Specifi Cations; Troubleshooting - NEC MD215MG-S5 Installation & Maintenance Manual

21" grayscale 5-megapixel medical diagnostic monitor
Hide thumbs Also See for MD215MG-S5:
Table of Contents

Advertisement

Specifi cations
Monitor Specifi cations
LCD panel color
LCD
Pixel pitch (H x V)
Display area (H x V)
Pixel (H x V)
Grayscale
Backlight
LCD Optical characteristics (typ.)
Luminance
Input sync signal
Available resolution
Input connectors
USB Hub
Ambient conditions
Temperature:
Humidity (no condensation):
Air pressure:
Power
AC Adapter MW122:
Power consumption
Power saved:
Dimensions & weight
(W x H x D)
Safety certifi cations
NOTE:
Technical specifi cations are subject to change without notice.

Troubleshooting

The display won't turn on! (The power indicator is off.)
Make sure the display is plugged.
Check to see if the display is turned on.
The screen is not lit!
Check if cables are connected correctly.
Check if the computer is turned on.
If the LED indicator is orange, the computer may be in power saving mode. Press any key on the keyboard to wake up
the computer.
The input signal frequency or display resolution may not be appropriate for the display. Refer to the computer instruction
manual and adjust the frequency and/or resolution.
If the LED is red, this may be an error indication. Contact your supplier.
Images are not displayed properly!
The display resolution may not be appropriate for the display. Refer to the computer instruction manual and adjust
resolution.
The refresh rate is set to 50Hz (dual-link mode) and resolution loss (scan line gaps) occurs!
This can happen when a single-link cable or a DisplayPort to Single Link adapter is used. Use the supplied dual-link
cable which supports both single-link (25Hz) and dual-link (50Hz) modes, or set the refresh rate to 25Hz.
MD215MG
Clear Base
21.3-inch (54 cm), monochrome, TFT active matrix, anti-glare
0.165 x 0.165 mm
337.9 x 422.4 mm
2048 x 2560
256 steps of gray out of a palette of 3826
10-bit (1024) simultaneously displayable grayscale in packed pixel mode
12 cold cathode fl uorescent lamps (CCFL)
Viewing angle: 170° horizontal/vertical (contrast ratio ≥ 20:1)
Contrast ratio: 850:1 (Viewing angle perpendicular to LCD panel)
DICOM calibrated
Maximum
DVI 1.0 compliant
640 x 480
800 x 600
1024 x 768
2048 x 2560 (at Fv=25/50Hz)
2560 x 2048 (at Fv=25/50Hz)
DVI 24-pin connector, 6-pin DC power input terminal
USB Rev. 2.0 compliant, Self-powered
USB upstream port (x1), USB downstream ports (x2)
On: 5 ~ 40°C, Off: -20 ~ 60°C
On: 30 ~ 80%, Off: 10 ~ 85%
On: 700 ~ 1060hPa, Off: 266 ~ 1060hPa
Display:
DC 12V, 10A
Input: AC 100 to 240V, 50/60 Hz, 2A
Output: DC 12V, 10A
Normal:
Approx. 90W (w/ supplied AC adapter)
Less than 10W (w/ supplied AC adapter)
Net:
390 x 487.8/584 x 227.6 mm (W x H x D: Portrait) approx. 11.1 kg
Packed:
475 x 705 x 345 mm (W x H x D). approx. 15 kg
UL60601-1, CSA C22.2 No.601.1, FCC-B, CE-MDD, VCCI-B
English-11
Notes
2
400 cd/m
as factory default
2
2
500 cd/m
(1100 cd/m
typ. as LCD component)

Advertisement

Table of Contents
loading

This manual is also suitable for:

Mdg5-bndl1Md215mg

Table of Contents