Application Advice; Maintenance & Service; Noise / Vibration - Skil SR1E7280DA Original Instructions Manual

! replace worn sanding sheets in time
! always use the tool with the total sanding surface
covered with sanding paper
- mount VELCRO sanding sheet as illustrated
• Dust suction
! do not use dust box/vacuum cleaner when
sanding metal
Dust box 8
- empty dust box K regularly for optimal dust pick-up
performance 8 b
- Mount the dust box K as illustrated 8 a.
For using vacuum cleaner 9
- mount vacuum cleaner adapter L as illustrated
- connect vacuum cleaner hose to vacuum cleaner
adapter L
• On/off switch
- switch on/off the tool by pushing switch F 2 forward/
backwards
! before the sanding surface reaches the workpiece,
you should switch on the tool
! before switching off the tool, you should lift it from
the workpiece
• Speed control q
For optimal sanding results on different materials
- with wheel J 2 you can set the desired sanding speed
- adjust speed to grit size used
- before starting a job, find the optimal speed and grit by
testing out on spare material
• Holding and guiding the tool w
! while working, always hold the tool at the grey-
coloured grip area(s)
- guide the tool parallel to the working surface
! do not apply too much pressure on the tool; let the
sanding surface do the work for you
- do not tilt the tool in order to avoid unwanted sanding
marks
- keep ventilation slots M 2 uncovered
• Overload Alert e
Warns the user when applying too much pressure on
the tool while working (too much pressure reduces the
sanding performance)
- red light turns on when pressure is too high

APPLICATION ADVICE

• For sanding curved workpieces as well as for sanding
with high removal performance use the tool in
combination with backing pad B y
• Use the tool with the delta-tip pointing forward for edged,
narrow and other hard-to-reach places r
• When the delta-tip is worn or damaged at the top, you
may extend its service life twice by removing it, turning it
120° and putting it back (also applicable to delta sanding
sheet) u
• Never use the same sanding sheet for wood and metal
• Recommended sanding sheet grits:
- for removing paint and for sanding of extremely rough
wood use coarse grit sizes (40, 60)
- for sanding of rough or plain wood use medium grit
sizes (80, 100, 120)
- for smoothing of wood and surfaces with old paint as
well as for finishing of bare wood use fine grit sizes
(180, 240, 320)
• Use different grit sizes when the working surface is
rough:
- start sanding with coarse or medium grit
- finish with fine grit
• For more information see www.skil.com
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots M 2 )
- remove adhering sanding dust with a brush
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
• Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 5 will remind you of this when the need for
disposing occurs

NOISE / VIBRATION

• Measured in accordance with EN 62841 the sound
pressure level of this tool is 80.5 dB(A) and the sound
power level 91.5 dB(A) (uncertainty K = 3 dB), and
the vibration 7.8 m/s² (triax vector sum; uncertainty
K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 62841;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
12