Table of Contents
Advertisement
Spacers:
Housiltg
Assem aly
13olt
He](
Nut
3hute
D .=flector
Hand
Knob
FIGURE 2.
Stop
Hopper
!-_F--_
Washer
Pivot _
"_/_
_o
Door
//_
/
"_'_Y_\
/! II II11 !
\/
3pper
//
t l /l_'_ I
_
_uiae
//
_,-_\_
_
Release
A.,;sembly
t/
,_ _t_ J
I \llll _
Bar
II
/Jill
X HexBolt
///
I \\1
fill
8-3/8"Long
II/
Inset
\\1 °Ill Y
Flat Washer
///
Guide
_
Hex Lock Nut
FIGURE 3.
Hopper Pivot
Hopper Asstimbly
Door
Bar
Guide
Assembly
t l pper
Leaf
Ilamp
S .=ction
Remove T russ
Screw ant Nut
(Asseml de
First)
FIGURE 4.
Drawstr ng
.Plunger
FIGURE 5.
HOW TOSET-UP YOURCHIPPER-SHREDDER
,_
MAKE
CERTAIN
THE
SPARK
PLUG
WIRE IS DISCONNECTED
AND MOVED
AWAY
FROM
THE
SPARK
PLUG
BEFORE
ASSEMBLING
THE CHIPPER-
SHREDDER.
REFER
TO FIGURE
13,
PAGE 10.
<'-ATTACHING
THE CHUTE DEFLECTOR
• Remove the hand knobs and cupped washers from
each side of the discharge opening on the left side
of the chipper-shredder.
•
Remove hex lock nut, two spacers and hex bolt
using two 7/16" wrenches from inside the hinge on
top of the housing assembly.
Do not remove one
spacer from the hex bolt.
•
Place the chute deflector
in position on the dis-
charge opening. Insert hex bolt and spacer through
hinge on chute deflector and housing (spacer fits
inside of hinge). See figure 2.
• Place second spacer over hex bolt, inside other
part of hinge. Secure with hex lock nut. Tighten
securely.
• Secure both sides of chute deflector
to housing
using hand knobs and cupped washers (cupped side
of washers go against chute deflector).
_-ATTACHING
THE UPPER GUIDE ASSEMBLY
Grasp the upper guide assembly from the sides and
squeeze
in and slide it over the inlet guide so the
edges are under the stop washers.
Adjust
so the
holes in the upper guide assembly
are aligned with
the holes in the inlet guide. Insert the hex bolt, 8-3/8"
long through the upper guide assembly and the inlet
guide. Secure with flat washer and lock nut.
NOTE: Make certain the upper guide assembly
can
pivot by lifting it up until it locks in the raised position.
If it does not pivot freely, loosen the hex lock nut a
turn or two and test.
<-ATTACHING
THE HOPPER ASSEMBLY
Your chipper-shredder
has been shipped
with the
upper
leaf ramp section
attached
to the hopper
assembly. See figure 4. Attach the hopper assembly
to the upper guide assembly as follows. Be certain to
place heads of all truss machine
screws inside
of
hopper assembly.
•
Remove one truss machine
screw and nut from
each side of hopper assembly as shown in figure 4.
Push hopper pivot door down inside lower part
of hopper
as you place hopper assembly
(both
pieces)
inside
upper guide assembly.
Replace
truss screws and nuts just removed, using the hole
shown in figure 4, one on each side. Tighten finger
tight only.
NOTE: You may have to squeeze in the sides of the
hopper to start the screws.
NOTE: If you have difficulty aligning the hole, loosen
the two screws
on the upper
end of the hopper
assembly.
• Place the six truss machine screws and nuts found
in hardware pack in the remaining holes of hopper
assembly, alternating sides of the unit and tighten-
ing finger tight only.
• After assembling
all eight screws,
tighten
them
securely.
<-ATTACHING
THE CATCHER BAG
Your chipper-shredder
is equipped with a catcher bag
to catch the shredded material.
Hide quick links:
Advertisement
Table of Contents
