Table of Contents
Advertisement
The keypad will display the following:
Part Entry Time A1
060 Seconds
Press 0-9 OK to SAVE
3. Use the numeric keys to enter the required time in
seconds and then press [OK]. Part entry time can be
set from 0 to 255 seconds.
Inputs
Each panel can have up to a maximum 144 zones. When
the optional radio receiver is fitted any available zone
may be programmed as a wireless zone. Your installer will
advise you on the exact makeup and configuration of your
system.
Inputs > Commands >
Zone Status
This menu allows you to view the zone status of each zone
(i.e. Normal, Open or Short).
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [3] + [0] + [0].
A list of different zones will display on the keypad.
2. Use the [] and [] keys to select the zone that you
want to turn view the status information then press
[OK] to select. Alternatively, you can enter the zone
number that you want to view status information,
then press [OK].
The keypad will display the following zone status
information:
Zone 1 Name Zn1
EOL=Normal 06523 ohms
Press OK or MENU
3. Press the [OK] key to exit.
Inputs > Commands >
Zone Array
This menu allows you to view zones in groups of sixteen.
The top two rows of the display show the zone number, the
third row displays the zone status
N= NORMAL
S = SHORTED
A= ALARM
T= TAMPER
- = DISABLED
If a 100 is displayed at the right hand side of the top line, it
means that you are displaying zones 97 to 112 or zones 113
to 128 etc. See example.
Enter programming mode (PIN + MENU) then,
Bosch Security Systems 3/23 BLCC610U
1. Enter [MENU] + [3] + [0] + [1] and use the up and
down arrows to select the zone group to view.
2. Use the up and down arrows at any time to move to
a new group. The keypad will display the following
zone array information for zones 1 to 16.
In the above example screen,
N = Zone 01 and 06 are Normal (Sealed)
S = Zone 02 is Shorted
A = Zone 03,05,07 are in Alarm (Unsealed)
T = Zone 08 is in Tamper Alarm (Unsealed)
- = Zone 04, 09-16 are Disabled (Unused)
MENU 3-0-0
The keypad will display the following zone array
information for Zones 97 to 112.
The keypad will display the following zone array
information for Zones 113 to 128.
3. When finished press [OK] or [MENU] to exit.
Inputs > Commands >
Bypass Zones
This menu allows you to bypass or un-bypass a single or
multiple zones before you turn the area All On, Part On or
MENU 3-0-1
Part 2 On. When bypassing zones, it disables the ability for
a zone to detect intrusion and sound an alarm.
A burglary zone will automatically become un-bypassed
when you turn the corresponding area off (disarm). Any
24-Hr fire or 24-Hr non fire zones will need to be manually
un-bypassed.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [3] + [0] + [2].
A list of zones that can be bypassed will display
on the keypad. A '√' displayed on the right side of
the zone name indicates that the zone is already
bypassed.
Solution 6000
0000000001111111
1234567890123456
NSA-ANAT--------
Press
OK or MENU
9990000000000111 1
7890123456789012 0
---------------- 0
Press
OK or MENU
1111111222222222 1
3456789012345678 0
---------------- 0
Press
OK or MENU
User Guide
MENU 3-0-2
23
Advertisement
Table of Contents
