SPEED) Inspection/Adjustment Symptom Probable Cause Check ignition timing ÅFaulty CDI unit Correct timing Incorrect timing ÇFaulty A.C. generator Check valve clearance ÅImproperly adjusted valve Correctly adjusted Incorrectly adjusted clearance ÇWorn valve seat Check fuel pump for fuel supply...
Page 22
. GENERAL INFORMATION Bet & Win 250 ENGINE NOISE Symptom Probable Cause ÅValve clearance too large Valve noise ÇWorn camshaft lobe ÅWorn piston rings ÇWorn piston pin and connecting rod Piston noise small end ÉExcessive carbon build-up in combustion chamber ÅDamaged cam chain tensioner ÇWorn cam gear teeth Cam chain noise...
Page 23
. GENERAL INFORMATION Bet & Win 250 CLUTCH, DRIVE AND DRIVEN PULLEYS Symptom Probable Cause ÅWorn or slipping drive belt ÇBroken ramp plate ÉBroken drive face spring Engine starts but ÑSeparated clutch lining motor-cycle does not ÖDamaged driven pulley shaft splines move ÜDamaged final gear áSeized final gear...
Page 24
. GENERAL INFORMATION Bet & Win 250 STARTER MOTOR 1. Starter motor won‘t turn Symptom Inspection/Adjustment Probable Cause Check operation of stop switch by ÅBurned out fuse applying brake ÇWeak or dead battery Stoplight does not ÉFaulty stop switch Stoplight comes come on ÑLoose or disconnected Check battery...
Page 25
. GENERAL INFORMATION Bet & Win 250 closed NO SPARK AT SPARK PLUG Inspection/Adjustment Symptom Probable Cause Replace with a new spark plug and inspect again Good spark Weak or no spark ÅFaulty spark plug Check spark plug cap and high-tension wire for looseness Not loose Loose...
Page 26
. GENERAL INFORMATION Bet & Win 250 POOR CHARGING (BATTERY OVER DISCHARGING OR OVERCHARGING) Undercharging Inspection/Adjustment Symptom Probable Cause Start engine and test limit voltage of battery terminals ÅFaulty AC generator Voltage does not Normal voltage ÇFaulty regulator/rectifier increase ÉFaulty battery Measure resistance between AC generator coil terminals...
Page 27
. GENERAL INFORMATION Bet & Win 250 FUEL GAUGE 1. Pointer does not register correctly (Ignition switch ON) Inspection/Adjustment Symptom Probable Cause Check battery circuit by operating turn ÅBurned out fuse signals ÇWeak or dead battery Signals operate Signals dim, remain ÉFaulty ignition switch properly on or don‘t...
Page 28
. GENERAL INFORMATION Bet & Win 250 STEERING HANDLEBAR DOES NOT TRACK STRAIGHT Symptom Probable Cause (Front and rear tire pressures are normal) ÅSteering stem nut too tight Steering is heavy ÇBroken steering steel balls ÅExcessive wheel bearing play Front or rear wheel is ÇBent rim wobbling ÉLoose axle nut...
. EXHAUST MUFFLER/FRAME COVERS Bet & Win 250 SERVICE INFORMATION GENERAL INSTRUCTIONS • When removing frame covers, use care not to pull them by force because the cover joint claws may be damaged. • Make sure to route cables and harnesses according to the Cable & Harness Routing. TORQUE VALUES Exhaust muffler lock bolt 34.3N-m...
. EXHAUST MUFFLER/FRAME COVERS Bet & Win 250 Bolts/Nuts FRAME COVERS REMOVAL REAR CARRIER & HAND RAIL REMOVAL Remove the met-in box: First remove the two bolts and two nuts attaching the met-in box. Remove the battery and fuse. Remove the met-in box. Fuse Hex Bolts Remove the hand rail right and left lock hex...
Page 33
. EXHAUST MUFFLER/FRAME COVERS Bet & Win 250 Remove the midst screw attaching the right and left side covers. Side Cover Screws Remove the screws attaching the right and left side covers. Screw Screws FLOOR BOARD REMOVAL Remove the floor mat. Remove the center cover.
Page 34
. EXHAUST MUFFLER/FRAME COVERS Bet & Win 250 FRONT UPPER COVER REMOVAL Remove the four screws on the back of the front upper cover. Remove the front upper cover. The installation sequence is the reverse of removal. Screws Screws FRONT LOWER COVER REMOVAL First remove the front upper cover.
. EXHAUST MUFFLER/FRAME COVERS Bet & Win 250 HANDLEBAR COVER REMOVAL First remove the seven screws attaching the handlebar back cover. Remove the handlebar back cover. Screws Bolts BOTTOM COVER REMOVAL Remove the side stand. Remove the four bolts attaching the bottom cover.
. INSPECTION/ADJUSTMENT Bet & Win 250 SERVICE INFORMATION GENERAL WARNING •Before running the engine, make sure that the working area is well ventilated. Never run the engine in a closed area. The exhaust contains poisonous carbon monoxide gas, which may cause death to people. •Gasoline is extremely flammable and is explosive under some conditions.
In the interest of safety, we recommend these items be serviced only by an authorized • KYMCO motorcycle dealer. Note: 1. For higher odometer readings, repeat at the frequency interval established here. 2. Service more frequently when riding in dusty or rainy areas.
. INSPECTION/ADJUSTMENT Bet & Win 250 FUEL LINE/FUEL FILTER Remove the center cover. Check the fuel lines and replace any parts, which show signs of deterioration, damage or leakage. Check for dirty or clogged fuel filter and replace with a new one if it is clogged. *...
. INSPECTION/ADJUSTMENT Bet & Win 250 Oil Dipstick ENGINE OIL OIL LEVEL INSPECTION Stop the engine and support the motorcycle upright on level ground. Wait for 2_ 3 minutes and check the oil level with the dipstick. Do not screw in the dipstick when making this check.
. INSPECTION/ADJUSTMENT Bet & Win 250 Screws AIR CLEANER Remove the eight air cleaner case cover screws and the cover. Air Cleaner Case Cover Air Cleaner Element Remove the air cleaner element. Check the element and replace it if it is excessively dirty or damaged.
. INSPECTION/ADJUSTMENT Bet & Win 250 Bolts VALVE CLEARANCE * • Inspect and adjust valve clearance while the engine is cold (below 35℃ ). Remove the cylinder head cover. Cylinder Head Cover Turn the A.C. generator flywheel to the top dead center (TDC) on the compression stroke so that the “T”...
. INSPECTION/ADJUSTMENT Bet & Win 250 CYLINDER COMPRESSION Warm up the engine before compression test. Remove the center cover and spark plug cap. Remove the spark plug. Insert a compression gauge. Open the throttle valves fully and pushes the starter button to test the compression. Compression: 16.5±2kg/cm_ If the compression is low, check for the following:...
. INSPECTION/ADJUSTMENT Bet & Win 250 Oil Check Bolt Hole/Oil Filler FINAL REDUCTION GEAR OIL * • Place the motorcycle on its main stand on level ground. Stop the engine and remove the oil checks bolt. The oil level shall be at the oil check blowhole.
. INSPECTION/ADJUSTMENT Bet & Win 250 HEADLIGHT AIM Turn the ignition switch ON. Turn on the headlight switch. Adjust the headlight aim by turning the headlight aim adjusting bolt. Headlight Aim Adjusting Bolt CLUTCH SHOE WEAR Start the engine and check the clutch operation by increasing the engine speed gradually.
. INSPECTION/ADJUSTMENT Bet & Win 250 Coolant capacity : 1165cc Radiator capacity : 825cc Reserve tank capacity : 340cc Start the engine and check if there are no bubbles in the coolant and the coolant level is stable. Reinstall the radiator cap. If there are bubbles in the coolant, bleed air from the system.
. INSPECTION/ADJUSTMENT Bet & Win 250 NUTS/BOLTS/FASTENERS Check all important chassis nuts and bolts for looseness. Tighten them to their specified torque values if any looseness is found. WHEELS/TIRES Check the tires for cuts, imbedded nails or other damages. Check the tire pressure. *...
Page 48
. LUBRICATION SYSTEM Bet & Win 250 __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ LUBRICATION SYSTEM __________________________________________________________________________________ LUBRICATION SYSTEM DIAGRAM-------------------------------- 4-1 SERVICE INFORMATION -------------------------------------------- 4-2 TROUBLESHOOTING ------------------------------------------------- 4-2 ENGINE OIL/OIL FILTER -------------------------------------------- 4-3 OIL PUMP REMOVAL------------------------------------------------- 4-4 OIL PUMP DISASSEMBLY ------------------------------------------- 4-4 OIL PUMP INSPECTION ---------------------------------------------- 4-5 OIL PUMP ASSEMBLY------------------------------------------------ 4-5 OIL PUMP INSTALLATION------------------------------------------ 4-6...
. LUBRICATION SYSTEM Bet & Win 250 SERVICE INFORMATION GENERAL INSTRUCTIONS • The maintenance of lubrication system can be performed with the engine installed in the frame. • Drain the coolant before starting any operations. • Use care when removing and installing the oil pump not to allow dust and foreign matters to enter the engine and oil line.
. LUBRICATION SYSTEM Bet & Win 250 ENGINE OIL/OIL FILTER * Place the motorcycle upright on • level ground for engine oil level check. Run the engine for 2_ • minutes and check the oil level after the engine is stopped for 2_ 3 minutes.
. LUBRICATION SYSTEM Bet & Win 250 Bolts OIL PUMP REMOVAL First drain the coolant. Remove the right crankcase cover. ( 10-3) Remove the A.C. generator starter driven gear. ( 10-4) Remove the attaching bolt and oil separator cover. Oil Separator Cover Oil Pump Driven Gear Pry the circlip off and remove the oil pump driven gear, then remove the oil pump drive...
. LUBRICATION SYSTEM Bet & Win 250 Pump Body Outer Rotor OIL PUMP INSPECTION Measure the pump body-to-outer rotor clearance. Service Limit: 0.25mm replace if over Outer Rotor Measure the inner rotor-to-outer rotor clearance. Service Limit: 0.20mm replace if over Inner Rotor Measure the rotor end-to-pump body clearance.
. LUBRICATION SYSTEM Bet & Win 250 Pump Hole Screw Cover Install the pump cover by aligning the hole in the cover with the dowel pin. Tighten the screw to secure the pump cover. Make sure that the pump shaft rotates freely without binding.
Page 55
. ENGINE REMOVAL/INSTALLATION Bet & Win 250 __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ ENGINE REMOVAL/INSTALLATION __________________________________________________________________________________ SERVICE INFORMATION -------------------------------------------- 5-1 ENGINE REMOVAL --------------------------------------------------- 5-2 ENGINE INSTALLATION -------------------------------------------- 5-4 www.PlanDeGraissage.org...
Page 56
5. ENGINE REMOVAL/INSTALLATION Bet & Win 250 SERVICE INFORMATION GENERAL INSTRUCTIONS • A floor jack or other adjustable support is required to support and maneuver the engine. Be careful not to damage the motorcycle body, cables and wires during engine removal. •...
Page 57
. ENGINE REMOVAL/INSTALLATION Bet & Win 250 Wire Connectors ENGINE REMOVAL Disconnect the battery negative cable. Remove the frame body cover. ( 2-3) Disconnect the engine negative cable. Disconnect all of the A.C. generator, auto bystarter, spark plug, thermosensor wire couplers and connectors.
Page 58
5. ENGINE REMOVAL/INSTALLATION Bet & Win 250 Rear Shock Absorber Upper Mount Bolts Remove the right/left rear shock absorber upper mount bolts. Remove the engine mounting bolt and pull out the engine. Engine Mounting Bolt Bolt ENGINE HANGER REMOVAL Remove the engine hanger bolts to remove the engine hanger.
Page 59
. ENGINE REMOVAL/INSTALLATION Bet & Win 250 ENGINE INSTALLATION Install the engine in the reverse order of removal. Tighten the engine mounting bolt. Torque: 49N-m Engine Mounting Bolt Rear Shock Absorber Upper Mount Bolts Tighten the rear shock absorber upper mount bolts.
Page 60
. CYLINDER HEAD/VALVES Bet & Win 250 __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ CYLINDER HEAD/VALVES __________________________________________________________________________________ SCHEMATIC DRAWING ---------------------------------------------- 6- 1 SERVICE INFORMATION -------------------------------------------- 6- 2 TROUBLESHOOTING ------------------------------------------------- 6- 3 CYLINDER HEAD COVER REMOVAL ----------------------------- 6- 4 CAMSHAFT REMOVAL----------------------------------------------- 6- 4 CYLINDER HEAD REMOVAL --------------------------------------- 6- 6 CYLINDER HEAD DISASSEMBLY --------------------------------- 6- 7 CYLINDER HEAD ASSEMBLY -------------------------------------- 6- 8...
. CYLINDER HEAD/VALVES Bet & Win 250 SERVICE INFORMATION GENERAL INSTRUCTIONS • The cylinder head can be serviced with the engine installed in the frame. Coolant in the radiator and water jacket must be drained first. • When assembling, apply molybdenum disulfide grease or engine oil to the valve guide movable parts and valve arm sliding surfaces for initial lubrication.
. CYLINDER HEAD/VALVES Bet & Win 250 TROUBLESHOOTING • The poor cylinder head operation can be diagnosed by a compression test or by tracing engine top-end noises. Poor performance at idle speed White smoke from exhaust muffler • Compression too low •...
. CYLINDER HEAD/VALVES Bet & Win 250 Cylinder Head Cover CYLINDER HEAD COVER REMOVAL Remove the center cover. ( 2-3) Remove the met-in box. ( 2-3) Remove the cylinder head cover four bolts and then remove the cylinder head cover. Bolt CAMSHAFT REMOVAL Turn the A.C.
Page 65
. CYLINDER HEAD/VALVES Bet & Win 250 Cam Chain Remove the camshaft gear from the cam chain to remove the camshaft. Camshaft Gear CAMSHAFT INSPECTION Check each cam lobe for wear or damage. Measure the cam lobe height. Service Limits: IN: 34.14mm replace if below EX:34.02mm replace if below Camshaft Bearings...
. CYLINDER HEAD/VALVES Bet & Win 250 Camshaft Holder CAMSHAFT HOLDER INSPECTION Inspect the camshaft holder, valve rocker arms and rocker arm shafts for wear or damage. * If the valve rocker arm contact surface is worn, check each cam lobe for wear or damage.
. CYLINDER HEAD/VALVES Bet & Win 250 Cylinder Head CYLINDER HEAD DISASSEMBLY Remove the valve spring cotters, retainers, springs, spring seats and valve stem seals using a valve spring compressor. * Be sure to compress the valve • springs with a valve spring compressor. Mark all disassembled parts to •...
. CYLINDER HEAD/VALVES Bet & Win 250 Straight Edge INSPECTION CYLINDER HEAD Check the spark plug hole and valve areas for cracks. Check the cylinder head for warpage with a straight edge and feeler gauge. Service Limit: 0.05mm repair or replace if over Feeler Gauge VALVE SPRING FREE LENGTH...
. CYLINDER HEAD/VALVES Bet & Win 250 Plastic Hammer Tap the valve stems gently with a plastic hammer to firmly seat the cotters. * Be careful not to damage the valves. Cylinder Head Gasket CYLINDER HEAD INSTALLATION Install the cam chain guide. Install the dowel pins and a new cylinder head gasket.
. CYLINDER HEAD/VALVES Bet & Win 250 Punch Marks CAMSHAFT INSTALLATION Turn the A.C. generator flywheel so that the “T” mark on the flywheel aligns with the index mark on the crankcase. Keep the round hole on the camshaft gear facing up and align the punch marks on the camshaft gear with the cylinder head surface (Position the intake and exhaust cam lobes...
. CYLINDER HEAD/VALVES Bet & Win 250 Tensioner Screw Turn the cam chain tension screw counter clockwise to release it. O-ring Apply engine oil to a new O-ring and install Tighten the cam chain tension cap screw. * Be sure to install the gasket into the groove properly.
. CYLINDER/PISTON Bet & Win 250 SERVICE INFORMATION GENERAL INSTRUCTIONS • The cylinder and piston can be serviced with the engine installed in the frame. • When installing the cylinder, use a new cylinder gasket and make sure that the dowel pins are correctly installed.
. CYLINDER/PISTON Bet & Win 250 Cylinder Cam Chain Guide CYLINDER REMOVAL Remove the cylinder head. ( 6-7) Remove the water hose from the cylinder. Water Hose Remove the cam chain guide. Remove the cylinder. Gasket Remove the cylinder gasket and dowel pins. Clean any gasket material from the cylinder surface.
Page 76
. CYLINDER/PISTON Bet & Win 250 Inspect the piston, piston pin and piston rings. Remove the piston rings. * • Take care not to damage or break the piston rings during removal. Clean carbon deposits from the piston ring grooves. Install the piston rings onto the piston and measure the piston ring-to-groove clearance.
Page 77
. CYLINDER/PISTON Bet & Win 250 Measure the piston pin O.D. Service Limit: 16.96mm replace if below Measure the piston O.D. * • Take measurement at 9mm from the bottom and 90° to the piston pin hole. Service Limit: 72.60mm replace if below Measure the piston-to-piston pin clearance.
Page 78
. CYLINDER/PISTON Bet & Win 250 Inspect the top of the cylinder for warpage. Service Limit: 0.05mm repair or replace if over Measure the connecting rod small end I.D. Service Limit: 17.06mm replace if over PISTON RING INSTALLATION Install the piston rings onto the piston. Apply engine oil to each piston ring.
. CYLINDER/PISTON Bet & Win 250 PISTON INSTALLATION Remove any gasket material from the crankcase surface. * • Be careful not to drop foreign matters into the crankcase. Piston Install the piston, piston pin and a new piston pin clip. *...
Page 80
. CYLINDER/PISTON Bet & Win 250 Install the cam chain guide. * • Insert the tab on the cam chain guide into the cylinder groove. Dowel Pin Install the cylinder gasket and dowel pins. Connect the water hose to the cylinder. Install the cylinder head.
Page 81
. DRIVE AND DRIVEN PULLEYS/ Bet & Win 250 KICK STARTER __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ DRIVE AND DRIVEN PULLEYS/ KICK STARTER __________________________________________________________________________________ SCHEMATIC DRAWING ---------------------------------------------- 8- 1 SERVICE INFORMATION -------------------------------------------- 8- 2 TROUBLESHOOTING ------------------------------------------------- 8- 2 LEFT CRANKCASE COVER------------------------------------------ 8- 3 DRIVE PULLEY -------------------------------------------------------- 8- 4 CLUTCH/DRIVEN PULLEY ------------------------------------------ 8- 8 www.PlanDeGraissage.org...
. DRIVE AND DRIVEN PULLEYS/ Bet & Win 250 KICK STARTER SERVICE INFORMATION GENERAL INSTRUCTIONS • The drive pulley, clutch and driven pulley can be serviced with the engine installed. • Avoid getting grease and oil on the drive belt and pulley faces. Remove any oil or grease from them to minimize the slipping of drive belt and drive pulley.
. DRIVE AND DRIVEN PULLEYS/ Bet & Win 250 KICK STARTER Air Tube Band LEFT CRANKCASE COVER REMOVAL Loosen the drive belt air tube band screw. Remove the four bolts on the left crankcase surface cover. Cover Bolts Remove the left crankcase cover bolts and left crankcase covers.
. DRIVE AND DRIVEN PULLEYS/ Bet & Win 250 KICK STARTER Install the drive belt air tube and tighten the tube band screw. Tube Band Screw Universal Holder DRIVE PULLEY REMOVAL Remove the left crankcase cover. Hold the drive pulley using an universal holder and remove the drive face nut and washer.
Page 86
. DRIVE AND DRIVEN PULLEYS/ Bet & Win 250 KICK STARTER Drive Pulley Collar Remove the movable drive face assembly. Remove the drive pulley collar. Movable Drive Face Assembly Ramp Plate DISASSEMBLY Remove the ramp plate. Remove the weight rollers. Weight Roller INSPECTION Check each weight roller for wear or damage.
Page 87
. DRIVE AND DRIVEN PULLEYS/ Bet & Win 250 KICK STARTER Measure the movable drive face bushing assembly I.D. Service Limit: 27.13mm replace if over Check the drive pulley collar for wear or damage. Measure the O.D. of the drive pulley collar sliding surface.
Page 88
. DRIVE AND DRIVEN PULLEYS/ Bet & Win 250 KICK STARTER Ramp Plate Install the ramp plate. Drive Pulley Collar Insert the drive pulley collar into the movable drive face. INSTALLATION Install the movable drive face onto the crankshaft. Movable Drive Face Assembly Driven Pulley Drive Pulley Collar Lay the drive belt on the driven pulley.
. DRIVE AND DRIVEN PULLEYS/ Bet & Win 250 KICK STARTER Drive Pulley Face Install the drive pulley face, washer and drive face nut. Drive Face Nut Washer Universal Holder Hold the drive pulley with the universal holder and tighten the drive face nut. Torque: 88.2_ 98N-m...
Page 90
. DRIVE AND DRIVEN PULLEYS/ Bet & Win 250 KICK STARTER Check the clutch shoes for wear or damage. Measure the clutch lining thickness. Service Limit: 2.0mm replace if below Clutch/Driven Pulley CLUTCH/DRIVEN PULLEY DISASSEMBLY Clutch Spring Compressor Hold the clutch/driven pulley assembly with the clutch spring compressor.
Page 91
. DRIVE AND DRIVEN PULLEYS/ Bet & Win 250 KICK STARTER Guide Roller Pin Guide Roller Pull out the guide roller pins and guide rollers. Remove the movable driven face from the driven face. Movable Driven Face O-ring Remove the oil seal from the movable driven Oil Seal face.
Page 92
. DRIVE AND DRIVEN PULLEYS/ Bet & Win 250 KICK STARTER Check the movable driven face for wear or damage. Measure the movable driven face I.D. Service Limit: 40.06mm replace if over DRIVEN PULLEY FACE BEARING REPLACEMENT Check the bearings for play and replace them if they have excessive play.
Page 93
. DRIVE AND DRIVEN PULLEYS/ Bet & Win 250 KICK STARTER Press a new needle bearing into the driven face. Special Bearing Driver Circlips CLUTCH DISASSEMBLY Remove the circlips and retainer plate to disassemble the clutch. * Keep grease off the clutch •...
Page 94
. DRIVE AND DRIVEN PULLEYS/ Bet & Win 250 KICK STARTER CLUTCH ASS EMBLY Circlips Install the damper rubbers on the drive plate pins. Install the clutch weights/shoes and clutch springs onto the drive plate. Install the retainer plate and secure with the circlips.
Page 95
. DRIVE AND DRIVEN PULLEYS/ Bet & Win 250 KICK STARTER Guide Roller Pin Guide Roller Install the movable driven face onto the driven face. Apply grease to the guide rollers and guide roller pins and then install them into the holes of the driven face.
Page 96
. DRIVE AND DRIVEN PULLEYS/ Bet & Win 250 KICK STARTER Clutch Outer Install the clutch outer. Hold the clutch outer with the universal holder. Install and tighten the clutch outer nut. Torque: 49.0_ 58.8kg-m Special Universal Holder Install the drive belt. ( 8-7) Install the left crankcase cover.
Page 97
. FINAL REDUCTION Bet & Win 250 __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ FINAL REDUCTION __________________________________________________________________________________ SCHEMATIC DRAWING ---------------------------------------------- 9-1 SERVICE INFORMATION -------------------------------------------- 9-2 TROUBLESHOOTING ------------------------------------------------- 9-2 FINAL REDUCTION DISASSEMBLY------------------------------- 9-3 FINAL REDUCTION INSPECTION---------------------------------- 9-3 FINAL REDUCTION ASSEMBLY ----------------------------------- 9-6 www.PlanDeGraissage.org...
Page 98
. FINAL REDUCTION Bet & Win 250 SCHEMATIC DRAWING www.PlanDeGraissage.org...
Page 99
. FINAL REDUCTION Bet & Win 250 SERVICE INFORMATION GENERAL INSTRUCTIONS • The servicing operations of this section can be made with the engine installed. • When replacing the drive shaft, use a special tool to hold the bearing inner race for this operation. SPECIFICATIONS Specified Oil: SAE 90# Oil Capacity:...
Page 100
. FINAL REDUCTION Bet & Win 250 Bolts FINAL REDUCTION DISASSEMBLY Remove the exhaust muffler. ( 2-6) Remove the rear brake caliper. ( 15-3) Remove the right rear shock absorber. ( 15-5) Remove the rear fork. ( 15-4) Remove the rear wheel. ( 15-4) Remove the left crankcase cover.
Page 101
. FINAL REDUCTION Bet & Win 250 Inspect the final gear and final shaft for wear, damage or seizure. Drive Shaft Bearing Check the left crankcase bearings for excessive play and inspect the oil seal for wear or damage. Final Shaft Bearing Countershaft Bearing Drive Shaft Bearing Inspect the drive shaft and gear for wear or...
Page 102
. FINAL REDUCTION Bet & Win 250 Bearing Remover, 15mm BEARING REPLACEMENT (TRANSMISSION CASE COVER) Remove the transmission case cover bearings using the bearing remover. Remove the final shaft oil seal. Drive Shaft Bearing Pilot, 15mm Drive new bearings into the transmission case cover.
Page 103
. FINAL REDUCTION Bet & Win 250 Drive new bearings into the left crankcase. Install a new drive shaft oil seal. Pilot FINAL REDUCTION ASSEMBLY Install the drive shaft into the left crankcase. Drive Shaft Install the final gear and final shaft into the left crankcase.
Page 104
. FINAL REDUCTION Bet & Win 250 Install the countershaft and gear into the left crankcase. Install the resin washer onto the counter- shaft. Install the dowel pins and a new gasket. Countershaft Install the transmission case cover. Transmission Case Cover Bolts Install and tighten the transmission case cover bolts.
Page 105
. FINAL REDUCTION Bet & Win 250 Oil Check Bolt Hole/Oil Filler After installation, fill the transmission case with the specified oil. * • Place the motorcycle on its main stand on level ground. • Check the oil-sealing washer for wear or damage.
Page 106
. A.C. GENERATOR/STARTER CLUTCH Bet & Win 250 __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ A.C. GENERATOR/STARTER CLUTCH __________________________________________________________________________________ SCHEMATIC DRAWING ---------------------------------------------- 10-1 SERVICE INFORMATION -------------------------------------------- 10-2 TROUBLESHOOTING ------------------------------------------------- 10-2 RIGHT CRANKCASE COVER REMOVAL-------------------------- 10-3 STATOR REMOVAL --------------------------------------------------- 10-3 FLYWHEEL REMOVAL----------------------------------------------- 10-3 STARTER CLUTCH ---------------------------------------------------- 10-4 FLYWHEEL INSTALLATION---------------------------------------- 10-5 STATOR INSTALLATION -------------------------------------------- 10-6...
. A.C. GENERATOR/STARTER CLUTCH Bet & Win 250 SERVICE INFORMATION GENERAL INSTRUCTIONS • All servicing operations and inspections in this section can be made with the engine installed. • Drain the coolant before removing the right crankcase cover. • Be careful not to drain the coolant when the engine temperature is high. (Perform this operation when the engine is cold.) •...
. A.C. GENERATOR/STARTER CLUTCH Bet & Win 250 Bolts Water Inlet Hose RIGHT CRANKCASE COVER REMOVAL Disconnect the water hoses from the right crankcase cover. Remove the nine bolts attaching the right crankcase cover and the cover. Water Outlet Hose A.C.
. A.C. GENERATOR/STARTER CLUTCH Bet & Win 250 Remove the starter one-way clutch rollers, plungers and springs. Starter Idle Gear Shaft INSTALLATION Install the starter driven gear onto the crankshaft. Install the starter idle gear and shaft. Starter Driven Gear Flywheel FLYWHEEL INSTALLATION Install the flywheel onto the crankshaft by...
. A.C. GENERATOR/STARTER CLUTCH Bet & Win 250 A.C. Generator Stator Screws STATOR INSTALLATION Install the A.C. generator stator on the right crankcase cover and secure it with the three bolts. Install the pulser coil on the right crankcase cover and secure it with the two screws. Install the wire grommet in the groove in the right crankcase cover securely.
. CRANKCASE/CRANKSHAFT Bet & Win 250 SERVICE INFORMATION GENERAL INSTRUCTIONS • This section covers crankcase separation to service the crankshaft. The engine must be removed for this operation. • When separating the crankcase, never use a driver to pry the crankcase mating surfaces apart forcedly to prevent damaging the mating surfaces.
. CRANKCASE/CRANKSHAFT Bet & Win 250 Cam Chain Tensioner Slipper CRANKCASE SEPARATION Remove the cam chain tensioner slipper bolt. Remove the cam chain tensioner slipper and cam chain. Remove the three right crankcase attaching bolts. Bolt Cam Chain Remove the left crankcase. Left Crankcase Right Crankcase Place the crankcase with the left crankcase...
. CRANKCASE/CRANKSHAFT Bet & Win 250 Oil Seal Remove the oil seal from the left crankcase. Left Crankcase CRANKSHAFT INSPECTION Measure the connecting rod big end side clearance. Service Limit: 0.6mm replace if over Measure the connecting rod small end I.D. Service Limit: 17.06mm replace if over 11-4 www.PlanDeGraissage.org...
. CRANKCASE/CRANKSHAFT Bet & Win 250 Measure the crankshaft runout. Service Limit: 0.10mm replace if over Measure the crankshaft bearing play. Play Service Limits: Play Axial : 0.20mm replace if over Radial : 0.05mm replace if over Axial Radial CRANKCASE ASSEMBLY Clean off all gasket material from the crankcase mating surfaces.
Page 119
. CRANKCASE/CRANKSHAFT Bet & Win 250 Place the left crankcase down and install the crankshaft into the left crankcase. * Avoid damaging the oil seal. • Apply grease to the lip of the oil • seal. Gasket Install the two dowel pins and a new gasket. Dowel Pins Right Crankcase Place the right crankcase over the crankshaft...
Page 120
. CRANKCASE/CRANKSHAFT Bet & Win 250 Cam Chain Tensioner Slipper Install the cam chain. Install the cam chain tensioner slipper. Install and tighten the cam chain tensioner slipper bolt. Torque: 7.8_ 11.8N-m Bolt 11-7 www.PlanDeGraissage.org...
Page 121
. COOLING SYSTEM Bet & Win 250 __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ COOLING SYSTEM __________________________________________________________________________________ SCHEMATIC DRAWING ---------------------------------------------- 12- 1 SERVICE INFORMATION -------------------------------------------- 12- 2 TROUBLESHOOTING ------------------------------------------------- 12- 2 COOLING SYSTEM TESTING --------------------------------------- 12- 4 RADIATOR -------------------------------------------------------------- 12- 4 WATER PUMP ---------------------------------------------------------- 12- 9 THERMOSENSOR ------------------------------------------------------ 12-15 THERMOSTAT---------------------------------------------------------- 12-16 12-0...
. COOLING SYSTEM Bet & Win 250 SERVICE INFORMATION GENERAL INSTRUCTIONS • The water pump must be serviced after removing the engine. Other cooling system service can be done with the engine installed in the frame. • The engine must be cool before servicing the cooling system. When the coolant temperature is over 100℃...
. COOLING SYSTEM Bet & Win 250 COOLING SYSTEM TESTING RADIATOR CAP INSPECTION Radiator Tester Install the radiator cap onto the radiator tester and apply specified pressure to it. It must hold specified pressure for at least six seconds. * Apply water to the cap sealing surface before testing.
Page 126
. COOLING SYSTEM Bet & Win 250 Inspect the radiator soldered joints and seams for leaks. Blow dirt out from between core fins with compressed air. If insects, etc., are clogging the radiator, wash them off. Carefully straighten any bent fins. Overflow Tube RADIATOR REMOVAL Drain the coolant.
Page 127
. COOLING SYSTEM Bet & Win 250 Fan Motor Wire Coupler Thermostatic Switch Disconnect the thermostatic switch wire coupler. Disconnect the fan motor wire coupler. Thermostatic Switch Wire Radiator Remove the two bolts and two nuts on the radiator. Nuts Bolts Fan/Shroud RADIATOR DISASSEMBLY...
Page 128
. COOLING SYSTEM Bet & Win 250 Battery Check fan motor by battery. Fan Motor Thermostatic Switch CHECK THERMOSTATIC SWITCH When coolant temperature lower then 85~90℃ the thermostatic switch OFF. When coolant temperature over 85~90℃ the thermostatic switch ON. Bolts Install the fan shroud on the radiator with the four bolts.
Page 129
. COOLING SYSTEM Bet & Win 250 Radiator RADIATOR INSTALLATION Install the radiator on the radiator bracket with the two bolts and two nuts. Bolts Nuts Upper Hose Connect the upper and lower hoses and secure them with hose bands. Connect the thermostatic switch wire and fan motor wire couplers.
. COOLING SYSTEM Bet & Win 250 Install the front upper cover. Right Crankcase Cover WATER PUMP MECHANICAL SEAL (WATER SEAL) INSPECTION Inspect the telltale hole for signs of mechanical seal coolant leakage. If the mechanical seal is leaking, remove the right crankcase cover and replace the mechanical seal.
Page 131
. COOLING SYSTEM Bet & Win 250 Bolts Water Pump Cover Remove the four bolts and the water pump cover, gasket and 2 dowel pins. Impeller (Left Hand Threads) Remove the water pump impeller. * The impeller has left hand threads. Mechanical Seal Inspect the mechanical (water) seal and seal washer for wear or damage.
Page 132
. COOLING SYSTEM Bet & Win 250 Bolts WATER PUMP SHAFT REMOVAL Disconnect the water hose from the right crankcase cover. Remove the eight bolts attaching the right crankcase cover. Water Pump Assembly Water Pump Assembly Inner Bearing Remove the water pump bearing snap ring from the water pump assembly.
Page 133
. COOLING SYSTEM Bet & Win 250 Water Pump Assembly MECHANICAL S EAL REPLACEMENT Drive the mechanical seal out of the water pump assembly from the inside. Mechanical Seal (Water Seal) Mechanical Seal Driver Drive in a new mechanical seal using a mechanical seal driver.
Page 134
. COOLING SYSTEM Bet & Win 250 Snap Ring Water Pump Shaft Install the water pump shaft and shaft inner bearing into the waster pump assembly. Install the snap ring to secure the inner bearing properly. Inner Bearing Bolts Install the dowel pins and a new gasket and then install the water pump assembly to the right crankcase cover.
Page 135
. COOLING SYSTEM Bet & Win 250 Impeller (Left Hand Threads) Install the impeller onto the water pump shaft. Torque: 9.8_ 13.7N-m * The impeller has left hand threads. Dowel Pins Install the two dowel pins and a new gasket. Water Pump Cover Install the water pump cover and tighten the 4 bolts.
. COOLING SYSTEM Bet & Win 250 THERMOSENSOR Thermosensor THERMOSENSOR REMOVAL Remove the seat, met-in box and center cover. Drain the coolant. Disconnect the thermosensor wire. Remove the thermosensor. Thermosensor Wire THERMOSENSOR INSPECTION Suspend the thermosensor in a pan of water over a burner and measure the resistance Thermosensor through the sensor as the water heats up.
. COOLING SYSTEM Bet & Win 250 Thermostat Bolt THERMOSTAT THERMOSTAT REMOVAL Remove the seat, met-in box and center cover. Drain the coolant. Disconnect the thermosensor wire from the thermosensor. Disconnect the water hose from the thermostat housing. Disconnect the air vent tube from the thermostat housing.
Page 138
. COOLING SYSTEM Bet & Win 250 THERMOSTAT INSPECTION Suspend the thermostat in a pan of water over a burner and gradually raise the water Thermostat temperature to check its operation. Technical Data Thermometer Begins to open 80±2℃ Full-open 90℃ Valve lift 3.5_ 4.5mm...
Page 139
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ FUEL SYSTEM/CARBURETOR/FUEL PUMP __________________________________________________________________________________ FUEL SYSTEM --------------------------------------------------------- 13- 1 SCHEMATIC DRAWING ---------------------------------------------- 13- 2 OPERATION OF CARBURETOR JETS------------------------------ 13- 3 SERVICE INFORMATION -------------------------------------------- 13- 5 CARBURETOR REMOVAL ------------------------------------------- 13- 7 VACUUM CHAMBER DISASSEMBLY------------------------------ 13- 7 FLOAT CHAMBER DISASSEMBLY--------------------------------- 13- 9...
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 OPERATION OF CARBURETOR JETS LOW SPEED Venturi (slightly opened throttle valve) ※ Air Bleed Holes‡ Mixture……. Low Speed Air Inlet Fuel in Float Chamber‡ Slow Jet ※ -------------------- Low Speed Small Jet Holes 2.MIDDLE SPEED Venturi (halfway opened throttle valve) Air Bleed Holes‡...
Page 143
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 FUEL PUMP CONSTRUCTION: The fuel pump adopted for this model is a vacuum-type fuel pump which utilizes the positive and negative pulsating pressures produced by the engine crankcase to control the oil pump diaphragms and deliver fuel from the fuel tank to the carburetor through the suction valve and outlet valve.
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 SERVICE INFORMATION GENERAL INSTRUCTIONS • When working with gasoline, keep away from sparks and flames. • Note the locations of O-rings when disassembling and replace them with new ones during assembly.
Page 145
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 TROUBLESHOOTING Engine does not start Engine idles roughly, stalls or runs poorly • No fuel in tank • Incorrect idle speed • Restricted fuel line • Rich mixture • Too much fuel getting to cylinder •...
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 Auto Bystarter Auto Bystarter Wire CARBURETOR REMOVAL Remove the seat, met-in box and center cover. Disconnect the fuel tube and vacuum tube at the carburetor. Disconnect the auto bystarter wire. Fuel Tube Throttle Cable Intake Manifold Band...
Page 147
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 Screws Remove the two vacuum chamber cover screws and the cover. Vacuum Chamber Cover Spring Remove the compression spring and vacuum piston. Vacuum Piston Diaphragm Vacuum Piston Remove the needle holder, spring and jet needle from the piston.
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 Float Chamber FLOAT CHAMBER DISASSEMBLY Remove the three float chamber screws and the float chamber. Screws Float Remove the float pin, float and float valve. Float Valve Float Pin Float Valve FLOAT VALVE INSPECTION Inspect the float valve seat contact area for...
Page 149
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 JETS/SCREWS REMOVAL * • Before removing the pilot screw, turn the pilot screw clockwise until it seats lightly and record the rotating turns. Do not force the pilot screw against its seat to avoid seat damage.
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 AUTO BYSTARTER INSPECTION /REMOVAL AUTO BYSTARTER INSPECTION Measure the resistance between the auto bystarter wire terminals. Resistance: 10W (10 minutes minimum after stopping the engine) If the reading is not within the limit, replace the auto bystarter with a new one.
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 AUTO BYSTARTER INSPECTION Check the auto bystarter valve and needle for nicks, wear or damage. If any faulty part is found, replace the auto bystarter with a new one. Bystarter Needle Bystarter Valve Air Cut-off Valve Cover...
Page 152
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 CARBURETOR BODY CLEANING Blow compressed air through all passages of the carburetor body. * • Make sure that no fuel jet is clogged. O-ring Install the O-ring onto the air-cut-off valve body securely.
Page 153
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 Screws ACCELERATING PUMP DISASSEMBLY Remove the two accelerating pump cover screws and accelerating pump cover. Remove the spring and accelerating pump diaphragm. Diaphragm Cover INSPECTION Inspect the accelerating pump diaphragm for cracks, damage or deterioration.
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 Main Jet Slow Jet FLOAT CHAMBER ASSEMBLY Install the main jet. Install the slow jet. Install the pilot screw. * • Be sure to record the rotating turns when it is removed. Pilot Screw Float Install the float valve, float and float pin.
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 FLOAT LEVEL INSPECTION Measure the float level at the location of the main jet (just contacting the float valve). Float Level: 18.5±1.0mm Replace the float if the level is incorrect. Check the operation of the float and then reinstall the float chamber.
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 Check the heater with battery. If the heater is getting hot, means the heater without problem, otherwise the heater has to be changed. Heater Air Cleaner Connecting Throttle Cable Tube Band CARBURETOR INSTALLATION Tighten the drain screw.
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 Vacuum Tube FUEL PUMP REMOVAL Remove the frame center cover. Disconnect the fuel pump inlet, outlet and vacuum tubes. Remove the two fuel pump attaching bolts and the fuel pump. Outlet Tube Fuel Strainer Inlet Tube...
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 Diaphragm FUEL PUMP INSPECTION Inspect the fuel pump diaphragms A and B for damage. Inspect each gasket for damage. Gaskets Relief Valve Outlet Suction Valve Inspect the suction valve, outlet valve and relief valve in the fuel pump body for damage, cracks or foreign matters.
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 Outlet Tube Fuel Pump Inlet Tube FUEL PUMP INSTALLATION Install the fuel pump and secure it with the two bolts. Connect the fuel pump inlet, outlet and vacuum tubes. Install the seat, met-in box and frame center cover.
Page 160
. FUEL SYSTEM/CARBURETOR/ FUEL PUMP/ FUEL TANK Bet & Win 250 FUEL STRAINER REMOVAL Remove the fuel strainer from the fuel tank. INSPECTION Inspect if the fuel strainer is clogged and clean it with compressed air. * • When removing the fuel strainer, do not allow flames or sparks near the working area and drain the residual gasoline into a container.
Page 161
14.STEERING HANDLEBAR/FRONT WHEEL/FRONT Bet & Win 250 BRAKE/FRONT SHOCK ABSORBER/FRONT FORK __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ STEERING HANDLEBAR/FRONT WHEEL/FRONT BRAKE/FRONT SHOCK ABSORBER/FRONT FORK __________________________________________________________________________________ SCHEMATIC DRAWING ---------------------------------------------- 14- 1 SERVICE INFORMATION -------------------------------------------- 14- 2 TROUBLESHOOTING ------------------------------------------------- 14- 3 STEERING HANDLEBAR--------------------------------------------- 14- 4 FRONT WHEEL--------------------------------------------------------- 14- 5 FRONT BRAKE --------------------------------------------------------- 14- 8 FRONT SHOCK ABSORBER------------------------------------------ 14-14...
14.STEERING HANDLEBAR/FRONT WHEEL/FRONT Bet & Win 250 BRAKE/FRONT SHOCK ABSORBER/FRONT FORK SERVICE INFORMATION GENERAL INSTRUCTIONS • Remove the motorcycle frame covers before removing the front wheel, steering handlebar, front shock absorber and front fork. Jack the motorcycle front wheel off the ground and be careful to prevent the motorcycle from falling down.
14.STEERING HANDLEBAR/FRONT WHEEL/FRONT Bet & Win 250 BRAKE/FRONT SHOCK ABSORBER/FRONT FORK Brake Master Cylinders STEERING HANDLEBAR REMOVAL Remove the handlebar front and rear covers. ( 2-6) Remove the front and rear brake master cylinder attaching bolts. Remove the front upper cover. ( 2-5) Remove the front lower cover.
14.STEERING HANDLEBAR/FRONT WHEEL/FRONT Bet & Win 250 BRAKE/FRONT SHOCK ABSORBER/FRONT FORK Throttle Grip Throttle Cable Lubricate the throttle grip front end with grease and then install the throttle grip. Connect the throttle cable to the throttle grip. Install the right and left handlebar switches and tighten the screws.
Page 167
14.STEERING HANDLEBAR/FRONT WHEEL/FRONT Bet & Win 250 BRAKE/FRONT SHOCK ABSORBER/FRONT FORK WHEEL RIM Check the wheel rim runout. Service Limits: Radial: 2.0mm replace if over Axial: 2.0mm replace if over FRONT WHEEL BEARING Remove the side collar and dust seal. Turn the inner race of each bearing with your finger to see if they turn smoothly and quietly.
Page 168
14.STEERING HANDLEBAR/FRONT WHEEL/FRONT Bet & Win 250 BRAKE/FRONT SHOCK ABSORBER/FRONT FORK Driver Handle Pack all bearing cavities with grease. Drive in the left bearing. Install the distance collar. Drive in the right bearing. * Do not allow the bearings to tilt •...
14.STEERING HANDLEBAR/FRONT WHEEL/FRONT Bet & Win 250 BRAKE/FRONT SHOCK ABSORBER/FRONT FORK Holder Bolts FRONT BRAKE BRAKE MASTER CYLINDER REM OVAL Remove the handlebar covers. ( 2-6) First drain the brake fluid from the hydraulic brake system. Disconnect the front stop switch wire connector.
Page 170
14.STEERING HANDLEBAR/FRONT WHEEL/FRONT Bet & Win 250 BRAKE/FRONT SHOCK ABSORBER/FRONT FORK INSPECTION Measure the brake master cylinder I.D. Inspect the master cylinder for scratches or cracks. Service Limit: 12.75mm Measure the brake master cylinder piston O.D. Service Limit: 12.64mm Before assembly, inspect the lst and 2nd rubber cups for wear.
Page 171
14.STEERING HANDLEBAR/FRONT WHEEL/FRONT Bet & Win 250 BRAKE/FRONT SHOCK ABSORBER/FRONT FORK Connect the front stop switch wire connector. Install the handlebar covers. ( 2-6) Stop Switch Wire Connector BRAKE FLUID REFILLING Keep the handlebar upright and remove the brake reservoir cover and diaphragm. Add DOT-3 brake fluid to the brake reservoir.
Page 172
14.STEERING HANDLEBAR/FRONT WHEEL/FRONT Bet & Win 250 BRAKE/FRONT SHOCK ABSORBER/FRONT FORK Bleed Valve BRAKE CALIPER REMOVAL First drain the brake fluid from the hydraulic brake system. Remove the brake fluid tube bolt. Remove the two bolts attaching the brake caliper. Remove the brake caliper.
Page 173
14.STEERING HANDLEBAR/FRONT WHEEL/FRONT Bet & Win 250 BRAKE/FRONT SHOCK ABSORBER/FRONT FORK Check the piston for scratches or wear. Measure the piston O.D. with a micrometer gauge. Service Limit: 25.30mm Check the caliper cylinder for scratches or wear and measure the cylinder bore. Service Limit: 25.45mm ASSEMBLY Clean all removed parts.
Page 174
14.STEERING HANDLEBAR/FRONT WHEEL/FRONT Bet & Win 250 BRAKE/FRONT SHOCK ABSORBER/FRONT FORK Brake Fluid Tube Connect the brake fluid tube to the brake caliper and tighten the fluid tube bolt. Torque: 24.5_ 34.3N-m Fill the brake reservoir with the specified brake fluid and bleed air from the brake system.
14.STEERING HANDLEBAR/FRONT WHEEL/FRONT Bet & Win 250 BRAKE/FRONT SHOCK ABSORBER/FRONT FORK Front Fork FRONT SHOCK ABSORBER REMOVAL Remove the front upper cover. ( 2-5) Remove the front lower cover. ( 2-5) Remove the front wheel. ( 14-5) Remove the front brake caliper. ( 14-11) Remove the front shock absorber upper mount bolts.
Page 176
14.STEERING HANDLEBAR/FRONT WHEEL/FRONT Bet & Win 250 BRAKE/FRONT SHOCK ABSORBER/FRONT FORK Shock Absorber Tube INSPECTION Inspect the following items and replace if necessary. •Front shock absorber tube bending, damage or wear •Weak front shock absorber spring •Damper and damper rod bending •Oil seal damage or wear Measure the front shock absorber spring free length.
Page 177
14.STEERING HANDLEBAR/FRONT WHEEL/FRONT Bet & Win 250 BRAKE/FRONT SHOCK ABSORBER/FRONT FORK ASSEMBLY Install the damper spring onto the damper rod and then install them into the front shock absorber tube. Install the shock absorber spring onto the front shock absorber tube. Set the front shock absorber tube in a vise and then tighten the lock nut.
Page 178
14.STEERING HANDLEBAR/FRONT WHEEL/FRONT Bet & Win 250 BRAKE/FRONT SHOCK ABSORBER/FRONT FORK Lock Nut Socket FRONT FORK REMOVAL Remove the handlebar covers. ( 2-6) Remove the steering handlebar. ( 14-4) Remove the front upper cover. ( 2-5) Remove the front lower cover. ( 2-5) Remove the front inner fender.
Page 179
14.STEERING HANDLEBAR/FRONT WHEEL/FRONT Bet & Win 250 BRAKE/FRONT SHOCK ABSORBER/FRONT FORK Outer Driver Drive in new ball races. * Be sure to drive the ball races into place completely. Bottom Ball Race INSTALLATION Apply grease to the top and bottom ball races and install 26 steel balls on the top ball race and 19 steel balls on the bottom ball race.
. REAR BRAKE/REAR FORK/REAR Bet & Win 250 WHEEL/REAR SHOCK ABSORBER SERVICE INFORMATION GENERAL INSTRUCTIONS • When performing the services stated in this section, the engine and exhaust muffler must be cold to avoid scalding. • During servicing, keep oil or grease off the brake pads and brake disk. SPECIFICATIONS Item Standard (mm)
. REAR BRAKE/REAR FORK/REAR Bet & Win 250 WHEEL/REAR SHOCK ABSORBER REAR FORK Shock Absorber Lower Mount Bolt REMOVAL Remove the exhaust muffler. ( 2-6) Remove the rear brake caliper. ( 15-3) Remove the right rear shock absorber lower mount bolt. Remove the rear axle nut and remove the collar.
. REAR BRAKE/REAR FORK/REAR Bet & Win 250 WHEEL/REAR SHOCK ABSORBER Shock Absorber Lower Mount Bolt INSTALLATION The installation sequence is the reverse of removal. Torque: Rear shock absorber lower mount bolt: 19.6_ 29.4N-m Rear axle nut: 78.4_ 98N-m Brake Caliper Bolts Axle Nut ADJUSTABLE REAR CUSHION To suit scooter behaviour to load condition...
Page 186
. REAR BRAKE/REAR FORK/REAR Bet & Win 250 WHEEL/REAR SHOCK ABSORBER Spring Rubber INSPECTION Inspect the damper rod for bending or damage. Inspect the damper for oil leaks. Inspect the damper rubber for deterioration or damage. Damper Damper Rod Measure the front shock absorber spring free length.
Page 187
. BATTERY/CHARGING SYSTEM Bet & Win 250 __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ BATTERY/CHARGING SYSTEM __________________________________________________________________________________ CHARGING SYSTEM LAYOUT-------------------------------------- 16-1 SERVICE INFORMATION -------------------------------------------- 16-2 TROUBLESHOOTING ------------------------------------------------- 16-3 BATTERY---------------------------------------------------------------- 16-4 CHARGING SYSTEM -------------------------------------------------- 16-5 A.C. GENERATOR INSPECTION ------------------------------------ 16-5 REGULATOR/RECTIFIER INSPECTION --------------------------- 16-6 16-0 www.PlanDeGraissage.org...
. BATTERY/CHARGING SYSTEM Bet & Win 250 CHARGING SYSTEM LAYOUT Fuse Battery A.C. Generator Regulator/Rectifier CHARGING CIRCUIT 16-1 www.PlanDeGraissage.org...
. BATTERY/CHARGING SYSTEM Bet & Win 250 SERVICE INFORMATION GENERAL INSTRUCTIONS * The battery electrolyte (sulfuric acid) is poisonous and may seriously damage the skin and eyes. Avoid contact with skin, eyes, or clothing. In case of contact, flush with water and get prompt medical attention •...
. BATTERY/CHARGING SYSTEM Bet & Win 250 SPECIAL TOOLS Universal holder Flywheel puller TROUBLESHOOTING No power Intermittent power • Dead battery • Loose battery cable connection • Disconnected battery cable • Loose charging system connection • Fuse burned out • Loose connection or short circuit in ignition system •...
. BATTERY/CHARGING SYSTEM Bet & Win 250 Battery Cover Screw BATTERY Remove the seat and met-in box. ( 2-3) Remove the battery cover screw and the battery cover. Remove the battery. First disconnect the battery negative (-) cable and then the positive (+) cable. *...
. BATTERY/CHARGING SYSTEM Bet & Win 250 CHARGING SYSTEM Red Wire CURRENT TEST * Use a fully charged battery (12.8V min.) to check the charging system. Warm up the engine before taking readings. Connect an electric tester across the battery terminals.
. BATTERY/CHARGING SYSTEM Bet & Win 250 A.C. Generator Stator Pulser Coil A.C. GENERATOR REMOVAL A.C. generator removal ( 10-3) A.C. generator installation ( 10-6) Right Crankcase Cover Bolts REGULATOR/RECTIFIER INSPECTION Remove the frame front cover. ( 2-5) Remove the regulator/rectifier wire coupler. Check the continuity between the wire terminals.
Page 194
. IGNITION SYSTEM Bet & Win 250 __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ IGNITION SYSTEM __________________________________________________________________________________ IGNITION SYSTEM LAYOUT --------------------------------------- 17-1 SERVICE INFORMATION -------------------------------------------- 17-2 TROUBLESHOOTING ------------------------------------------------- 17-2 SPARK PLUG ----------------------------------------------------------- 17-3 IGNITION COIL INSPECTION --------------------------------------- 17-3 A.C. GENERATOR INSPECTION ------------------------------------ 17-4 CDI UNIT RESISTANCE INSPECTION----------------------------- 17-5 17-0 www.PlanDeGraissage.org...
. IGNITION SYSTEM Bet & Win 250 IGNITION SYSTEM LAYOUT CDI Unit Ignition Coil Ignition Switch Pulser Coil A.C. Generator IGNITION CIRCUIT 17-1 www.PlanDeGraissage.org...
. IGNITION SYSTEM Bet & Win 250 SERVICE INFORMATION GENERAL INSTRUCTIONS • Check the ignition system according to the sequence specified in the Troubleshooting. ( 1-28) • The ignition system adopts CDI unit and the ignition timing cannot be adjusted. •...
. IGNITION SYSTEM Bet & Win 250 Ignition Coil SPARK PLUG For spark plug inspection and adjustment, refer to page 3-5. IGNITION COIL INSPECTION Remove the seat and met-in box. ( 2-3) Remove the ignition coil Ignition Coil Primary Coil IGNITION COIL CONTINUITY TEST Inspect the continuity of the ignition coil, primary coil and secondary coil.
. IGNITION SYSTEM Bet & Win 250 A .C. GENERATOR INSPECTION EXCITER COIL/PULSER COIL INSPECTION * This test is performed with the stator installed in the engine. Remove the frame right cover. ( 2-4) Disconnect the A.C. generator connector. Measure the exciter coil resistance between the black/red wire terminal and ground.
Page 199
. IGNITION SYSTEM Bet & Win 250 CDI UNIT RESISTANCE INSPECTION Measure the resistance between the terminals. Replace the CDI unit if the readings are not within the specifications in the table below. * • Due to the semiconductor in circuit, it is necessary to use a specified tester for accurate testing.
Page 200
. STARTING SYSTEM Bet & Win 250 __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ STARTING SYSTEM __________________________________________________________________________________ STARTING SYSTEM LAYOUT -------------------------------------- 18-1 SERVICE INFORMATION -------------------------------------------- 18-2 TROUBLESHOOTING ------------------------------------------------- 18-2 STARTER MOTOR ----------------------------------------------------- 18-3 STARTER CLUTCH INSPECTION----------------------------------- 18-5 STARTER RELAY INSPECTION ------------------------------------ 18-6 18-0 www.PlanDeGraissage.org...
. STARTING SYSTEM Bet & Win 250 SERVICE INFORMATION GENERAL INSTRUCTIONS • The removal of starter motor can be accomplished with the engine installed. • For the starter clutch removal, refer to page 10-3. • After the starter clutch is installed, be sure to add the engine oil and coolant and then bleed air from the cooling system.
. STARTING SYSTEM Bet & Win 250 STARTER MOTOR REMOVAL * • Before removing the starter motor, turn the ignition switch OFF and remove the battery ground. Then, turn on the ignition switch and push the starter button to see if the starter motor operates properly.
Page 204
. STARTING SYSTEM Bet & Win 250 STARTER MOTOR CASE CONTINUITY CHECK Check to confirm that there is no continuity between the starter motor wire terminal and the motor front cover. Also check for the continuity between the wire terminal and each brush. Replace if necessary.
. STARTING SYSTEM Bet & Win 250 ASSEMBLY Apply grease to the dust seal in the front cover. Install the brushes onto the brush holders. Apply a thin coat of grease to the two ends of the armature shaft. Insert the commutator into the front cover. Motor Case Mark Install a new O-ring to the front cover.
. STARTING SYSTEM Bet & Win 250 STARTER RELAY INSPECTION Disconnect the starter relay wire connector. Check for continuity between the yellow/red wire terminal and ground. There should be continuity when the starter button is depressed. If there is no continuity, check the starter button for continuity and inspect the wire.
. SWITCHES/HORN/FUEL UNIT/THERMOSTATIC SWITCH Bet & Win /TEMPERATURE GAUGE/INSTRUMENTS/LIGHTS 125/150 SERVICE INFORMATION GENERAL INSTRUCTIONS • After installation of each switch, a continuity check must be performed. A continuity check can usually be made without removing the part from the motorcycle. TESTING INSTRUMENT Electric tester SPECIAL TOOL...
. SWITCHES/HORN/FUEL UNIT/THERMOSTATIC SWITCH Bet & Win /TEMPERATURE GAUGE/INSTRUMENTS/LIGHTS 125/150 SWITCHES IGNITION SWITCH INSPECTION Remove the frame front covers. ( 2-5) Disconnect the ignition switch wire couplers. Check for continuity between the wire terminals. Color Black/Wh Green Black Position PARK LOCK ○...
Page 211
. SWITCHES/HORN/FUEL UNIT/THERMOSTATIC SWITCH Bet & Win /TEMPERATURE GAUGE/INSTRUMENTS/LIGHTS 125/150 HORN BUTTON INSPECTION Remove the frame front covers. ( 2-5) Disconnect the horn wire couplers. Depress the horn button and check for continuity between the wire terminals. Color Light Green Brown/Blue Position FREE...
. SWITCHES/HORN/FUEL UNIT/THERMOSTATIC SWITCH Bet & Win /TEMPERATURE GAUGE/INSTRUMENTS/LIGHTS 125/150 HORN INSPECTION Remove the front upper cover. ( 2-5) Disconnect the horn wire couplers. The horn is normal if it sounds when a 12V battery is connected across the horn wire terminals.
. SWITCHES/HORN/FUEL UNIT/THERMOSTATIC SWITCH Bet & Win /TEMPERATURE GAUGE/INSTRUMENTS/LIGHTS 125/150 Thermostatic Switch THERMOSTATIC SWITCH INSPECTION Remove the front covers. ( 2-5) Start and run the engine to make the water temperature reaches 85℃_ 90℃ and check if the cooling fan motor operates. Lower the water temperature to 85℃...
. SWITCHES/HORN/FUEL UNIT/THERMOSTATIC SWITCH Bet & Win /TEMPERATURE GAUGE/INSTRUMENTS/LIGHTS 125/150 Speedometer Cable INSTRUMENTS REMOVAL Remove the front upper cover. ( 2-5) Disconnect the instrument wire couplers and connectors. Disconnect the speedometer cable. Wire Couplers Remove the four instrument cover and leg shield screws.
. SWITCHES/HORN/FUEL UNIT/THERMOSTATIC SWITCH Bet & Win /TEMPERATURE GAUGE/INSTRUMENTS/LIGHTS 125/150 Wire LIGHTS HEADLIGHT BULB REPLACEMENT Remove the front upper cover. ( 2-5) Disconnect the headlight and turn signal light wire couplers. Remove the rubber boot from the bulb socket. Remove the bulb socket and replace the bulb. Install the bulb socket, aligning the bulb socket tab with the groove.
Need help?
Do you have a question about the Bet & Win 250 and is the answer not in the manual?
Questions and answers
Hi, how do I set the main light. It shines too high.
To adjust the main light (headlight) on a KYMCO Bet & Win 250, turn the headlight aim adjusting bolt.
This answer is automatically generated