Table of Contents
Advertisement
OWNER'S
MANUAL
MODELNO.
247.795950
Caution:
ReadandFollow
AllSafetyRules
andInstructions
BeforeOperating
This Equipment
i
z
CRRFTSMRN®
5 HORSEPOWER
3 CUTTING STAGE
MULCHING AND BAGGING
CHIPPER-SHREDDER
Assembly
Operation
Customer Responsibilities
Service and Adjustment
Repair Parts
SEARS,ROEBUCK AND CO., HoffmanEstates, IL 60179 U.S.A.
Printed in U.S.A.
770-8473H
1/95
Advertisement
Table of Contents
Related Manuals for Craftsman 247.795950
Summary of Contents for Craftsman 247.795950
- Page 1 OWNER'S MANUAL MODELNO. 247.795950 Caution: ReadandFollow AllSafetyRules andInstructions BeforeOperating This Equipment SEARS,ROEBUCK AND CO., HoffmanEstates, IL 60179 U.S.A. Printed in U.S.A. CRRFTSMRN® 5 HORSEPOWER 3 CUTTING STAGE MULCHING AND BAGGING CHIPPER-SHREDDER Assembly Operation Customer Responsibilities Service and Adjustment Repair Parts...
-
Page 2: Safety Rules
;pair. PREPARATION • Wear safety glasses provided with your unit wh le operat- ing the chipper-shredder to prevent injury from _ny mate- rial which may be ejected out of the openings. • Wear proper apparel. Avoid wearing loose fittin!l clothing. -
Page 3: Product Specifications
Department in the United States. We have competent, well- trained technicians and the proper tools to service or repair this unit. Please read and retain this manual. The instructions will enable you to assemble and maintain your chipper-shredder properly. Always observe the "SAFETY RULES." MODEL NUMBER 247.795950... -
Page 4: Table Of Contents
Fuel ... Lubrication ... These accessories were available when the chipper-shredder Sears retail outlets, catalog and service cel_ters. Most Sears stores can order repair parts for you, when you provide the model number of your chipper-shl edder. ENGINE Muffler Spark ngine... -
Page 5: Unpacking
The hardware pack contains the parts shown in figure Thread 1 (shown full size). TOREMOVE C HIPPER-SHREDDER Cut the corners of the carton. inserts. Roll chipper-shredder certain all parts and literature before the carton is discarded. TOOLS REQUIREDFOR ASSEMBLY (1) Phillips Screwdriver (2) 1/2"... -
Page 6: Assembly
<'-ATTACHING • Remove the hand knobs and cupped washers from each side of the discharge opening on the left side of the chipper-shredder. • Remove hex lock nut, two spacers and hex bolt using two 7/16" wrenches from inside the hinge on top of the housing assembly. -
Page 7: Operation
BEFORE USING YOUR CHIPPER-SHREDDER, PAGE 2 OF THIS MANUAL. ALWAYS BE CAREFUL. The operation of any chipper-shredder result in severe eye damage. Always wear the safety glasses provided with the chipper-shredder shields before chipping or shredding, Wide Vision Safety Mask for over spectacles Stores. -
Page 8: Stopping
MUM) INTO THE HOPPER MATERIAL UP TO A MAXIMUM OF 3" IN DIAMETER BE FED CHIPPER CHUTE. DO NOT ATTEI_IPT TO SHRED OR CHIP ANY MATERIAL LARG- ER THAN 3" IN DIAMETER. INJURY OR DAMAGE TO THE MliCHINE COULD RESULT. -
Page 9: Fuel
Release the bar. See figure 10. FIGURE 10. • Bulky material, such as stalks or heavy branches, up to 3" in diameter, should be fed into the chipper chute. See figure 11. WARNING: MAKE CERTAIN NOT IN USE. -
Page 10: Starting
NENT DAMAGE MAY OCCUR. Fuel Muffler Handle FIGURE 13. TO STARTENGINE & WARNING: BE SURE NO ONE OTHER THAN THE OPERATOR NEAR THE CHIPPER-SHREDDER STARTING OR OPERATING. OPERATE THIS CHIPPER-SHREDDER UNLESS THE CHUTE DEFLECTO:I BEEN PROPERLY INSTALLED SECURED WITH THE HAND KNOB.€;. •... -
Page 11: Customer Responsibilities
CLEANING • The chipper-shredder may be cleaned by running water from a hose through the hopper assembly and chipper chute with the engine running. Allow the chipper-shredder to dry thoroughly. -
Page 12: Spark Plug
FIGURE 18. MUFFLER Do not operate the chipper-shredder or tamper with the exhaust system. Damaged mufflers or spark arresters could create a fire hazard. Inspect periodically,... -
Page 13: Storage
SUCH AS HOT WATER SPACE HEATERS, FURNACES, CLOTHES DRYERS, STOVES, ELECTRIC ETC. NOTE: A yearly check-up by your local Sears Service Center is a good way to make certain your chipper- shredder will provide maximum performance next season. CHIPPER-SHREDDER • Clean the chipper-shredder thoroughly. -
Page 14: Sharpening
Remove the chipper chute by removing three hex nuts and washers. A 1/2" wrench is requi_'ed. See figure 19. NOTE: When reassembling, the cupped washer goes on the bottom of the chipper chute with the cupped side against the chute. • Rotate the impeller assembly... -
Page 15: Adjustments: Carburetor
Your engine attempt to increase engine speed or it may result in personal injury. If you believe the engine is running too fast or too slow, take your chipper-shredder nearest SEARS Service Center for repair and adjust- ment. TIRES (E.G. CARBURE-... -
Page 16: Trouble Shooting
All parts listed herein may be ordered throu(jh Sears, Roebuck and Co. Service Centers Stores. WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: *PRODUCT - "5 H.P. Chipper-Shredder" *MODEL NUMBER - 247.795950 *ENGINE MODEL NO. - 133412-0059-01 *PART NUMBER *PART DESCRIPTION TROUBLE SHOOTING CORRECTIVE Move to ON position. -
Page 17: Repair Parts--Chipper-Shredder
SEARS CRAFTSMAN 5 H.P. CHIPPER-SHREDDER MODEL NO. 247.795950 Repair Parts... - Page 18 Hex Bolt 5/t6-18 x .7,_ Lg. (Gr. 5) l-Incl. Ref. 1,6, 7, 8, 9, 10, 11, 12, 13, 14 *Common Hardware--May Be Purchased Losally. NOTE" Specifications subject notice or obligation. MODEL NO. 247.795950 PART 710-0380 681-0004 781-0474A 735-0639 I.D. x .25" 133412-0059-01...
- Page 19 BRIGGS AND STRATTON Repair Parts REF. PART DESCRIPTION 495133 Cylinder Assembly 399268 Bushing--Cylinder *299819 Seal--Oil 214040 Head--Cylinder *272157 Gasket--Cylinder Breather--Valve 495774 *27549 Gasket--Valve 94621 Screw--Breather Grommet--Breather 66578 94221 Screw--Cylinder Long) 94167 Stud--Cylinder 94679 Screw--Cylinder Long) 94387 Plug--Pipe, 1/4" Std., Square Head 223886 Guide--Air 494906...
- Page 20 BRIGGS AND STRATTON Repair Parts REF. PART DESCRIPTION *270080 Gasket--Crankcase Std.) *270125 Gasket--Crkcse. *270126 Gasket--Crkcse. 495845 I Crankshaft Note: To Replace Cranks _aft Gear Pin--Order 493916 Cover Ass'y.--Crankcase 495660 Bushing_rankcase 495307 Seal--Oil 66768 Plug--Oil Filler 94682 Screw--Crankcase Mounting Sem 222698 Key--Flywheel 393819 Piston Ass'y.
- Page 21 BRIGGS AND STRATTON Repair Parts REF. PART DESCRIPTION *272295 Gasket--Carburetor *272585 Gasket--Intake 94706 Screw--Adapter Screw--Round 94098 398185 Screw--Idle Pin--Hinge 224783 Valve--Choke 262820 Spring--Lever Gasket--Sealing (Sold in Kit Only) *493765 Valve and Spring--Needle 94681 Screw--Hex 495652 Carburetor Assembly Plug--Welch 223470 Valve---Throttle 493556 Shaft and Lever--Throttle 398187...
- Page 22 BRIGGS AND STRATTON Repair Parts REF. PART DESCRIPTION 224709 Bracket--Fuel 93559 Screw--Hex 94010 Nut--Hex 393815 Line-Fuel (11" Long, Cut to Suit) 187A 495218 Pipe--Fuel (Molded) 94357 Screw--Hex 281190 Cover--Spark 93053 Clamp---Fuel Note: 93807 Clamp--Fue (Black) 493988 Cap-Fuel Tank 494539 Valve Ass'y.--Fuel 495345 Tank Ass'y.--Fuel * Included in Gasket Set--Part...
- Page 23 BRIGGS AND STRATTON Repair Parts REF, PART DESCRIPTION 297229 Flywheel--Magneto 222443 Guard--Flywheel 224633 Screen--Rotating 494790 Housing--Blower 94619 Screw--Blower 92284 Nut--Flywheel 397358 Armature Group 93414 Screw--Armature 495135 Wire Assembly (Armature to Switch) 495118 356A Wire Assembly (Stop Switch to Ground) 19069 Puller--Flywheel Hub--Starter 494770...
- Page 24 3u..."we service what we sell." Par_ obtener un manual de operador Ilanle al 1 800 800-7310 770.8473H para modelo 247.795950. CO., Hoffman Estates, IL number. Each will be found will be found on the be ordered...