Patpet p-collar 640, p-collar 640B SetUp and Pairing

Overview

Remote

Selecting Channels
Quick selection for the certain dog we want to train.

Touch Distinguishing Edge
Effectively preventing unexpected operation and avoiding unintended training.

White Backlit LED Display
Indicating intensity level under any circumstances of visibility.

Blind Operation Buttons
Easily distinguish and send the correct training command without eyes on by touching and feeling on buttons with different patterns.

Receiver

Setting Up the Product

Before you can use the Dog Training Collar, you must set up the product following the steps below:

1. Prepare the Remote: install the antenna and turn the Remote on.
2. Charge the Remote and the Receiver.
3. Prepare the Receiver: install contact points, conductive silicone, and turn the Receiver on.
4. Function test: Test function of buttons before putting it on the dog.
5. Use the Test Lamp to test shock function or use as a screw driver.
6. Pair the Remote and the Receiver, pair them when the product loses its code or pair a second collar.

Step 1 Charging the battery

The unit uses Lithium-Polymer batteries.

1. Charge the unit before using the unit for the first time.
2. Do not charge the batteries near any flammable substances.
3. Fully charge the batteries if the unit is to be stored without use for a period of 3 months or more.

The unit need to be charged under any of the below situations:

1. The indicator light on the collar is emitting a red color and flashes rapidly.
2. The 3 bar indicator on the Remote LCD shows just 1 bar.
3. The indicator light on the Remote or Receiver will not come on.
4. The indicator light on the Remote or Receiver comes on momentarily when any of the Mode Buttons are pressed.

Battery Charging Procedure.

NOTE: The unit has a partial charge when it leaves our facility, upon receipt of the collar, be sure to give it a 4-hour initial charge before the first use.

1. Lift the rubber covers protecting the Remote and Receiver Charging Jack.
2. Connect the charger connectors to the Remote and Receiver Charging Jack, as shown below.
3. Plug the charger into a standard wall outlet.
4. Connect the USB port to the Charging Adapter.
5. Charge the unit for 4 hours for the first charge. Recharges take only 2-3 hours.
6. When charging is completed, remove the charger connector, and replace their rubber covers.

Note: The Battery Indicator on the Remote will scroll and the indicator light will be steady red while charging; The Battery Indicator will become steady, and the LED Indicator Light will flash when fully charged. The indicator light on the Receiver will be steady red while charging and green when fully charged.

Step 2 Prepare the Remote

1. Install the antenna tightly to the corresponding position of the Remote tightly.
   
2. Press Tone/Vibra/Shock button on the Remote. The white backlight on the display stays on for approximately 5 seconds after a button press. After that if not button is pressed within 25 seconds, the white backlight will shut off first, the display will shut off and the Remote will go into battery conservation mode.
3. Pressing Tone/Vibra/Shock button will turn the display back on.

Step 3 Prepare the Receiver

Install the Contact Points & Conductive Silicone

1. Select the correct Contact Points and Conductive Silicone length for your dog's coat type:
   • For dogs with thicker coats, Use 2pcs longer Contact Points and Conductive Silicones.
   • For dogs with shorter coats, Use 2pcs shorter Contact Points and Conductive Silicones.
2. Insert the Contact Points into the ports of the collar, rotate clockwise to tighten them.
3. Install the Conductive Silicone onto the Contact Points to make the contact softer so it is better for the dog's skin.

Turn on the Receiver

• Press the On/Off Button until the Green LED light comes on. In normal mode, the Green LED will flash every 4 seconds, indicating the Receiver is on and ready to receive a signal from the Remote.

Turn off the Receiver

1. Press and hold the On/Off Button until the Red LED flashes rapidly then shuts off. (This takes approximately three seconds.)
2. Release the On/Off Button.

Note: To extend the life of the batteries, turn the Receiver off when it is not in use.

Step 4 Function test

We recommend you experience firsthand how the different levels feel on yourself and always begin at the lowest level, and increase the levels up to your personal comfort levels.

1. Place one finger over both contact points of the training collar.
2. Hold your remote approximately 2 ft. from the training collar. Press the vibration button continuously for 1 to 2 seconds. You should feel continuous vibration.
3. Starting at level 1 for shock, Press the shock button.
4. Increase the level until the sensation begins to feel uncomfortable.

NOTE: Continuous stimulation will transmit for no more the 10 continuous seconds. To reactivate, release and repress the button.

1. Dog 1/2 Toggle
2. Up/Down Button
3. TONE Button (Grey with Bar)
4. VIBRA Button (Yellow with Dot)
5. SHOCK Button(Black with Bar)

Tone Only Button (Grey with Bar):
Sends an audible tone to the collar. No stimulation is delivered.

Vibration Only Button (Yellow with Dot):
Sends 1 non-adjustable level of vibration stimulation to the collar.

Shock Only Button (Black with Bar):
Delivers shock through the Contact Points on the Receiver at the level shown on the Digital Display. When held down for 10 consecutive seconds, the Remote will "time-out", and shock cannot be delivered for 5 seconds. You must release and press the button again after the 5 seconds time-out period, before additional shock can be delivered.

Dog 1/ 2 Toggle Switch

Located on the upper left face of the Remote is a toggle switch, allowing you to switch between Dog 1 and Dog 2.
Shock Up/ Down Button: To adjust shock Intensity Level from 1 to 16.

	Vibration: Sends 1 non-adjustable level of vibration stimulation to the collar.
	Tone: sends a tone with non-adjustable level to the Receiver.
	Shock: sends 1-16 adjustable levels of static stimulation to the Receiver.
	Press to increase the shock level.
	Press to decrease the shock level.

Note:

• The shock level can be adjusted from 1 to 16 levels; please adjust it properly as per your dog's reaction.
• It is not recommended to press and hold the Vibration / Shock Button too long to avoid physical or psychological hurt to the dog.

Step 5 How to Use the Test Lamp

Shock Function Test

1. Turn on the Receiver.
2. Hold the Test Lamp contacts against the Contact Points(or Conductive Silicone).
3. Press the Shock Button and the Test Lamp will be lighted. It will be brighter as the shock level increases.

As a Screw Driver

Use the Test Lamp to tighten or loosen the Contact Points when preparing the Receiver.

Step 6 Patpet p-collar 640/640B Pair the Remote and the Receiver

If your Receiver does not beep when the TONE Button of the Remote is pushed, or if you feel the Receiver is not responding to the Remote, follow these steps to pair:

1. Take the Receiver off of your pet. Turn the Receiver off. Restart, press and hold the On/Off Button until the green, Red LED flashes alternately. Hold for 30 seconds, within which pairing should be completed.
2. Press and hold the TONE and VIBRA button on the Remote at the same time until the Green LED light on the Receiver flashes rapidly for 5 times, indicating pairing is completed.

Two Dog System

NOTE: If you wish to add another Receiver Collar to the training system, please buy the same model receiver.

Remote Transmitter

1. Switch Dog1 to Dog2 by short pressing the button -1/-2.
2. Turn on the Receiver Collar for Dog 2, then repeat the pairing steps above.
3. If Dog 2 Receiver does not respond. Pairing may be needed.
   Repeat steps in Pair the Remote and the Receiver above.