Patpet No Bark Collar A12 Manual

Introduction

Please read the user's manual before beginning. Please read the user manual before using_.
The A12 No Bark Collar is designed to let dogs live safely, happily and get along with people more harmoniously.

Do not use with aggressive dogs.
Aggressive dogs can cause severe injury and even death to their owner and others. If you are unsure whether this product is appropriate for your dog, please consult your veterinarian or certified trainer.

Safety during on-leash training.
It is vitally important that you and your dog remain safe while anti-barking training. Your dog should be on a strong leash, long enough for him to attempt to chase an object, but short enough for him not to reach a road or other unsafe area. You must also be physically strong enough to restrain your dog when he tries to chase.

Risk of skin damage.

Please read and follow the instructions in this manual.
Proper fit of the collar is important.
A collar worn for too long or made too tight on the pet's neck may cause skin damage ranging from redness to pressure ulcers.
This condition is commonly known as bed sores.

• Avoid leaving the collar on the dog for more than 12 hours per day.
• If possible please change the collar position on the dog's neck every 1 to 2 hours.
• Never connect a lead to the electronic collar; it will cause excessive pressure on the contacts.
• If rash or sore found, stop using the collar until the skin heals. If the condition persists beyond 48 hours, see your veterinarian.
• This product is not a toy, please keep away from children.
• This product is only applied for healthy dog.

Overview

Setting Up the Product

Before using the collar, you must set up the collar by following steps:

Charging to the Collar

1. For the first charger, make sure to charge it for 4 hours. Subsequent charging only take 2-3 hours.
2. The screen will display "" while charging, and flash every 4 seconds. When fully charged, the screen will display "".
3. Please replace the rubber cover when the collar is full charged.

Tips:

Note:
Please use the Output: DC 5V 500-800mA charger to charge the product.
Don't use a charger that does not meet the specifications to charge the product.

Prepare the Collar

Turn on the Collar

• Press the button and the screen turns on.
• The screen will display the last user-set level by default.

Turn off the Collar
Press and hold the button until the screen turns off. (This takes about 3 seonds).

Adjustable Collar
Please refer to the steps to set up and adjust the collar.

Function Test

We recommend that you perform a functional test before using the A12 collar.

Automatic Mode

Vibration Mode

Beep Mode

1. If there are no more than 6 barks within 30s, the timer will end.
2. If the 7th bark is detected within 30s, it will stop working for 30 seconds then continue to work.

Shock Mode

• The first bark detected---vibrate once, and start timing at the same time.
• The second bark detected---shock(level setting) once
• The third bark detected---shock(level setting) once
• 2s later, the fourth bark is detected---shock(level setting) once
• And so on

1. If there are no more than 6 barks within 30s, the timer will end. Then repeat the above operation.
2. If the 7th bark is detected within 30s, it will stop working for 30 seconds then continue to work, repeat the above operation.

Collar Fitting

Please fit the collar properly to avoid over tight for the dog. When properly fitted, you could put a finger between the collar and the dog's neck.

Too loose:
The collar will move around the dog's neck, thus the shock stimulation cannot work effectively.

Too tight:
It may cause the dog to have difficulty breathing.

1. Do not shave the hair off the dog's neck as this may increase the risk of skin irritation.
2. The collar should not be worn for more than 12 hours per day. Or it may cause skin irritation.

Device Information

Product Specifications

The unit need to be charged under any of below situations

The R&D of Anti-Barking Collar
https://patpet.us/
service@patpet.com
@PatpetTech
1-855-888-9922

Shenzhen Patpet Technology Co.,Ltd
Add: No.1 Qinhui Road, Gushu Community,
Xixiang Street, Baoan District, Shenzhen, China