Subscribe to Our Youtube Channel
Related Manuals for truflo ICON TIR Series
Summary of Contents for truflo ICON TIR Series
- Page 1 TIR SERIES Insertion Paddle Wheel Flow Meters TIR SERIES Insertion Paddle Wheel Flow Meters Operating Manual www.iconprocon.com | sales@iconprocon.com | 905.469.9283...
-
Page 2: Table Of Contents
TIR SERIES Insertion Paddle Wheel Flow Meters Table of Contents Safety Information ® New ShearPro Design Zirconium Ceramic Rotor | Bushings Technical Specifications Long Service Life Pressure vs. Temperature Wiring Diagram Programming Programming NPN Pulse Relay Output Programming NPN Pulse Outputs Programming Relay Option Outputs Reset Flow Totalizer Min | Max | Flow Rates... -
Page 3: Safety Information
Sensor may be under pressure, take caution to vent system prior to installation or removal. Failure to do so may result in equipment damage and/or serious injury Personal Protective Equipmet (PPE) Always utilize the most appropriate PPE during installation and service of Truflo products. www.iconprocon.com | sales@iconprocon.com | 905.469.9283... -
Page 4: New Shearpro ® Design
TIR SERIES Insertion Paddle Wheel Flow Meters New ShearPro ® Design Superhydrophobic Design Contoured Flow Profile Reduced Turbulence Reduced Friction 78% Less Drag than Old Flat Paddle Design* ® ShearPro Competitor 'A' Zirconium Ceramic Rotor | Bushings Industry’s Highest Impact and Chemical Resistant Properties Up to 15x the Wear Resistance vs. -
Page 5: Long Service Life
TIR SERIES Insertion Paddle Wheel Flow Meters Long Service Life Pressure vs. Temperature Note : During system design the specifications of all The TI Series is equipped with a Zirconium Ceramic Rotor Pin components must be considered. | Non-Shock and 2 Bushings. The TI Series also incorporates a contoured, 'Low Drag' Paddle Wheel leading to reduced drag, longer = PVC = PP... -
Page 6: Programming
TIR SERIES Insertion Paddle Wheel Flow Meters Programming DC Power Only STATUS DISPLAY RANGE DESCRIPTION Home Screen 0 - 999.9 Home Screen 3 Secs Press K Factor K Factor Press 0.1 - 99.99 Enter K Factor Value Refer to Chart on Page 7 K Factor Press 4-20mA Output Range... -
Page 7: Programming Npn Pulse Outputs
TIR SERIES Insertion Paddle Wheel Flow Meters Alarm Settings Mode Description ALt.0 No alarm R1 ON R2 ON ALt.1 (AL1-H) AL1 (AL1-H) CV > (AL1) R1/AL1 ON ; CV < (AL1 - H) R1/AL1 OFF CV > (AL2) R2/AL2 ON ; CV > (AL2+H) R2/AL2 OFF R1 ON R2 ON... -
Page 8: Min | Max Flow Rates
TIR SERIES Insertion Paddle Wheel Flow Meters Min | Max Flow Rates Flow Rate (LPM) / USGPM Pipe Size 0.3m/s min. 10m/s max. 2" | DN50 40.0 | 10.5 357.0 | 1350.0 2 ½" | DN60 60.0 | 16.0 1850 | 357 90.0 | 24.0 2800 | 739 3"... -
Page 9: Installation
TIR SERIES Insertion Paddle Wheel Flow Meters Installation Information Very Important Lubricate O-rings with Silicone Retention Cap Locating Pin Ensure O-Rings Using an Alternating | Twisting Motion Carefully Lower the Sensor into are well Lubricated the Fitting. | Do Not Force | Fig 5 Lubricate with Silicone Inside of Insertion Fitting Notch... -
Page 10: Correction Sensor Position
TIR SERIES Insertion Paddle Wheel Flow Meters Correction Sensor Position TI Series Flow Meters measure liquid media only. There should be no air bubbles and the pipe must always remain full. To ensure accurate flow Velocity Flow measurement the placement of the flow meters needs to be adhered .This Profile requires a straight run pipe with a minimum number of pipe diameters distance upstream and downstream of the flow sensor. -
Page 11: Rotor Pin | Paddle Replacement Procedure
TIR SERIES Insertion Paddle Wheel Flow Meters Rotor Pin | Paddle Replacement GENTLY tap Wedge with Tap until Rotor is 50% Out Line up Pin with Rotor Hole Mallet or Hammer Small Pin Spot Point Avoid Damage to 50% Out Pin the Plastic outside Pull out Rotor Pin Insert New... -
Page 12: Dimensions
TIR SERIES Insertion Paddle Wheel Flow Meters Warranty, Returns and Limitations Warranty Icon Process Controls Ltd warrants to the original purchaser of its products that such products will be free from defects in material and workmanship under normal use and service in accordance with instructions furnished by Icon Process Controls Ltd for a period of one years from the date of sale of such products.
Need help?
Do you have a question about the ICON TIR Series and is the answer not in the manual?
Questions and answers