PATPET p-collar 301 - Remote Training Collar Quick Start Guide

Important Safety Information

Patpet dog training collar is designed to let dogs live safely, happily and get along with people more harmoniously.

Do not use with aggressive dogs.
Aggressive dogs can cause severe injury and even death to their owner and others. If you are unsure whether this product is appropriate for your dog, please consult your veterinarian or certified trainer.

Safety during on-leash training.
It is vitally important that you and your dog remain safe while learning during on-leash training. Your dog should be on a strong leash, long enough for him to attempt to chase an object, but short enough for him not to reach a road or other unsafe area. You must also be physically strong enough to restrain your dog when he tries to chase.

Risk of skin damage.
Please read and follow the instructions in this manual. Proper fit of the collar is important. A collar worn for too long or made too tight on the pet's neck may cause skin damage ranging from redness to pressure ulcers. This condition is commonly known as bed sores.

• Avoid leaving the collar on the dog for more than 12 hours per day. When possible reposition the collar on the pet's neck every 1 to 2 hours.
• Never connect a lead to the electronic collar; it will cause excessive pressure on the contacts.
• If a rash or sore is found, discontinue use of the collar until the skin has healed.
• If the condition p ersists beyond 48 hours, see your veterinarian.
• This product is not a toy, please keep away from children.
• This product is only for use with healthy dogs.

Overview

Remote

1. LED Indicator
2. Tone Button
3. Level +
4. Level –
5. Vibration Button
6. Vibration Level Display
7. Shock Level Display
8. On/Off Button
9. Channel Conversion Button
   Press and Hold it for setting Vibration&Shock Level
10. Shock Button
11. Battery Capacity Display
12. Channel Display
13. High Shock Level Warning

Receiver Collar

14. Contact Points
15. Conductive Silicone Covers
16. LED Indicator
17. On/Off Button

Setting Up the Product

Before you can use the Dog Training Collar, you must set up the product using the steps below:

1. Prepare the Remote--install batteries and turn it on.
2. Prepare the Receiver Collar--install batteries, Contact Points, Conductive Silicone, then assemble them, turn the Receiver Collar on.
3. Function test --test function of buttons before putting it on dog.
4. How to Use the Test Lamp--use the Test Lamp to test Shock function or use as a screw driver.
5. Pair the Remote and the Receiver Collar--Pair them when the receiver loses connection with the remote, add another receiver, or after change batteries.

Prepare the Remote

Install battery on the Remote

1. Push out the battery cover to remove it(1A).
2. Install the battery according to the engraved mark, negative (-) first, positive(+) next(1B).
3. Install the battery cover on the Remote(1C).

Turn ON/OFF the Remote

1. Press the ON/OFF Button on the Remote once to turn it ON.
2. LCD will be lighted, and show the information of current channel, battery power and levels. If not, please check the batteries position or change new batteries.
3. Press and hold the ON/OFF Button on the Remote to turn it OFF until the LCD display goes off, then release. It may take 2-3 seconds.

Note: When the remote is on, the LCD display will appear when any button is pressed.

Prepare the Receiver

Install battery on the Receiver

1. If the conductive screws are on, remove them first. Pop out the battery cover to remove it(2A).
2. Install the battery according to the engraved mark(2B).
3. Install the battery cover on the Receiver Collar(2C).

Install the Contact Points & Conductive Silicone

1. Select the correct Contact Points and Conductive Silicone length for your dog's coat type:

• For dogs with thicker coats, Use 2pcs longer Contact Points and Conductive Silicones.
• For dogs with shorter coats, Use 2pcs shorter Contact Points and Conductive Silicones.

Note:

1. Don't install the Metal Contact Points when shock function is not used.
2. Insert the Contact Points into the ports of the collar, use the Test Lamp to rotate clockwise to tighten them(3A).
3. Install the Conductive Silicone onto the Contact Points to make it softer, which will be better for dog's skin(3B).

Assemble Collar Strap

1. Unhitch the nylon belt and take off the Slide Buckle(4A).
2. Thread the strap through the Receiver Collar(4B).
3. Thread the slide buckle through the strap(4C).
4. Thread the strap through the side release buckle(4D).
5. Thread the excess strap through the slide buckle to make sure the collar strap is surely tight(4E).

Turn on the Receiver Collar

• Press the On/Off Button the Green LED light comes on.
• In normal mode, the Green LED will flash every 4 seconds, indicating the Receiver Collar is on and ready to receive signal from the Remote.

Turn off the Receiver Collar

• Press and hold the On/Off Button until the Red LED light shuts off (This takes approximate 3 seconds).
• Release the On/Off Button.

NOTE: To extend the life of the batteries, please turn the Receiver Collar off when it is not in use. Remove the battery if you don't use it for a long time.

Function Test

We recommend you experience the different shock/vibration levels firsthand on yourself. Please begin at the lowest level, then increase level gradually to your personal comfortable level. You can do as below.

1. Place one finger over both contact points of the training collar.
2. Hold your remote approximately 2 ft from the receiver collar. Press the Vibration Button continuously for 1 to 2 seconds. You should feel continuous vibration.
3. Press and hold for about 5 seconds until the Shock icon flashes, press +/- to adjust levels.
4. Increase the level until the sensation begins to feel uncomfortable.

NOTE: Continuous stimulation will transmit for no more the 10 continuous seconds. To reactivate, release and repress the button.

	Vibration: send vibration command ranging1-8 to the Receiver Collar.
	Tone: send a tone with non-adjustable level to the Receiver Collar.
	Shock: sends shock command ranging 1-16 to the Receiver Colar. Warning sign will show when the level is over 8.
	Channel Conversion: Press shortly once to swtich dog and dog channel. Vibration & Shock Level Adjustment: Press and hold for about 5 seconds until the Vibration/Shock Level display flashes, press +/- to adjust levels.
	increase the Shock/Vibration Level.
	Decrease the Shock/Vibration Level.

Note:

• Press and hold until the Vibration/Shock Level display flashes to set Vibration/Shock Level.
• The Shock Level can be adjusted from 1 to 16 levels and the Vibration Level from 1 to 8 levels; please adjust it properly as per your dog's reaction.
• Don't press and hold the Vibration/Shock Button too long, to avoid physical or psychological hurt to the dog.

How to Use the Test Lamp

Shock Function Test

1. Turn on the Receiver Collar.
2. Hold the Test Lamp contacts against the Contact Points (or Conductive Silicone Covers).
3. Press the Shock Button and the Test Lamp will be lighted. It will be brighter as the Shock Level is increased

As a Screw Driver

Use the Test Lamp to tighten or loosen the Contact Points when preparing the Receive Collar.\

Pair the Remote and Receive Collar

1. Use the Dog Button an the Remote to select Dog.
2. With the Remote turned on and the Receive Collar turned off, press and hold the ON/OFF Button on the Receiver Collar for 4-5 seconds.
3. The Red & Green LED will blink for about 10 seconds indicating that it is ready for pairing.
4. Press and hold the first Tone Button and the second Vibration Button at the same time for 2-3 seconds, when the LED on the Receiver Collar flashes green for 5 times indicating successful pairing.

Pairing a Second Collar with the Remote

1. Short press Button on the Remote to select Dog. Then follow the above pairing steps from 2-4.

Dog Trainig

Selecting The Contact Points and The Conductive Silicone Covers

For the best results, select the correct Contact Points based on your dog's coat.

• For dogs with thicker coats, Use 2pcs londer Contact Points and Conductive Silicones corers.
• For dogs with shorter coats, Use 2pcs shorter Contact Points and Conductive Silicones.

Fit the Training Fitting

Please fit the collar properly so that the Contact Points press firmly against the dog's skin. When properly fitted, you can be able to put a finger in between the Receiver Collar and dog's neck.

Too loose: the Receiver Collar will move around the dog's neck, the friction of Contact Points may hurt the dog's skin.

Too tight: it may cause dog's th breathe hard

1. Do not shave the pet's neck as this may increase the rick of skin irritation.
2. The collar should not be worn for more that 12 hours per day. Or it may cause harm to dog's skin.

Find the Best Shock Level for Your Pet

The unit comes with Up and Down buttons to control the Shock Level, with Level 1 being the lowest level and Level 16 being the highest.
The most suitable shock level depends on your dog's temperament and threshold for Shock. Always start at the lowest level and work your way up. The appropriate level can be found when the dog responds to the Shock with a mild reaction, such as a flick of the ear, a lick of the lips, a tensing of the neck muscles etc. The Shock Level may vary depending on the training situation. When highly distracted, dogs will require a higher level of Shock.

Product Information

Product Specification

The batteries need replaced under the situation below

1. The indicator light on the Receiver Collar is emiting a red color every 4 seconds or flashes rapidly
2. The battery icon on the Remote LCD shows just 1 bar. (When battery is low, the shock function will be affected)
3. The indicator light on the Remote or Receiver Collar will not come on.
4. The indicator light on the Remote or Receiver Collar comes on momentairly when any of the Mode Buttons is pressed.

Frequently Asked Questions

Troubleshooting Guide