Related Manuals for TASKING iSYSTEM ST SPC58 4B
Summary of Contents for TASKING iSYSTEM ST SPC58 4B
- Page 1 ST SPC58 4B Line Emulation Adapter Hardware User Manual V2.2, September 2023 isystem.com/start...
- Page 2 General safety instructions Please read the following safety precautions carefully before putting this device to use to avoid any personal injuries, damage to the instrument, or to the target system. Use this instrument only for its intended purpose as specified by this manual to prevent potential hazards. Use included power cord and power supply The enclosed power supply has been approved for use by iSYSTEM.
-
Page 3: Table Of Contents
Contents Introduction ............................4 Package content ..........................5 Adaptation packages content ......................6 Operation ............................... 7 Adaptation setup ............................. 8 Screws ............................................... 9 Configuration ............................10 Connectors .............................. 13 Power supply package ......................... 14 Standalone operation ........................... 15 Measurement board ..........................16 Mechanical information ...................... -
Page 4: Introduction
Introduction ST SPC58 (Chorus) 4B Line Emulation Adapter primary use case is providing Nexus trace functionality for the SPC58 4B Line devices in the QFP packages, where Nexus trace port is not available. It is based on the 176-pin "superset" device with 2MB program and provides the adaptation to: ·... -
Page 5: Package Content
Package content ST SPC58 C line Emulation Adapter is delivered with all components required for Standalone operation. Adaptation packages for Target board adaptation must be ordered separately. Power supply package ST SPC58 4B Line Emulation Adapter Power converter Power adapter Ordering code: Ordering code: Ordering code:... -
Page 6: Adaptation Packages Content
Adaptation packages content Conversion boards connect between the Emulation Adapter and the matching Solder part which is being soldered on the Target side. Pin number Conversion Board Type Solder part IEA-SPC584B-ATQ64 Fixed IA64ATQ-SOLDER IEA-SPC584B-TQ100 Fixed IA100TQ-SOLDER IEA-SPC584B-TQ144 Fixed IA144TQ-SOLDER Fixed Adaptation This adaptation is delivered with a slot screw, which can be optionally used to achieve a more solid and stable fixing of the Conversion board and the Solder part. -
Page 7: Operation
Operation Device overview The Emulation Adapter can be used in conjunction with iSYSTEM iC5000 and iC5700 BlueBox or any other third party tool supporting ST SPC58 4B Line Nexus trace port. The tool connects to 38-pin Mictor connector (P1) providing debug and Nexus trace interface connection. Emulation Adapter offers the following adaption setup: ·... -
Page 8: Adaptation Setup
Adaptation setup Fixed Adaptation... -
Page 9: Screws
Screws Slot screw The Slot screw (30mm) is used to fix the Conversion board to the Solder part. The setup becomes mechanically more robust.Screw the Conversion board to the Solder part first, before the Emulation Adapter is attached on top and watch out not to break out the Solder part, e.g., if you accidentally hit the Emulation Adapter from the side. -
Page 10: Configuration
Configuration J1: Target reset configuration Jumper J1 connects the reset line between the emulation device and the target. By default J1 is populated. J2 and J3: Clock source configuration Jumpers J2 and J3 select external clock source (XOSC) for the emulation device. Per default, both jumpers are set to position 1-2, which yields the external clock (XOSC) source being used from the target. - Page 11 Capacitors C50 and C51, for which pads are provided on the emulation adapter PCB, are not populated since the microcontroller provides already internal load capacitors for 20MHz/40MHz crystal oscillator operation. J4 and J5: GND connecting points Real target microcontroller in the QFP package provides an exposed GND pad in the middle of the microcontroller at the bottom side of the package.
- Page 12 P2: Power supply configuration EA Power supply is configured via the unshrouded 26-pin 2.54 mm header (P2). Signal direction Signal Signal Signal direction Not connected Not connected Target VDD_HV_OSC CVDD_HV_OSC Emulation device Target VDD_HV_ADV_S CVDD_HV_ADV_S Emulation device Target VDD_HV_ADR_C CVDD_HV_ADR_C Emulation device Target VDD_HV_IO_MAIN...
-
Page 13: Connectors
Connectors P1: Nexus trace port 38-pin Mictor connector P1 exposes Nexus trace port and has the following pinout: Signal Signal MDO9 MDO8 RSTIN EVTIN Vref MDO10 MDO7 MDO6 MDO5 NTRST MDO4 MDO11 MDO3 MDO2 MDO1 MDO0 EVTO MCKO MSEO1 MSEO0 38-pin Mictor pinout Signal Direction is described from the BlueBox perspective. -
Page 14: Power Supply Package
Power supply package A Power supply package, which is delivered with the Emulation Adapter, is required when: · The Emulation Adapter is used as a standalone device . · The target board doesn’t provide an accurate supply voltage. · The target board doesn’t provide sufficient current for the Emulation Adapter operation. The Power converter can supply either 3.3 V or 5 V. -
Page 15: Standalone Operation
Standalone operation Emulation Adapter is delivered with all components required for a Standalone operation. Power supply Use enclosed IEA-PS Emulation Adapter Power converter. -
Page 16: Measurement Board
Measurement board With the Measurement board you gain easy access to all MCU pins respectively, because modern targets do not have accessible all the MCU pins / connected signals to connect with a measurement equipment (oscilloscope, logic analyzer). The Measurement board is optional and connects between the Emulation Adapter and the Conversion Board. -
Page 17: Mechanical Information
Mechanical information Solder part solder pad view Top view of the Solder part Side view of the Solder part Side view of the Emulation adapter complete setup - QFP Fixed Adaptation Top view of the Emulation Adapter Top view of the Conversion board... - Page 18 Solder parts In case of soldering the Solder part manually, it’s highly recommended prolonging the solder pad E on the outer side (e.g., for 1.5-2 mm) during the PCB design. Note that without this modification, it’s very difficult to solder the Solder part manually. Recommended PCB footprint dimensions: Unit (mm) IA64ATQ-...
-
Page 19: Connectors P3-P6 Pinout
Connectors P3-P6 pinout Next picture shows a pinout of the four connectors P3-P6 on the bottom side of the EA. nc – Not Connected Optionally, the you could also design the target directly providing connection to the EA via P1- P4 connectors. - Page 20 Visit our website for: · Support - isystem.com/support · Tutorials - isystem.com/start · Knowledge Base - kb.isystem.com www.isystem.com...