PATPET p-collar 356 - Dog Training Collar Manual

Package Contents

Overview

Hand Remote

Display Screen

Receiver Collar

Important Safety Information

This is the safety alert symbol. It is used to alert you to potential injury hazards. Obey all safety messages that follow this symbol to avoid possible injury.

Not for use with aggressive dogs. Do not use this product if your dog is prone to aggressive behavior. Aggressive dogs can cause severe injury to their owners and others. If you are not sure if this product is right for your dog, please check with your veterinarian or a certified trainer.

Safety during on-leash training
While learning during on-leash training. Your dog should be on a strong leash, long enough for him to attempt to chase an object, but short enough for him not to reach a road or other unsafe area. You must also be physically strong enough to restrain your dog when he tries to chase.

Risk of skin damage
A collar worn for too long or made too tight on the pet's neck may cause skin damage ranging from redness to pressure ulcers. This condition is commonly known as bed sores.

• Avoid leaving the collar on the dog for more than 8 hours per day.
• When possible reposition the collar on the pet's neck every 1-2 hours
• Never connect a lead to the electronic collar, it will cause excessive pressure on the contacts.
• If a rash or sore is found, discontinue use of the collar until the skin has healed.
• If the condition persists beyond 48 hours, see your veterinarian.
• This product is not a toy, please keep away from children.
• This product is only for use with healthy dogs over 6-month old.

Charge the Remote and Receiver Collar

When charging is completed, display the fully charged battery compartment.

When charging is completed, steady green light.

Turn on the Remote

Flick down to unlock the remote.

Flick up to lock the remote.

Fit the Receiver Collar

The contact points must have direct contact with the dog's neck skin. Check the tightness of the collar by inserting one finger snugly between the collar and neck.

Static Stimulation

Delivers currently selected level static stimulation to the receiver collar.
Note: Please use with caution static stimulation, some dogs may not respond to lower levels. See the "How To Find The Best Static Level For Your Dog". "O" means none, "16" means the highest level.

Main Features

Beep Vibration and Static training mode

Battery status display for the remote

Remote range is up to 1000 feet

Long life Lithium Polymer battery

0-16 adjustable static level

Receiver collar is IPX7 waterproof

Remote non-waterproof

Support maximum 2 receiver collars with 1 remote

USB-C charging port

Training Tips

If you want to correct the dog's bad behavior, for example, barking, please follow these training steps.

1. Put a separate non-metallic collar on your dog's neck above the receiver collar, and attach an 8-10 feet leash.
   
   Be sure the extra collar does not put pressure on the contact points.
2. Hold the leash and the remote.
3. Choose your pet's recognition static level.
4. As soon as your pet is barking, press the stimulation button and give the command "No" or "No barking."
5. Release the stimulation button immediately once your dog stops barking and praise it.
6. If your pet ignores the stimulation, increase the Intensity Level by 1 to 3.
7. Practice this training in several different scenes.

Pairing

Note: You may skip this step because the set is already paired by factory setting.

1. Make sure the receiver collar is turned off, make sure the channel switch of remote is on "Dog 1".
2. Press and hold the power button of receiver collar for 3 secs until the red and green lights flash alternately.
   

3. Press and hold the Beep and Vibration buttons of remote at the same time to paring the receiver collar.
   
4. Pairing successful, the receiver collar beeps 3 time and the green light flashes 3 time.
   

Two Receiver Collars System

Part |: Pairing 2nd Receiver Collar
Note: You need own an additional receiver collar.

1. Make sure the receiver collar is turned off, make sure the channel switch of remote is on "Dog 2".
2. Press and hold the power button of receiver collar for 3 secs until the red and green lights flash alternately.
3. Press and hold the Beep and Vibration buttons of remote at the same time to paring the receiver collar.
4. Pairing successful, the receiver collar beeps 3 time and the green light flashes 3 time.

Part Il: Receiver Switching
Able to train 2 dogs separately. Regulator channel switch select the dog to train.

Question & Answer

Q: Is the static safe for my pet?
A: Static electricity may hurt your pet, please select the appropriate static electricity level. Electronic training equipment requires the interaction and training of the owner.

Q: How old does my pet have to be before using the electronic training collar?
A: Your pet should be able to recognize basic obedience commands such as "Sit" or "Stay". Pets should be at least 6 months old before using the training collar.

Q: Once my pet is trained and has been obeying my commands, will he have to continue to wear the receiver collar?
A: It is recommended to wear it until you completely correct the dog's bad behavior.

Q: Is the receiver collar waterproof?
A: Yes, the receiver collar is IPX7 waterproof. But the remote is not waterproof. Please keep the remote away from water.

Q: Will | get exactly 1000 feet of range with the electronic training collar?
A: The effective wireless communication range will be affected by terrain, weather, vegetation, and interference from other radio equipment.

Q: How can I get support when I have product problems?
A: Please feel free to contact our official customer service mailbox, any problems about the product will be resolved here. service@patpet.com

Troubleshooting

My pet does not respond when i press a button.

1. Make sure the receiver collar has been turned on.
2. Make sure the remote channel 1 or 2 is correct with the receiver collar. If not, please pairing the remote and the receiver collar again. Refer to "Paring" for more information.
3. Check the battery may be low in either the remote or the receiver collar.
4. Make sure the receiver collar's contact points are placed snugly against your pet's skin. Refer to "Fit The Receiver Collar" for more information.
5. Terrain, weather, vegetation, transmission from other radio devices, and many other factors can impact the amount of range you have with the unit.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download PATPET p-collar 356 - Dog Training Collar Manual