Finish Thompson PF Series Operation-Installation-Parts Manual
Hide thumbs
Also See for PF Series:
- Operations & parts manual (19 pages) ,
- Operation-installation-parts manual (12 pages)
Related Manuals for Finish Thompson PF Series
Summary of Contents for Finish Thompson PF Series
- Page 1 PF SERIES PUMPS PFM, PFP, PFV OPERATION, INSTALLATION & PARTS MANUAL P/N 108097 R8...
-
Page 2: Eu Declaration Of Conformity
EU Declaration of Conformity Finish Thompson Inc. hereby declares that the following machine(s) fully comply with the applicable health and safety requirements as specified by the EU Directives listed. The product may not be taken into service until it has been established that the drive motor for the centrifugal pump complies with the provisions of all relevant EU Directives. -
Page 3: Declaration Of Conformity
Declaration of Conformity Finish Thompson Inc. hereby declares that the following machine(s) fully comply with the applicable health and safety requirements as specified be the UKCA Directives listed. The product may not be taken into service until it has been established that the drive motor for the Drum and Container Pump complies with the provisions of all relevant UKCA Directives. - Page 4 Introduction This manual pertains to the PF Series, specifically the PFP, PFM, and PFV plastic drum pumps and accessories. Finish Thompson Inc. thanks you for choosing our products. We believe the use of our products will be fully satisfactory. When properly installed and operated, your Finish Thompson motor and pump will provide long, trouble-free service;...
-
Page 5: Warranty, General Terms & Conditions
Warranty Registration Thank you for your purchase of this quality Finish Thompson product. Be sure to take a minute to register your pump at Finishthompson.com/warranty. Simply provide the model number, serial number and a few... -
Page 6: For Your Own Safety
The personnel in charge of the installation, the operation, and the maintenance of the pump must be qualified and able to per- form the operations described in this manual. Finish Thompson, Inc. shall not be held responsible for the training level of personnel and for the fact that they are not fully aware of the contents of this manual. - Page 7 IMPORTANT SAFETY INFORMATION FOR PUMPING FLAMMABLE OR HAZARDOUS SUBSTANCES Read these instructions before operating the pump and motor equipment. The manufacturer will not be responsible for any damage to property or to persons caused by improper use of the equipment. WARNING: It is the responsibility of the user to operate the pump in conformance with OSHA rules for dispensing liquids.
-
Page 8: Pump Specifications
13-JUN-2022 THIS DRAWING IS THE PROPERTY OF FINISH THOMPSON, INC. AND EMBODIES A CONFIDENTIAL PROPRIETARY DESIGN IN WHICH FINISH THOMPSON, INC. RETAINS ALL PATENTS AND PROPRIETARY RIGHTS, INCLUDING EXCLUSIVE RIGHT OF USE, MANUFACTURE AND SALE. BY ACCEPTING THIS DRAWING, THE RECIPENT AGREES NOT TO DISCLOSE,REPRODUCE OR USE ANY INFORMATION CONTAINED HEREIN WITHOUT THE PRIOR WRITTEN CONSENT OF FINISH THOMPSON, INC. -
Page 9: Installation
Note: ALWAYS use a 1”(25mm) I.D. hose properly secured to the barb spout using a hose clamp. Torque Finish Thompson hose clamps to 25 in-lbs(2.8 N·m). Operation 1. Make sure the motor (electric or air) is properly installed on the pump tube and is in the off position. See motor instruction manual for motor installation instructions. - Page 10 3. Remove the impeller housing (item 14) by gripping the intake tube and spinning the housing clockwise (left hand thread). 4. Place a wooden board or rubber mat on the floor (to protect threads on the bottom of the shaft) and gently tap shaft (item 14) on it until the bearings (item 3) are exposed at the top of the pump.
- Page 11 PFM/PFP/PFV SPARE PARTS EXPLODED VIEW...
-
Page 12: Pump Spare Parts List
PUMP SPARE PARTS LIST PART NUMBER ITEM DESCRIPTION MODEL PFM MODEL PFP MODEL PFV COUPLING INSERT NITRILE J100014 J100014 J100014 COUPLING HALF CAST ALUMINUM 1/4”-20 THREAD FOR S/N 211770 & UP J100012-2 J100012-2 J100012-2 BEARING ASSEMBLY (INCLUDES COUPLING HALF) STEEL A101110 A101110 A101110... - Page 13 PART NUMBER ITEM DESCRIPTION MODEL PFM MODEL PFP MODEL PFV HOUSING COVER POLYPROPYLENE M101612-1 M101612-1 PVDF M101612-2 DISCHARGE O-RING FKM (STANDARD) J100991 J100991 J100991 EPDM J102378 J102378 J102378 FFKM 107017 107017 107017 DISCHARGE NUT FOR USE WITH 1” OR 3/4” BARB SPOUT & GARDEN HOSE M101610-1 M101610-1 M101610-2...