Webs-Ax Security Enclosure - Honeywell SEC-H-602 Manual

SEC-H-602 AND SEC-H-616 SECURITY CONTROLLER

WEBs-AX Security Enclosure

The Security Controller and all expansion modules must
be mounted in one or more WEBs-AX Security
Enclosures. These enclosures have a pre-mounted DIN
SEC-ENC-H-1/U
INTEGRAL
30W
15VDC
PS
AC LINE
35MM DIN RAIL
INPUT
120-
240VAC
BATTERY SPACE
MINIMAL SYSTEM CONFIGURATION
INTEGRAL
30W
15VDC
PS
12V BACKUP
BATTERY
1 INTERCONNECTING CABLES NOT SHOWN.
2 IN LARGER SYSTEMS, ADDITIONAL UNPOWERED ENCLOSURES CAN BE USED FOR MODULES ONLY (NO SECURITY CONTROLLER),
WHERE BACKUP BATTERIES ARE NOT USED. AT RIGHT AN SEC-ENC-H-1 IS USED THIS WAY.
Fig. 2. Security Controller must be mounted in WEBs-AX Security Enclosure (model SEC-ENC-H-1/U or SEC-
As shown in Fig. 2, there are 3 different-sized WEBs-AX
Security Enclosures available, including these models:
SEC-ENC-H-1/U:
(Medium) For the Security Controller
in the smallest job configuration, or where additional
expansion modules are located remotely (in other
Security Enclosures). It provides a single DIN rail and an
integral 30W 15Vdc power supply to power the controller.
The controller (or modules) plug directly into the power
supply, see Fig. 2. Brackets at the bottom of the enclosure
secure one or two rechargeable sealed lead-acid backup
batteries; more unpowered Security Enclosures can be
used to house additional expansion modules.
Another medium-sized enclosure without an integral
power supply is also available, model SEC-ENC-H-1NP/
U. It is used for expansion modules only (not the Security
Controller), and it has room for one additional SEC-H-
R2R/U module.
SEC-ENC-H-2/U:
(Large) Used for the Security
Controller in larger job configurations, it provides a DIN
rail mount and an integral 30W 15Vdc power supply for
the controller, and a second DIN rail for expansion
31-00012—03
15VDC OUTPUT
INTEGRAL
SECURITY
CONTROLLER
BATTERY
SPACE
2
rail (or rails), and include a door with a key lock and
tamper switch. Two models have an integral 30W 15Vdc
power supply that powers the security controller and/or
the expansion modules inside the enclosure.
SEC-ENC-H-2/U
15VDC OUTPUT
30W
15VDC
PS
35MM DIN RAILS (2)
BATTERY SPACE
SEC-ENC-H-1NP/U
(2)
SEC-H-RIO/U
SEC-H-R2R/U
UNUSED UNUSED
SPACE SPACE
ENC-H-2/U).
modules—for example, up to four (4) SEC-H-R2R/U
modules. The security controller plugs directly into the
power supply, see Fig. 2. A supplied six-conductor wiring
harness (not shown) provides power and RS-485
communications to expansion modules mounted on the
lower DIN rail. Brackets at the bottom of the enclosure
secure one or two rechargeable sealed lead-acid backup
batteries (backup batteries used only if enclosure houses
an Security Controller). In larger systems, more Security
Enclosures can be used to house additional modules.
Another large-sized enclosure without the integral power
supply is also available, model SEC-ENC-H-2NP/U. It is
used for expansion modules only (not the Security
Controller), and it has room for one additional SEC-H-
R2R/U module.
SEC-ENC-H-3/U:
used only for one SEC-H-R2R/U module—it has no
integral power supply or backup battery area. See Fig. 2
When wiring back to the Security Controller, you must use
a 3-conductor cable for power/battery backup (PS-, PS+,
BB), in addition to RS-485 wiring.
4
LARGER SYSTEM CONFIGURATION
INTEGRAL
30W
SECURITY
15VDC
CONTROLLER
PS
SEC-H-RIO/U
SEC-H-R2R/U
12V BACKUP
BATTERY
1
SEC-ENC-H-3/U ONLY APPLICATION
35MM
DIN RAIL
(Small) Has a single DIN rail, and is
(2)
12V BACKUP
BATTERY
SEC-H-R2R/U
M35012