Application Advice; Maintenance & Service; Declaration Of Conformity - Skil 1210 AA Original Instructions Manual

• Holding and guiding the tool 6
- guide the tool parallel to the working surface
! while working, always hold the tool at the
grey-coloured grip area(s)
! do not apply too much pressure on the tool; let
the sanding surface do the work for you
- do not tilt the tool in order to avoid unwanted sanding
marks
- keep ventilation slots J 2 uncovered

APPLICATION ADVICE

• For sanding bare wood surfaces move the tool in straight
movements in line with the grain
• For sanding all other surfaces move the tool in oval
movements over the material
• Mount sanding frame K (SKIL accessory 2610398244)
for equalizing surfaces without scratches or grooves, and
ensure it is in place securely 7
! sanding frame k becomes hot during use; do not
touch it before it has cooled down
• Never use the same sanding belt for wood and metal
• Recommended sanding belt grits:
coarse - for removing paint; for sanding of extremely
rough wood
medium - for sanding of rough or plain wood
ine - for smoothing of wood; for inishing of bare
wood; for smoothing surfaces with old paint
• Use diferent grit sizes when the working surface is
rough:
- start sanding with coarse or medium grit
- inish with ine grit
• For more tips see www.skil.com
mAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots J 2)
- remove adhering sanding dust with a brush
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
ENVIRONmENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 8 will remind you of this when the need for
disposing occurs

DECLARATION OF CONFORmITY

• We declare under our sole responsibility that the product
described under "Technical data" is in conformity with the
following standards or standardization documents: EN
60745, EN 61000, EN 55014, in accordance with the
provisions of the directives 2004/108/EC, 2006/42/EC,
2011/65/EU
• Technical file at: SKIL Europe BV (PT-SEU/ENG1),
4825 BD Breda, NL
07.08.2013
NOISE/VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 87 dB(A) and the sound
power level 98 dB(A) (standard deviation: 3 dB), and the
vibration 2.1 m/s² (hand-arm method; uncertainty
K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for diferent applications, or with diferent
or poorly maintained accessories, may signiicantly
increase the exposure level
- the times when the tool is switched of or when it is
running but not actually doing the job, may signiicantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Ponceuse à bande
INTRODUCTION
• Cet outil est conçu pour le ponçage à sec avec une
grande capacité à enlever la matière du bois, plastique,
métal et mastic et des surfaces peintes
• Cet outil n'est conçu pour un usage professionnel
• Lisez et conservez ce manuel d'instruction 3
CARACTERISTIQUES TECHNIQUES 1
ELEmENTS DE L'OUTIL 2
A Interrupteur marche/arrêt
B Bouton de verrouillage de l'interrupteur marche/arrêt
C Levier pour changer la bande de ponçage
D Flèche
7
1210/1215