Table of Contents
Advertisement
Beating dust on the filter
CAUTION:
Do not turn the dial on the dust
case while the dust case is removed from the
dust collection system. Doing so may cause dust
inhalation.
CAUTION:
Always switch off the tool when
turning the dial on the dust case. Turning the dial
while the tool is running may result in the loss of
control of the tool.
By beating the dust on the filter inside the dust case,
you can keep the vacuum efficiency and also reduce
the number of times to dispose of the dust.
Turn the dial on the dust case three times after col-
lecting every 50,000 mm
vacuum performance declined.
3
NOTE: 50,000 mm
of dust equivalents to drilling 10
holes of ø10 mm and 65 mm depth.
► Fig.39: 1. Dust case 2. Dial
Disposing of dust
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION:
Be sure to wear dust mask when
disposing of dust.
CAUTION:
Empty the dust case regularly
before the dust case becomes full. Failure to do so
may decrease the dust collection performance and
cause dust inhalation.
CAUTION:
The performance of dust collection
decreases if the filter in the dust case become
clogged. Replace the filter with new one after
approximately 200 times of dust fulfillment as a
guide. Failure to do so may cause dust inhalation.
1.
Remove the dust case while pressing down the
latch lever of the dust case.
► Fig.40: 1. Latch lever
2.
Lift the lock tab slightly outwards and open the
dust case cover.
► Fig.41: 1. Dust case cover 2. Lock tab
3.
Dispose of the dust, and then clean the filter.
► Fig.42
NOTICE:
When cleaning the filter, tap the case
of the filter gently by hand to remove dust. Do not
tap the filter directly; touch the filter with brush
or similar; or blow compressed air on the filter.
Doing so may damage the filter.
3
of dust or when you feel the
Replacing filter of dust case
1.
Remove the dust case while pressing down the
latch lever of the dust case.
► Fig.43: 1. Latch Lever
2.
Lift the lock tab slightly outwards and open the
filter cover of the dust case.
► Fig.44: 1. Filter cover 2. Lock tab
3.
Remove the filter from the filter case.
► Fig.45: 1. Filter 2. Filter case
4.
Attach a new filter to the filter case, and then
attach the filter cover.
5.
Close the cover of the dust case, and then attach
the dust case to the dust collection system.
Replacing sealing cap
A damaged or worn-out sealing cap may affect the dust
collecting performance. Replace the sealing cap with
new one as appropriate, aligning its guide projection
with guide notch on the nozzle head.
► Fig.46: 1. Sealing cap 2. Guide projection 3. Nozzle
head 4. Guide notch
Storage
NOTICE:
When not in use for a certain period of
time, the nozzle guide needs to be extended to
approximately 100 mm from its fully shortened
position. Failing to do so may damage the duct hose
pre-installed in the nozzle guide.
► Fig.47: 1. Guide adjustment button 2. Approx.
100 mm
OPERATION
CAUTION:
Always use the side grip (auxiliary
handle) and firmly hold the tool by both side grip
and switch handle during operations.
CAUTION:
Always make sure that the work-
piece is secured before operation.
CAUTION:
Do not pull the tool out forcibly
even the bit gets stuck. Loss of control may
cause injury.
NOTICE:
Before using the dust collection sys-
tem with the tool, read the section about the dust
collection system.
NOTE: If the battery cartridge is in low temperature,
the tool's capability may not be fully obtained. In this
case, warm up the battery cartridge by using the
tool with no load for a while to fully obtain the tool's
capability.
► Fig.48
22 ENGLISH
Advertisement
Table of Contents
