Net weight 5.2 - 6.8 kg 5.3 - 6.7 kg Optional accessory Model: DX10 (For HR008G) DX11 (For HR009G) Applicable workpiece and workmode for concrete drilling only (not for metal or wood, and not for core drilling or chiseling) Suction performance...
) : 103 dB (A) h, HD operation* Uncertainty (K) : 3 dB(A) Chiselling 8.6 m/s 1.5 m/s EN62841-2-6 Model HR008G with DX10 h, CHeq 8.0 m/s 1.5 m/s Recommended Sound pressure level (L ) : 94 dB(A) practical Sound power level (L...
In cold weather or when the tool has not been EC Declaration of Conformity used for a long time, let the tool warm up for a while by operating it under no load. This For European countries only will loosen up the lubrication. Without proper The EC declaration of conformity is included as Annex A warm-up, hammering operation is difficult.
Page 15
Avoid storing battery cartridge in a con- causing fires, personal injury and damage. It will tainer with other metal objects such as also void the Makita warranty for the Makita tool and nails, coins, etc. charger. Do not expose battery cartridge to water or rain.
If not, supplied case or a static-free container. it may accidentally fall out of the tool, causing injury to 26. Do not insert any devices other than Makita you or someone around you. wireless unit into the slot on the tool. CAUTION: Do not install the battery cartridge 27.
If no improvement can be found by restoring protection CAUTION: If the lamp goes off after blinking system, then contact your local Makita Service Center. for a few seconds, the active feedback sensing technology is not working properly. Ask your Switch action local Makita Service Center for repair.
Page 18
Reversing switch action Selecting the action mode ► Fig.6: 1. Reversing switch lever NOTICE: Do not rotate the action mode changing knob when the tool is running. The tool will be damaged. CAUTION: Always check the direction of NOTICE: To avoid rapid wear on the mode rotation before operation.
16. In the event the tool is dropped, it must be if the screws are not tightened. tagged and removed from service, and should be inspected by a Makita Factory or Authorized CAUTION: Always use a locking carabiner Service Center.
Installation before installing the drill bit. Coat the shank end of the drill bit beforehand with a For model HR008G small amount of grease (about 0.5 - 1 g). This chuck lubrication assures smooth action and lon- Attach the spacer to the attachment unit of the ger service life.
Uninstallation Installation Push the chuck cover down all the way and pull a NOTICE: Before installing the dust collection bit off. system, clean the joint parts of the tool and the ► Fig.29: 1. Bit 2. Chuck cover dust collection system. Foreign matters on the joint Hold the attachment unit of the dust cup set and parts may cause it difficult to install the dust collection pull it apart from the tool.
Storage NOTE: 50,000 mm of dust equivalents to drilling 10 holes of ø10 mm and 65 mm depth. NOTICE: When not in use for a certain period of ► Fig.39: 1. Dust case 2. Dial time, the nozzle guide needs to be extended to Disposing of dust approximately 100 mm from its fully shortened position.
Page 23
WIRELESS ACTIVATION Set the action mode changing knob to the symbol. FUNCTION For model HR008G What you can do with the wireless Optional accessory activation function Attach the chuck adapter to a keyless drill chuck to which 1/2"-20 size screw can be installed, and then...
Page 24
► Fig.62: 1. Wireless activation button 2. Wireless cleaner activation lamp Turn on the tool. Check if the vacuum cleaner runs NOTE: A Makita vacuum cleaner supporting the while the tool is operating. wireless activation function is required for the tool registration.
Page 25
Description of the wireless activation lamp status ► Fig.63: 1. Wireless activation lamp The wireless activation lamp shows the status of the wireless activation function. Refer to the table below for the meaning of the lamp status. Status Wireless activation lamp Description Color Duration...
Page 26
Troubleshooting for wireless activation function Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace- ment parts for repairs. State of abnormality Probable cause (malfunction) Remedy The wireless activation lamp does The wireless unit is not installed into the tool.
Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual.