Spectra Logic Spectra 10000 Install Manual
Power supply
Hide thumbs
Also See for Spectra 10000:
- User manual (138 pages) ,
- Installation manual (27 pages) ,
- Install manual (21 pages)
Related Manuals for Spectra Logic Spectra 10000
Summary of Contents for Spectra Logic Spectra 10000
- Page 1 Spectra 4000-10000 Library ™ Power Supply Replacement Guide P.N. 90840072 Revision E...
-
Page 2: Contact Information
Information furnished in this manual is believed to be accurate and reliable. However, no responsibility is assumed by Spectra Logic for its use. Due to continuing research and development, Spectra Logic may revise this publication from time to time without notice, and reserves the right to change any product specification at any time without notice. - Page 3 Spectra 4000-10000™ Library Power Supply Replacement Guide Contents Introduction ... 4 Prepare the Library... 5 Remove the Power Supply... 6 Replace the Power Supply... 12...
-
Page 4: Introduction
Materials and Tools Required You will need a Power Supply Assembly Kit to install a new Power Supply into your library. These kits are available from Spectra Logic, or an authorized Spectra Logic reseller. • Spectra 4000-9000 Power Supply Kit: P.N. 90841634 •... -
Page 5: Prepare The Library
Spectra 4000-10000™ Library Power Supply Replacement Guide Prepare the Library 1. Quit all programs and shut down your computer. 2. Turn off power to your computer. 3. Turn off power to your library. Switch off power to any other connected equipment. -
Page 6: Remove The Power Supply
Spectra 4000-10000™ Library Power Supply Replacement Guide Remove the Power Supply 1. Use the appropriate screwdriver to completely remove the three library cover screws on the rear of the library (Figure 1). Figure 1 Remove the screws. 2. Slide the cover toward the rear of the library about one-half inch. This releases the side clips holding the cover to the front panel (Figure 2). - Page 7 5. Use the appropriate screwdriver to remove the screws holding the rear panel of the library in place (Figure 4 and Figure 5). Figure 4 Screws holding the rear panel in place. Note: If the library is rack mounted, the lower screws on each side are not installed.
- Page 8 Spectra 4000-10000™ Library Power Supply Replacement Guide 8. Disconnect the DC power plugs from the rear of each drive (Figure 8). Figure 8 Rear panel lowered and drives unplugged. 9. Detach the yellow SCSI ribbon cable from Drive 1. 10. Detach Drive 1’s nine-pin, rainbow-colored ID cable from the rear panel (Figure 9).
- Page 9 Spectra 4000-10000™ Library Power Supply Replacement Guide 12. Disconnect the AC power switch cable at the connector located next to the rotary motor (Figure 11). Figure 11 Detach the power switch cable. Note: Check to see if the 13-pin power supply DC cable connection (red, black and yellow wires) is located outside of the cage.
- Page 10 Spectra 4000-10000™ Library Power Supply Replacement Guide 14. Tilt the power supply toward the drives and remove the two screws on the back of the power supply that hold the cage in place (Figure 13). 15. Turn the power supply upside down and remove the two screws on the bottom of the power supply that hold the power supply cage in place (Figure 14).
- Page 11 Spectra 4000-10000™ Library Power Supply Replacement Guide 18. Remove the power supply (Figure 17 and Figure 18). Figure 17 The library with the power supply Figure 18 The power supply by itself. removed.
-
Page 12: Replace The Power Supply
1. Remove the protective packaging from the new power supply. Note: If you are installing a Spectra 10000 Power Supply Kit, P.N. 92848069, you do not need to remove the cage. The 13-pin power supply DC cable (red, black and yellow wires) is located outside of the cage. - Page 13 Spectra 4000-10000™ Library Power Supply Replacement Guide 5. Plug in the 13-pin power supply DC cable with red, black and yellow wires (Figure 21). Figure 21 Plug in the SCSI unit’s 13-pin DC cable. 6. Replace the four screws that hold the power supply cage in place. Go to Step 8 once you have replaced the screws.
- Page 14 Caution: When reinstalling the power supply, ensure that there are no pinched cables or wires prior to tightening the captive screws. Figure 23 Tighten the two captive screws. 10. Attach the AC power switch cable at the connector located by the rotary motor (Figure 24).
- Page 15 Spectra 4000-10000™ Library Power Supply Replacement Guide 12. Attach the drive’s nine-pin, rainbow-colored ID cable to the rear panel (Figure 25). Figure 25 Attach the ID cable to the rear panel. 13. Attach the yellow SCSI ribbon cable to Drive 1. 14.
- Page 16 Spectra 4000-10000™ Library Power Supply Replacement Guide Caution: For Fibre Channel units only, make sure that the brass EMI clip on the rear panel is properly aligned around the Fibre Channel port (Figure 28). Brass EMI Clip Figure 28 Location of the brass EMI clip on a Fibre Channel library. 18.
- Page 17 19. Place the top cover on the library. Leave about one inch of space between the front of the cover and the front panel (Figure 30). 20. Using both hands, lightly squeeze the front sides of the cover together and slide the cover forward (Figure 31).
- Page 18 If you have difficulty If you have difficulty with any part of this procedure, contact Spectra Logic Technical Support at (800) 227-4637, or (303) 449-6444, extension 3175. Make sure to give the support representative the model and serial number of your library, and say that you...