Filling And Attaching The Milk Container; Adjusting The Amount Of Froth; Making Cappuccinos And Milk-Based Coffees; Automatically - DeLonghi DINAMICA PLUS ECAM370.95.T Instructions For Use Manual

8.1 Filling and attaching the milk container

1. Remove the lid (E2) (fig. 14);
2. Fill the milk container (E3) with a sufficient quantity of milk,
not exceeding the MAX level marked on the container (fig.
15). Each mark on the side of the container corresponds to
about 100 ml of milk;
Please note!
• For a denser more even froth, you must use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
• If "Energy Saving" mode is enabled, you may have to wait a
few seconds before the beverage is delivered.
3. Make sure the milk intake tube (E4) is correctly inserted in
the bottom of the milk container lid (fig. 16);
4. Place the lid back on the milk container;
5. Remove the hot water spout (D6);
6. Attach the milk container (E) to the connection nozzle (A8)
and push as far as it will go (fig. 17). The machine emits a
beep (if the beep function is enabled);
7. Place a sufficiently large cup under the coffee spouts (A9)
and the frothed milk spout (E5). Adjust the length of the
milk spout. To move it nearer the cup, simply pull it down-
wards (fig. 18).
8. Follow the instructions below for each function.

8.2 Adjusting the amount of froth

Turn the froth adjustment dial (E1) to adjust the amount of froth
on the milk delivered while making cappuccinos and milk-based
coffees.
Dial Description
position
NO FROTH
MIN. FROTH
MAX. FROTH

8.3 Making cappuccinos and milk-based coffees

automatically

1. Fill the milk container (E) and attach it as described above.
2. Select the required beverage:
• CAPPUCCINO
• LATTE MACCHIATO
• HOT MILK
• CAPPUCCINO+
Recommended for...
HOT MILK (not frothed) /
CAFFELATTE
latte macchiato/
FLAT WHITE
CAPPUCCINO / CAPPUCCI-
NO+ / CAPPUCCINO MIX
/ ESPRESSO MACCHIATO /
HOT MILK (frothed)
• CAPPUCCINO MIX
• CAFFELATTE
• FLAT WHITE
• ESPRESSO MACCHIATO
3. A message on the display instructs you to turn the froth
adjustment dial (E1) according to the froth required by the
original recipe. Turn the dial on the milk container lid.
4. After a few seconds, preparation begins automatically and
an image of the selected beverage appears on the display,
together with a progress bar which gradually fills as prepa-
ration progresses.
Once the coffee has been delivered, the machine will be ready
for further use.
Please note: general indications when preparing all milk-
based beverages
• : press to interrupt preparation completely
and go back to the homepage.
• : press to interrupt milk or coffee delivery and
move on to the next delivery (if applicable) to complete the
beverage.
• Preparation of each coffee can be customised (see sections
"11. Customising the beverages" and "12. Memorising
your own user profile").
• Do not leave the milk container out of the refrigerator for
long periods. The warmer the milk (5°C is ideal), the poorer
the quality of froth produced.
8.4

Cleaning the milk container after use

Each time you use a milk function, "TURN MILK FROTH ADJUST-
MENT DIAL" "TO CLEAN POSITION" appears on the display and
the milk frother lid must be cleaned:
1. Leave the milk container (E) in the machine (you do not
need to empty it);
2. Place a cup or other recipient under the frothed milk spout;
3. Turn the froth adjustment dial (E1) to "CLEAN" (fig. 19).
"CLEANING UNDERWAY" "RECIPIENT UNDER SPOUT" ap-
pears on the display together with a bar which gradually
fills as cleaning progresses (fig. 20). Steam mixed with hot
water comes out of the frothed milk spout. Cleaning stops
automatically;
4. Turn the dial back to one of the froth selections;
5. Remove the milk container and always clean the hot water
connection nozzle (A8) with a sponge (fig. 21).
Please note!
• To prepare a number of cappuccinos and milk based cof-
fees, clean the milk container after you have prepared
the last beverage only. To proceed with making the next
beverages, when the CLEAN message is displayed, press
.
36